forked from openwrt/openwrt
Commit
This commit does not belong to any branch on this repository, and may belong to a fork outside of the repository.
ramips: add support for Netgear WAX202
Netgear WAX202 is an 802.11ax (Wi-Fi 6) router. Specifications: * SoC: MT7621A * RAM: 512 MiB NT5CC256M16ER-EK * Flash: NAND 128 MiB F59L1G81MB-25T * Wi-Fi: * MT7915D: 2.4/5 GHz (DBDC) * Ethernet: 4x 1GbE * Switch: SoC built-in * USB: None * UART: 115200 baud (labeled on board) Load addresses (same as ipTIME AX2004M): * stock * 0x80010000: FIT image * 0x81001000: kernel image -> entry * OpenWrt * 0x80010000: FIT image * 0x82000000: uncompressed kernel+relocate image * 0x80001000: relocated kernel image -> entry Installation: * Flash the factory image through the stock web interface, or TFTP to the bootloader. NMRP can be used to TFTP without opening the case. * Note that the bootloader accepts both encrypted and unencrypted images, while the stock web interface only accepts encrypted ones. Revert to stock firmware: * Flash the stock firmware to the bootloader using TFTP/NMRP. References in WAX202 GPL source: https://www.downloads.netgear.com/files/GPL/WAX202_V1.0.5.1_Source.rar * openwrt/target/linux/ramips/dts/mt7621-ax-nand-wax202.dts DTS file for this device. Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
- Loading branch information
Showing
6 changed files
with
318 additions
and
0 deletions.
There are no files selected for viewing
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
Original file line number | Diff line number | Diff line change |
---|---|---|
@@ -0,0 +1,277 @@ | ||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT | ||
|
||
#include "mt7621.dtsi" | ||
|
||
#include <dt-bindings/gpio/gpio.h> | ||
#include <dt-bindings/input/input.h> | ||
|
||
/ { | ||
compatible = "netgear,wax202", "mediatek,mt7621-soc"; | ||
model = "Netgear WAX202"; | ||
|
||
aliases { | ||
led-boot = &led_power_green; | ||
led-failsafe = &led_power_orange; | ||
led-running = &led_power_green; | ||
led-upgrade = &led_power_orange; | ||
}; | ||
|
||
chosen { | ||
bootargs = "console=ttyS0,115200"; | ||
}; | ||
|
||
keys { | ||
compatible = "gpio-keys"; | ||
|
||
reset { | ||
label = "reset"; | ||
gpios = <&gpio 10 GPIO_ACTIVE_LOW>; | ||
linux,code = <KEY_RESTART>; | ||
}; | ||
}; | ||
|
||
leds { | ||
compatible = "gpio-leds"; | ||
|
||
led_power_green: power_green { | ||
label = "green:power"; | ||
gpios = <&gpio 0 GPIO_ACTIVE_LOW>; | ||
}; | ||
|
||
led_power_orange: power_orange { | ||
label = "orange:power"; | ||
gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; | ||
}; | ||
|
||
led_net_green: net_green { | ||
label = "green:net"; | ||
gpios = <&gpio 18 GPIO_ACTIVE_LOW>; | ||
}; | ||
|
||
led_net_blue: net_blue { | ||
label = "blue:net"; | ||
gpios = <&gpio 16 GPIO_ACTIVE_LOW>; | ||
}; | ||
|
||
led_lan1_green: lan1_green { | ||
label = "green:lan1"; | ||
gpios = <&switch0 3 GPIO_ACTIVE_LOW>; | ||
}; | ||
|
||
led_lan1_orange: lan1_orange { | ||
label = "orange:lan1"; | ||
gpios = <&gpio 15 GPIO_ACTIVE_LOW>; | ||
}; | ||
|
||
led_lan2_green: lan2_green { | ||
label = "green:lan2"; | ||
gpios = <&switch0 6 GPIO_ACTIVE_LOW>; | ||
}; | ||
|
||
led_lan2_orange: lan2_orange { | ||
label = "orange:lan2"; | ||
gpios = <&gpio 13 GPIO_ACTIVE_LOW>; | ||
}; | ||
|
||
led_lan3_green: lan3_green { | ||
label = "green:lan3"; | ||
gpios = <&switch0 12 GPIO_ACTIVE_LOW>; | ||
}; | ||
|
||
led_lan3_orange: lan3_orange { | ||
label = "orange:lan3"; | ||
gpios = <&gpio 14 GPIO_ACTIVE_LOW>; | ||
}; | ||
|
||
led_wifi2g_green: wifi2g_green { | ||
label = "green:wifi2g"; | ||
gpios = <&gpio 12 GPIO_ACTIVE_LOW>; | ||
linux,default-trigger = "phy0radio"; | ||
}; | ||
|
||
led_wifi2g_blue: wifi2g_blue { | ||
label = "blue:wifi2g"; | ||
gpios = <&gpio 7 GPIO_ACTIVE_LOW>; | ||
}; | ||
|
||
led_wifi5g_green: wifi5g_green { | ||
label = "green:wifi5g"; | ||
gpios = <&gpio 8 GPIO_ACTIVE_LOW>; | ||
linux,default-trigger = "phy1radio"; | ||
}; | ||
|
||
led_wifi5g_blue: wifi5g_blue { | ||
label = "blue:wifi5g"; | ||
gpios = <&gpio 6 GPIO_ACTIVE_LOW>; | ||
}; | ||
}; | ||
}; | ||
|
||
&nand { | ||
status = "okay"; | ||
|
||
partitions { | ||
compatible = "fixed-partitions"; | ||
#address-cells = <1>; | ||
#size-cells = <1>; | ||
|
||
partition@0 { | ||
label = "Bootloader"; | ||
reg = <0x0 0x80000>; | ||
read-only; | ||
}; | ||
|
||
partition@80000 { | ||
label = "Config"; | ||
reg = <0x80000 0x80000>; | ||
read-only; | ||
}; | ||
|
||
factory: partition@100000 { | ||
label = "Factory"; | ||
reg = <0x100000 0x80000>; | ||
read-only; | ||
}; | ||
|
||
partition@180000 { | ||
label = "firmware"; | ||
reg = <0x180000 0x2600000>; | ||
|
||
compatible = "fixed-partitions"; | ||
#address-cells = <1>; | ||
#size-cells = <1>; | ||
|
||
partition@0 { | ||
label = "kernel"; | ||
reg = <0x0 0x400000>; | ||
}; | ||
|
||
partition@400000 { | ||
label = "ubi"; | ||
reg = <0x400000 0x2200000>; | ||
}; | ||
}; | ||
|
||
partition@2780000 { | ||
label = "firmware_backup"; | ||
reg = <0x2780000 0x2600000>; | ||
read-only; | ||
}; | ||
|
||
partition@4d80000 { | ||
label = "CFG"; | ||
reg = <0x4d80000 0x800000>; | ||
read-only; | ||
}; | ||
|
||
partition@5580000 { | ||
label = "RAE"; | ||
reg = <0x5580000 0x400000>; | ||
read-only; | ||
}; | ||
|
||
partition@5980000 { | ||
label = "POT"; | ||
reg = <0x5980000 0x100000>; | ||
read-only; | ||
}; | ||
|
||
partition@5a80000 { | ||
label = "Language"; | ||
reg = <0x5a80000 0x400000>; | ||
read-only; | ||
}; | ||
|
||
partition@5e80000 { | ||
label = "Traffic"; | ||
reg = <0x5e80000 0x200000>; | ||
read-only; | ||
}; | ||
|
||
partition@6080000 { | ||
label = "Cert"; | ||
reg = <0x6080000 0x100000>; | ||
read-only; | ||
}; | ||
|
||
partition@6180000 { | ||
label = "NTGRcryptK"; | ||
reg = <0x6180000 0x100000>; | ||
read-only; | ||
}; | ||
|
||
partition@6280000 { | ||
label = "NTGRcryptD"; | ||
reg = <0x6280000 0x500000>; | ||
read-only; | ||
}; | ||
|
||
partition@6780000 { | ||
label = "LOG"; | ||
reg = <0x6780000 0x100000>; | ||
read-only; | ||
}; | ||
|
||
partition@6880000 { | ||
label = "User_data"; | ||
reg = <0x6880000 0x640000>; | ||
read-only; | ||
}; | ||
}; | ||
}; | ||
|
||
&pcie { | ||
status = "okay"; | ||
}; | ||
|
||
&pcie1 { | ||
wifi@0,0 { | ||
compatible = "mediatek,mt76"; | ||
reg = <0x0000 0 0 0 0>; | ||
mediatek,mtd-eeprom = <&factory 0x0>; | ||
}; | ||
}; | ||
|
||
&pcie2 { | ||
status = "disabled"; | ||
}; | ||
|
||
&state_default { | ||
gpio { | ||
groups = "uart3", "uart2", "jtag", "wdt"; | ||
function = "gpio"; | ||
}; | ||
}; | ||
|
||
&switch0 { | ||
gpio-controller; | ||
#gpio-cells = <2>; | ||
|
||
ports { | ||
port@0 { | ||
status = "okay"; | ||
label = "wan"; | ||
}; | ||
|
||
port@1 { | ||
status = "okay"; | ||
label = "lan1"; | ||
}; | ||
|
||
port@2 { | ||
status = "okay"; | ||
label = "lan2"; | ||
}; | ||
|
||
/* port@3 is not used */ | ||
|
||
port@4 { | ||
status = "okay"; | ||
label = "lan3"; | ||
}; | ||
}; | ||
}; | ||
|
||
&xhci { | ||
status = "disabled"; | ||
}; |
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters