forked from openwrt/openwrt
Commit
This commit does not belong to any branch on this repository, and may belong to a fork outside of the repository.
ath79: add support for Teltonika RUT230 v1
This commit adds support for the Teltonika RUT230 v1, a Atheros AR9331 based router with a Quectel UC20 UMTS modem. Hardware -------- Atheros AR9331 16 MB SPI-NOR XTX XT25F128B 64M DDR2 memory Atheros AR9331 1T1R 802.11bgn Wireless Boootloader: pepe2k U-Boot mod Hardware-Revision ----------------- There are two board revisions of the RUT230, a v0 and v1. A HW version is silkscreened on the top of the PCBs front side as well as shown in the Teltonika UI. However, this looks to be a different identifier, as the GPl dump shows this silkscreened / UI shown version are internally treated identically. Th following mapping has been obtained from the latest GPl dump. HW Ver 01 - 04 --> v0 HW Ver > 05 --> v1 My board was a HW Ver 09 and is treated as a v1. Installation ------------ While attaching power, hold down the reset button and release it after the signal LEDs flashed 3 times. Attach your Computer with the devices LAN port and assign yourself the IPv4 address 192.168.1.10/24. Open a web browser, navigate to 192.168.1.1. Upload the OpenWrt factory image. The device will install OpenWrt and automatically reboots afterwards. You can use the smae procedure with the stock firmware to return back to the vendor firmware. Signed-off-by: David Bauer <mail@david-bauer.net>
- Loading branch information
1 parent
de49957
commit 6cf1dfd
Showing
3 changed files
with
230 additions
and
2 deletions.
There are no files selected for viewing
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| Original file line number | Diff line number | Diff line change |
|---|---|---|
| @@ -0,0 +1,193 @@ | ||
| // SPDX-License-Identifier: GPL-2.0-or-later OR MIT | ||
|
|
||
| #include "ar9331.dtsi" | ||
|
|
||
| #include <dt-bindings/gpio/gpio.h> | ||
| #include <dt-bindings/input/input.h> | ||
|
|
||
| / { | ||
| model = "Teltonika RUT230 v1"; | ||
| compatible = "teltonika,rut230-v1", "qca,ar9331"; | ||
|
|
||
| aliases { | ||
| label-mac-device = &wmac; | ||
| led-boot = &led_ss0; | ||
| led-failsafe = &led_ss0; | ||
| led-upgrade = &led_ss0; | ||
| }; | ||
|
|
||
| keys { | ||
| compatible = "gpio-keys"; | ||
|
|
||
| reset { | ||
| label = "reset"; | ||
| linux,code = <KEY_RESTART>; | ||
| gpios = <&gpio 22 GPIO_ACTIVE_HIGH>; | ||
| debounce-interval = <60>; | ||
| }; | ||
|
|
||
| input { | ||
| label = "input"; | ||
| linux,code = <BTN_0>; | ||
| gpios = <&gpio 16 GPIO_ACTIVE_LOW>; | ||
| debounce-interval = <60>; | ||
| }; | ||
|
|
||
| sim-tray { | ||
| label = "sim-tray"; | ||
| linux,code = <BTN_1>; | ||
| gpios = <&gpio 20 GPIO_ACTIVE_LOW>; | ||
| debounce-interval = <60>; | ||
| }; | ||
| }; | ||
|
|
||
| leds { | ||
| compatible = "gpio-leds"; | ||
| pinctrl-names = "default"; | ||
| pinctrl-0 = <&switch_led_disable_pins>; | ||
|
|
||
| led_ss0: signal-strength-0 { | ||
| label = "green:signal-strength-0"; | ||
| gpios = <&gpio 23 GPIO_ACTIVE_HIGH>; | ||
| }; | ||
|
|
||
| signal-strength-1 { | ||
| label = "green:signal-strength-1"; | ||
| gpios = <&gpio 7 GPIO_ACTIVE_HIGH>; | ||
| }; | ||
|
|
||
| signal-strength-2 { | ||
| label = "green:signal-strength-2"; | ||
| gpios = <&gpio 6 GPIO_ACTIVE_HIGH>; | ||
| }; | ||
|
|
||
| signal-strength-3 { | ||
| label = "green:signal-strength-3"; | ||
| gpios = <&gpio 26 GPIO_ACTIVE_HIGH>; | ||
| }; | ||
|
|
||
| signal-strength-4 { | ||
| label = "green:signal-strength4"; | ||
| gpios = <&gpio 27 GPIO_ACTIVE_HIGH>; | ||
| }; | ||
|
|
||
| 2g { | ||
| label = "green:2g"; | ||
| gpios = <&gpio 8 GPIO_ACTIVE_HIGH>; | ||
| }; | ||
|
|
||
| 3g { | ||
| label = "green:3g"; | ||
| gpios = <&gpio 24 GPIO_ACTIVE_HIGH>; | ||
| }; | ||
|
|
||
| lan { | ||
| label = "green:lan"; | ||
| gpios = <&gpio 14 GPIO_ACTIVE_LOW>; | ||
| /* GPIO 13 - ACTIVE HIGH for hwrev 0 */ | ||
| }; | ||
|
|
||
| wan { | ||
| label = "green:wan"; | ||
| gpios = <&gpio 17 GPIO_ACTIVE_LOW>; | ||
| /* GPIO 14 - ACTIVE HIGH for hwrev 0 */ | ||
| }; | ||
|
|
||
| /* 4G LED - GPIO21 ACTIVE_HIGH for RUT240 */ | ||
| }; | ||
|
|
||
| reg_usb_vbus: reg_usb_vbus { | ||
| compatible = "regulator-fixed"; | ||
| regulator-name = "usb_vbus"; | ||
| regulator-min-microvolt = <5000000>; | ||
| regulator-max-microvolt = <5000000>; | ||
| gpio = <&gpio 19 GPIO_ACTIVE_HIGH>; | ||
| enable-active-high; | ||
| }; | ||
| }; | ||
|
|
||
| ð0 { | ||
| status = "okay"; | ||
|
|
||
| mtd-mac-address = <&config 0x0>; | ||
| }; | ||
|
|
||
| ð1 { | ||
| status = "okay"; | ||
|
|
||
| mtd-mac-address = <&config 0x0>; | ||
| mtd-mac-address-increment = <1>; | ||
| }; | ||
|
|
||
| &spi { | ||
| status = "okay"; | ||
|
|
||
| flash@0 { | ||
| compatible = "jedec,spi-nor"; | ||
| reg = <0>; | ||
| spi-max-frequency = <30000000>; | ||
|
|
||
| partitions { | ||
| compatible = "fixed-partitions"; | ||
| #address-cells = <1>; | ||
| #size-cells = <1>; | ||
|
|
||
| partition@0 { | ||
| label = "u-boot"; | ||
| reg = <0x0 0x20000>; | ||
| read-only; | ||
| }; | ||
|
|
||
| config: partition@20000 { | ||
| label = "config"; | ||
| reg = <0x20000 0x10000>; | ||
| read-only; | ||
| }; | ||
|
|
||
| art: partition@30000 { | ||
| label = "art"; | ||
| reg = <0x30000 0x10000>; | ||
| read-only; | ||
| }; | ||
|
|
||
| partition@40000 { | ||
| compatible = "tplink,firmware"; | ||
| label = "firmware"; | ||
| reg = <0x40000 0xf30000>; | ||
| }; | ||
|
|
||
| partition@f70000 { | ||
| label = "event-log"; | ||
| reg = <0xf70000 0x90000>; | ||
| read-only; | ||
| }; | ||
| }; | ||
| }; | ||
| }; | ||
|
|
||
| &usb { | ||
| dr_mode = "host"; | ||
| vbus-supply = <®_usb_vbus>; | ||
| status = "okay"; | ||
| }; | ||
|
|
||
| &gpio { | ||
| modem-power { | ||
| gpio-hog; | ||
| output-low; | ||
| gpios = <18 GPIO_ACTIVE_HIGH>; | ||
| line-name = "modem-power"; | ||
| }; | ||
| }; | ||
|
|
||
| &usb_phy { | ||
| status = "okay"; | ||
| }; | ||
|
|
||
| &wmac { | ||
| status = "okay"; | ||
|
|
||
| mtd-cal-data = <&art 0x1000>; | ||
| mtd-mac-address = <&config 0x0>; | ||
| mtd-mac-address-increment = <2>; | ||
| }; |
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters