Ender3 V2/S1 Professional Firmware 20230312 #785
Replies: 23 comments 65 replies
-
|
I come from using Jyers firmware just fine (actually just finish print) and I got the BLT 4.2.2 version of this firmware but when I turn on my v2 with the SD in... the screen gets stuck on the CREALITY logo.. I can rollback to Jyers by loading the jyer's bin on the SD.. that loads fine but the latest version of this firmware for BL touch and 422 board (Ender3V2-422-BLTUBL-MPC-20230312.bin) cant load.. tried a few times.. formatted the card several times.. renamed the bin file to multiple names (even just firmware.bin) but still the same.. is just me? |
Beta Was this translation helpful? Give feedback.
-
From what I've experienced, if your E3V2 has a DACAI screen you need to install the Creality factory firmware first then load the Professional Firmware. E3V2's with a DWIN screen will load without needing to revert back to the factory firmware first. |
Beta Was this translation helpful? Give feedback.
-
weird that I got the same chip but this issue... maybe resetting from or something like that? |
Beta Was this translation helpful? Give feedback.
-
I will try that, thanks. |
Beta Was this translation helpful? Give feedback.
-
|
UPDATE: Finally got it to work and yes, the issue was on my end... after trying several other bin files, the only one actually loading was the Jyers 2.0.1 so from there I went and restored all settings to the factory, tried again, and nothing.. so I changed SD card from the one that came with the printer to a 32Gb Kingston that already had a "boot" partition I used that with no hope.. and after renaming the file and boom! it worked so I guess the issue was on the other SD or some setting stored in the ROM...? |
Beta Was this translation helpful? Give feedback.
-
|
Thanks @mriscoc for building a great firmware for my Creality 4.2.2 board and stm32f103 RET6 micro-controller. With the chaos Creality created by having multiple Ender 3 V2 boards and a mix of chipsets I appreciate you removing at least some of the complexity (supporting both 256 and 512 kb variants, etc.). I ended up making things more difficult than I needed to -- ultimately the issues I had flashing the main and display board were solved by:
(read the Wiki, discussions, and other markdown documents in this repo - a lot of great content here. Much easier than figuring out the difference between the various STM32F103RX platformio.ini environment settings...) |
Beta Was this translation helpful? Give feedback.
-
|
Does this latest version have linear advance and input shaping. I installed it and can’t get a good k value for LA. Not sure if I’m doing something wrong. |
Beta Was this translation helpful? Give feedback.
-
|
yo suelo actualizar en cuanto saca uno nuevo perder la configuracion si pero para que queremos el movil foto de la pantalla pasos,retracciones, etc y luego se las introduces y las compruebas total no se actualiza todos los dias |
Beta Was this translation helpful? Give feedback.
-
|
Para mantener la configuración entre actualizaciones: https://github.com/mriscoc/Ender3V2S1/wiki/Configuration-files |
Beta Was this translation helpful? Give feedback.
-
|
@mriscoc so I am totally lost here, I just don't understand how github works, so I am posting a reply to this post hoping that someone can help me. I just upgraded my Ender 3V2 to the sprite hotend, but can only get to 260 degrees, I did find a special build that goes to 300, but it is listed as Ender3V2-422-BLTUBL-T13-MPC-20230312.bin, I am assuming the BLT is for the BL Touch, I do not have this, so is there one for Manual Mesh? Hope someone will help, thanks |
Beta Was this translation helpful? Give feedback.
-
|
I even tried the C104 U1 T315 ; set absolute limit to 315 °C (300 + 15 overshoot) any ideas |
Beta Was this translation helpful? Give feedback.
-
|
There isn't a precompiled firmware for the manual mesh version with Sprite Extruder Pro. You need to compile your own firmware or request one, check here: https://github.com/mriscoc/Special_Configurations#these-special-configurations-and-releases-are-sponsored-by-donors |
Beta Was this translation helpful? Give feedback.
-
|
hey , I just got a new Sprite extruder pro kit and downloaded the (Ender3V2-422-BLTUBL-MPC-20230312) sorry for my bad English, I'm French Canadian ! :) |
Beta Was this translation helpful? Give feedback.
-
|
https://github.com/mriscoc/Ender3V2S1/wiki/Calibration-Guides |
Beta Was this translation helpful? Give feedback.
-
|
I am using a pre-compiled version for now (until the December source code is updated). For my Ender 3 v2, the homing speed for Z is so fast that the nozzle hits the glass. Whereas it never used to hit the glass with a slower Z-Home speed. I don't understand this, since 1) the position of my limit switch did not change when I updated to mriscoc firmware. And 2) I cannot imagine that there is a lot of inertial in Z. Maybe hitting the glass is due to inherent sloppiness/hysteresis in a mechanical switch? And so slower is better? Whatever, I will try to compile my own version with custom values someday. |
Beta Was this translation helpful? Give feedback.
-
|
if you have dumped configuration with M503 and could compare two, then maybe Feedrate on Z have changed |
Beta Was this translation helpful? Give feedback.
-
|
The March firmware runs perfectly on my Ender 3 V2 machine, just like the previous ones, but unfortunately still no thumbnail preview on my DACAI screen and I updated the display as well. Sorry for my bad English. |
Beta Was this translation helpful? Give feedback.
-
|
la verdad es que a mi me costo un poco hacerlo funcionar con windows 11 el python se instala en una ruta distinta a la del tutorial en mi caso windows 11 y python 3.0 |
Beta Was this translation helpful? Give feedback.
-
|
@mriscoc I'm sorry, but I still haven't resolved it. My Ender 3 S1 PRO uses a DWIN screen, and I have also updated the latest screen firmware and motherboard firmware. However, the GCODE test still cannot be previewed. I hope you can help me. Thank you very much.
|
Beta Was this translation helpful? Give feedback.
-
|
What display unit do you have? https://github.com/mriscoc/Ender3V2S1/wiki/How-to-update-the-display |
Beta Was this translation helpful? Give feedback.
-
|
@mriscoc DWIN display |
Beta Was this translation helpful? Give feedback.
-
|
Sorry, but with a If it had been a |
Beta Was this translation helpful? Give feedback.
-
|
I recently added the SKR Mini e3 V3 for my Ender 3 V2. Says to use an adapter since the pinouts are different. I got a new ribbon cable that's specific for the SKR Mini to the Ender 3 V2 display screen. Once downloaded firmware to flash printer, nothing happened. screen was still off. Not even a hint of light on the screen. So now I'm watching this guy on youtube trying to compile this firmware using this custom cable. Now, on VS Code, what should i put for the motherboard. Delete what's there in default and add SKR MINI e3 V3? Hopefully this file will work. Thanks |
Beta Was this translation helpful? Give feedback.
-
|
In Discussion, look for the SKR Mini support, you will see how to connect the cable there. |
Beta Was this translation helpful? Give feedback.
-
|
Okay. found out the problem. i guess when turning it on the first time, might have blown the fuse. tested the fuse and got nothing. replaced with my old creality board and the screen came on but now. it's just the screen that's frozen on just creality. still have to flash the printer again or is the board fried because the fuse didnt work? |
Beta Was this translation helpful? Give feedback.
-
|
Nevermind, Mr. Castillo. Got it to run Mriscoc. Calibration time. Love your work. |
Beta Was this translation helpful? Give feedback.
-
|
en principio darte las gracias por el bien que nos haces y lo otro es una consulta descargue en friware de la pantalla pero en el repositorio dentro de las carpetas que muestra la wep pone español o lo e leido mal por que si se puede me gustaria que me explicases como |
Beta Was this translation helpful? Give feedback.
-
|
Actualmente solo el inglés está totalmente soportado. Puedes cambiar parcialmente el idioma modificando el valor de Ender3V2S1/Marlin/Configuration.h Lines 2510 to 2520 in 98a967b |
Beta Was this translation helpful? Give feedback.
-
|
i have cura 5.3.0. print speed settings say 55% is not getting transferred to gcode output. i updated the machine settings with the start and end gcode from the wiki. Using V2 Neo. Interesting same works if i use prusa. Any idea ? |
Beta Was this translation helpful? Give feedback.
-
|
How do I re-enable the auto cooldown after a print is finished? my ender 3 v2 keeps my bed heated until I manually turn it off after a print |
Beta Was this translation helpful? Give feedback.
-
|
That is a task for your end G-code script. In the latest version ProUI doesn't force you to disable the motors or cooldown. Of course, you can easily cooldown and disable motors in the end G-code script. Marlin sends the G-code M84 at the end of the printing if SD_FINISHED_STEPPERRELEASE is enabled, disabling the stepper drivers. Also, the heaters are cooled down after the DEFAULT_STEPPER_DEACTIVE_TIME. |
Beta Was this translation helpful? Give feedback.
-
|
Hi, So I have SKR Mini E3 v3.0.1, is it possible at all to use this firmware? I have tried flashing it with edited config file to reflect my board (and changing the LCD_SERIAL_PORT condition to include BTT_SKR_MINI_E3_V3_0_1), but the screen just freezes after the boot screen. Any ideas? |
Beta Was this translation helpful? Give feedback.
-
|
Check the screen cable: #131 |
Beta Was this translation helpful? Give feedback.
-
|
I have indeed checked the cable, I think it is correct. I have tried to install Marlin bugfix-2.1.x with MarlinUI, and the screen seems to work normally (although I have problems with communication timeout in octoprint). In fact, I have completed a print from SD using Marlin bugfix-2.1.x. It seems that only when I use the Pro firmware that the screen freezes after boot. |
Beta Was this translation helpful? Give feedback.
-
|
We tested with the SKR Mini E3 V3 version; I don't know what are the differences with the V3.0.1 |
Beta Was this translation helpful? Give feedback.
-
|
From what I've read, the difference seems to be the CPU mainly (STM32F401RC), and the absence of exposed IO Pins. Other than that, I'm not sure. |
Beta Was this translation helpful? Give feedback.
-
|
For what it's worth, I've loaded this onto my Ender 3 V2 with the
Currently running my first test print after a manual mesh, so far so good. |
Beta Was this translation helpful? Give feedback.
-
|
Hello, Filename is Experimental-Ender3V2-422-MM-LA-MPC-20230312.bin Thank you :) |
Beta Was this translation helpful? Give feedback.
-
|
MPC is a more advanced algorithm than PID but also require to have more care, cooling to ambient means that the system is waiting to the thermistor to reach about of 25 degrees, that could be not possible under certain conditions. |
Beta Was this translation helpful? Give feedback.
-
|
thanks for your reply, where could I request this, I am a high school
teacher, and I am a bit desperate to get this printer up and running for my
students,
thanks
…On Sun, Apr 30, 2023 at 1:58 AM Miguel Risco-Castillo < ***@***.***> wrote:
There isn't a precompiled firmware for the manual mesh version with Sprite
Extruder Pro. You need to compile your own firmware or request one, check
here:
https://github.com/mriscoc/Special_Configurations#these-special-configurations-and-releases-are-sponsored-by-donors
—
Reply to this email directly, view it on GitHub
<#785 (reply in thread)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AKHNU6YUBAOJSWUOLQK4RQTXDYLQXANCNFSM6AAAAAAVYMABSY>
.
You are receiving this because you commented.Message ID:
***@***.***>
--
------------------------------
Don Reichert (B.Ed, B.Mgmt)
Catholic Central High School
PH: 403-327-4596
Fax: 403-320-8896
|
Beta Was this translation helpful? Give feedback.
-
|
You can request custom built bins by sponsoring @mriscoc to do the extra work for you. Or you can build the bin yourself if you are feeling adventurous. |
Beta Was this translation helpful? Give feedback.
-
|
as much as I would like to, this is for a school, and we are not allowed to subscribe to these sort of things, we can only purchase tangible objects, so I will either have to find an alternative firmware or buy a BLTouch |
Beta Was this translation helpful? Give feedback.
-
|
I have an Ender 3 S1 PRO, with the (lousy) touchscreen interface. The statement that "A DWIN or DACAI color screen with encoder knob. Touch or legacy monocrome screens are not supported," seems to exclude my printer from using this firmware. Can you clarify or confirm? I upgraded the display firmware using Creality's latest a couple of weeks ago. Would that be a problem, assuming the touchscreen is actually supported otherwise? |
Beta Was this translation helpful? Give feedback.
-
|
The Touchscreen is not compatible at the present time. You can pick up a DACAI screen here (or elsewhere) to replace your touchscreen and then proceed with the install as normal. Just remember to follow the screen flashing part of the install instructions to initially prepare the new screen. https://www.amazon.com/gp/product/B098WFCQYW You can then hold onto the touchscreen until it is later supported (it will be a while) or sell off the touchscreen on the secondhand markets to recoup the cost of the other screen. |
Beta Was this translation helpful? Give feedback.
-
|
The cable for the DACAI screen looks different in terms of pinout compared to the one with the kit. (The board connector is indicated in orange.) I suppose some rewiring would be in order. |
Beta Was this translation helpful? Give feedback.
-
|
That's the touchscreen interface, the DACAI screen would be connected to J704. |
Beta Was this translation helpful? Give feedback.
-
Can I use one of the 12864 LCD displays (monochrome, bitmap, with a rotary encoder dial and clicker) as well, plugged into J704? |
Beta Was this translation helpful? Give feedback.
-
|
Hello, |
Beta Was this translation helpful? Give feedback.
-
|
It has a TJC display, which currently requires a custom build. |
Beta Was this translation helpful? Give feedback.
-
|
How can I get a custom build? My knowledge of building firmware is non-existent. |
Beta Was this translation helpful? Give feedback.
-
Beta Was this translation helpful? Give feedback.
-
|
Hi mriscoc......sorry if this is a bit simple. Give me computers and I can do anything but i really struggle to compile my own firmware for some reason. I have a stock standard E3V2 with CRTouch and dual z rod. Its the 4.2.2 RCT6 and CRTouch. I currently do a ABL 5 x 5 probe each time I print (I dont mind it doing a probe on each print). If I were to flash it with your UBL Ender3V2-422-BLTUBL-MPC-20230312.bin and change the Gcode from G29 to G29 P1 would it still do a 5 x 5 bed probe before each print if I set your software to probing points of 5 ??????? Also one other quick question please. If I use the firmware retraction, does this override the cura gcode created slicer retraction setting or would it conflict with one another. Many regards Bruce from NZ |
Beta Was this translation helpful? Give feedback.
-
|
Further to my comment above, it looks like i want all the features of the Ender3V2-422-BLTUBL-MPC-20230312.bin but only change the configuration for it to do BLT ABL bi-linear. I note rather than recompiling the whole firmware, you can make a file to put onto sd card that would customise just the part you want. Is anybody able to help me out to make a customisable file to change it from UBL to ABL bi-linear and just putting it onto sdcard to put into the printer. I would really appreciate the help someone could offer. |
Beta Was this translation helpful? Give feedback.
-
|
That's not the kind of configuration option you can change dynamically, you need a recompiled firmware for it. Except for having to change G29 to G29 P1 in your slicer setup, you shouldn't see a big difference between ABL and UBL for simple cases. |
Beta Was this translation helpful? Give feedback.
-
|
Thank you @dfinberg I was worried changing to UBL would confuse things for me but if it stays pretty much the same by changing the gcode and that the printer will do a 5 x 5 probe before each print then that will be great. I see in the printer setup there is firmware retraction. Do you know if this is activated does it override the slicer retraction settings and therefore they wont conflict with one another ???? Again thank you for you answer above |
Beta Was this translation helpful? Give feedback.
-
|
https://github.com/mriscoc/Ender3V2S1/wiki/Firmware-Retraction Looks like it is a choice between one or the other, so they won't conflict. If you don't activate it, then your slicer's settings will control. If you do activate it, then the firmware will try and convert software retractions (i.e. G1 E-2) to a FW retraction move, and ignore the SW instruction. |
Beta Was this translation helpful? Give feedback.
-
|
Hey, This project looks really interesting. Do you have any plans to include Creality touchscreen support? |
Beta Was this translation helpful? Give feedback.
-
|
No touchscreen support. |
Beta Was this translation helpful? Give feedback.
-
|
Hello, I am currently using FW: I have an Ender 3 V2, 4.2.2 board with an STM32F soc, and a BL touch I installed, everything is working good. Thanks for your dedication and hard work on this amazing firmware. |
Beta Was this translation helpful? Give feedback.
-
|
A new version will be coming very soon. |
Beta Was this translation helpful? Give feedback.
-
|
Hello, I want to calibrate/verify my extruder esteps with: |
Beta Was this translation helpful? Give feedback.
-
|
The extruder movements are protected by the minimum extrusion temperature in filament settings. |
Beta Was this translation helpful? Give feedback.
-
|
Thanks for the reply. I preheated PLA in the settings and it would still not move, is there another setting I could use? |
Beta Was this translation helpful? Give feedback.
-
|
Check your extruder steps/mm, verify that you have the correct firmware version for your board, try to move another motor. |
Beta Was this translation helpful? Give feedback.
-
|
I needed to restart the app and printer and it works with the print head heated. Thanks |
Beta Was this translation helpful? Give feedback.
-
|
Possibly you have flashed a incorrect board version firmware. |
Beta Was this translation helpful? Give feedback.
-
|
Hello , thanks a lot for this update, I was suffering from the lake of the Z indicator in the official version, and also from the flactuating nozzle temperature. Just installed your update a few minutes ago and seems perfect, thanks again. |
Beta Was this translation helpful? Give feedback.
-
|
Hi thanks. |
Beta Was this translation helpful? Give feedback.
-
|
This should be probably turned on by default. :) |
Beta Was this translation helpful? Give feedback.
-
|
Is there a way to install this from the source code download? I am not sure what files I am looking for. This is the version I currently have running on my S1 Pro and I just want a back up file incase anything happens. |
Beta Was this translation helpful? Give feedback.
and others
-
Boreal Spring 2023
What's new in this release
From Marlin 2.1.2
This firmware is based on Marlin, has been optimized and has enhancements for the Creality Ender 3 V2/S1 printer. This is an universal firmware that can be used in both RET6 and RCT6 STM32FX chips that have 256k or 512k Flash memory. The firmware and its wiki are not really intended for beginners but as a supplement to already existing guides.
How to install the firmware
Requirements
In order to use this firmware, your printer must meet the following requirements:
You can modify your printer to meet these requirements.
Versions
You can download the latest binaries from the assets at the bottom of
the release page.
To know if you have the last release go to the info page in the display of
your printer and compare the release build date with the name of the binary
file. The filename follows the convention:
Where YYYYMMDD indicates the date of the build. 422 refers to the mainboard
version 4.2.2, 423 refers to the mainboard version 4.2.3, and 427 is for the 4.2.7 mainboard version, if you got
a 4.3.1 board use the 422 version. SKRMINI version is currently for the
BTT SKR Mini E3 V3 board (needs a screen adapter).
For example, if you want a firmware for your Ender-3 V2 printer with a control
board version 4.2.2, CRTouch and support for UBL, you should download the file:
UBL versions
Binaries with UBL in their filename have support for Marlin Unified Bed Leveling, this system is similar to the bilinear leveling but with a few extra features to provide users with more control. There are multiple guides on the web about UBL, we recommend reading about it before using this new leveling system.
Model Predictive Temperature Control (MPC)
From this version MPC is being incorporated in all versions. MPC has proven to be a better algorithm for keeping the nozzle temperature stable, and is also very useful for high power heaters.
Special versions
There are several special configurations here: https://github.com/mriscoc/Marlin_Configurations/releases
Community links
Donations
Thank you for your support, I receive donations through Patreon and Paypal
Firmware features
Manual mesh
CR/3D/BLTouch
G-Codes enhanced support
Support for special nonstandard custom C G-Codes
version, Z parameter can be used to set a manual Z-offset.
Advanced settings menu
Special Octoprint / Host print support
Octoprint bed visualizer support
Display enhancements
A lot of additions and fixes from Bugfix development branch
More info on the wiki pages
How to install the firmware
Octoprint settings
How to make the Manual Mesh
How to install a 3D/BLTouch
How to apply a color theme
20211121.mp4
Precompiled firmware
This discussion was created from the release Ender3 V2/S1 Professional Firmware 20230312.
Beta Was this translation helpful? Give feedback.
All reactions