forked from openwrt/openwrt
Commit
This commit does not belong to any branch on this repository, and may belong to a fork outside of the repository.
ipq40xx: add MikroTik wAP ac (RBwAPG-5HacD2HnD) support
The MikroTik wAP ac (RBwAPG-5HacD2HnD) is a dual-band dual-radio 802.11ac wireless access point with integrated antenna and two Ethernet ports in a weatherproof enclosure. See https://mikrotik.com/product/wap_ac for more information. Important: this is the new ipq40xx-based wAP ac, not the older ath79-based wAP ac (RBwAPG-5HacT2HnD), already supported in OpenWrt. Specifications: - SoC: Qualcomm Atheros IPQ4018 - CPU: 4x ARM Cortex A7 - RAM: 128MB - Storage: 16MB NOR flash - Wireless - 2.4GHz: Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae - 5GHz: Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae - Ethernet: Built-in IPQ4018 (SoC, QCA8075), 2x 1000/100/10Mb/s ports, one with 802.3af/at PoE in Installation: Boot the initramfs image via TFTP, then flash the sysupgrade image using sysupgrade. Details at https://openwrt.org/toh/mikrotik/common. Notes: This preserves the MAC addresses of the physical Ethernet ports: - eth0 corresponds to the physical port labeled ETH1 and has the base MAC address. This port can be used to power the device. - eth1 corresponds to the physical port labeled ETH2 and has a MAC address one greater than the base. MAC addresses are set from /lib/preinit/05_set_iface_mac_ipq40xx.sh rather than /etc/board.d/02_network so that they are in effect for preinit. This should likely be done for other MikroTik devices and possibly other non-MikroTik devices as well. As this device has 2 physical ports, they are each connected to their respective PHYs, allowing the link status to be visible to software. Since they are not marked on the case with any role (such as LAN or WAN), both are bridged to the lan network by default, although this can easily be changed if needed. Signed-off-by: Mark Mentovai <mark@mentovai.com>
- Loading branch information
1 parent
d9ab1e5
commit 7f54bf6
Showing
8 changed files
with
250 additions
and
8 deletions.
There are no files selected for viewing
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
221 changes: 221 additions & 0 deletions
221
target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-wap-ac.dts
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| Original file line number | Diff line number | Diff line change |
|---|---|---|
| @@ -0,0 +1,221 @@ | ||
| // SPDX-License-Identifier: GPL-2.0-or-later OR MIT | ||
| /* Copyright (c) 2020, Robert Marko <robimarko@gmail.com> */ | ||
|
|
||
| #include "qcom-ipq4019.dtsi" | ||
| #include <dt-bindings/gpio/gpio.h> | ||
| #include <dt-bindings/input/input.h> | ||
| #include <dt-bindings/soc/qcom,tcsr.h> | ||
|
|
||
| / { | ||
| model = "MikroTik wAP ac"; | ||
| compatible = "mikrotik,wap-ac"; | ||
|
|
||
| memory { | ||
| device_type = "memory"; | ||
| reg = <0x80000000 0x08000000>; | ||
| }; | ||
|
|
||
| chosen { | ||
| stdout-path = "serial0:115200n8"; | ||
| }; | ||
|
|
||
| aliases { | ||
| led-boot = &led_user; | ||
| led-failsafe = &led_user; | ||
| led-running = &led_user; | ||
| led-upgrade = &led_user; | ||
| }; | ||
|
|
||
| soc { | ||
| counter@4a1000 { | ||
| compatible = "qcom,qca-gcnt"; | ||
| reg = <0x4a1000 0x4>; | ||
| }; | ||
|
|
||
| tcsr@1949000 { | ||
| compatible = "qcom,tcsr"; | ||
| reg = <0x1949000 0x100>; | ||
| qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>; | ||
| }; | ||
|
|
||
| ess_tcsr@1953000 { | ||
| compatible = "qcom,tcsr"; | ||
| reg = <0x1953000 0x1000>; | ||
| qcom,ess-interface-select = <TCSR_ESS_PSGMII>; | ||
| }; | ||
|
|
||
| tcsr@1957000 { | ||
| compatible = "qcom,tcsr"; | ||
| reg = <0x1957000 0x100>; | ||
| qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>; | ||
| }; | ||
|
|
||
| ess-switch@c000000 { | ||
| status = "okay"; | ||
| }; | ||
|
|
||
| edma@c080000 { | ||
| status = "okay"; | ||
| }; | ||
| }; | ||
|
|
||
| keys { | ||
| compatible = "gpio-keys"; | ||
|
|
||
| reset { | ||
| label = "reset"; | ||
| gpios = <&tlmm 63 GPIO_ACTIVE_LOW>; | ||
| linux,code = <KEY_RESTART>; | ||
| }; | ||
| }; | ||
|
|
||
| leds { | ||
| compatible = "gpio-leds"; | ||
|
|
||
| power { | ||
| label = "blue:power"; | ||
| gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>; | ||
| default-state = "keep"; | ||
| }; | ||
|
|
||
| led_user: user { | ||
| label = "green:user"; | ||
| gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>; | ||
| panic-indicator; | ||
| }; | ||
| }; | ||
| }; | ||
|
|
||
| &prng { | ||
| status = "okay"; | ||
| }; | ||
|
|
||
| &tlmm { | ||
| serial_pins: serial_pinmux { | ||
| mux { | ||
| pins = "gpio60", "gpio61"; | ||
| function = "blsp_uart0"; | ||
| bias-disable; | ||
| }; | ||
| }; | ||
|
|
||
| spi_0_pins: spi_0_pinmux { | ||
| pin { | ||
| function = "blsp_spi0"; | ||
| pins = "gpio55", "gpio56", "gpio57"; | ||
| drive-strength = <2>; | ||
| bias-disable; | ||
| }; | ||
| pin_cs { | ||
| function = "gpio"; | ||
| pins = "gpio54"; | ||
| drive-strength = <2>; | ||
| bias-disable; | ||
| output-high; | ||
| }; | ||
| }; | ||
| }; | ||
|
|
||
| &blsp_dma { | ||
| status = "okay"; | ||
| }; | ||
|
|
||
| &blsp1_spi1 { | ||
| status = "okay"; | ||
|
|
||
| pinctrl-0 = <&spi_0_pins>; | ||
| pinctrl-names = "default"; | ||
| cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>; | ||
|
|
||
| flash@0 { | ||
| reg = <0>; | ||
| compatible = "jedec,spi-nor"; | ||
| spi-max-frequency = <40000000>; | ||
|
|
||
| partitions { | ||
| compatible = "fixed-partitions"; | ||
| #address-cells = <1>; | ||
| #size-cells = <1>; | ||
|
|
||
| partition@0 { | ||
| label = "Qualcomm"; | ||
| reg = <0x0 0x80000>; | ||
| read-only; | ||
| }; | ||
|
|
||
| partition@80000 { | ||
| compatible = "mikrotik,routerboot-partitions"; | ||
| #address-cells = <1>; | ||
| #size-cells = <1>; | ||
| label = "RouterBoot"; | ||
| reg = <0x80000 0x80000>; | ||
|
|
||
| hard_config { | ||
| read-only; | ||
| size = <0x2000>; | ||
| }; | ||
|
|
||
| dtb_config { | ||
| read-only; | ||
| }; | ||
|
|
||
| soft_config { | ||
| }; | ||
| }; | ||
|
|
||
| partition@100000 { | ||
| compatible = "mikrotik,minor"; | ||
| label = "firmware"; | ||
| reg = <0x100000 0xf00000>; | ||
| }; | ||
| }; | ||
| }; | ||
| }; | ||
|
|
||
| &blsp1_uart1 { | ||
| status = "okay"; | ||
|
|
||
| pinctrl-0 = <&serial_pins>; | ||
| pinctrl-names = "default"; | ||
| }; | ||
|
|
||
| &cryptobam { | ||
| status = "okay"; | ||
| }; | ||
|
|
||
| &crypto { | ||
| status = "okay"; | ||
| }; | ||
|
|
||
| &watchdog { | ||
| status = "okay"; | ||
| }; | ||
|
|
||
| &mdio { | ||
| status = "okay"; | ||
| }; | ||
|
|
||
| &gmac0 { | ||
| qcom,phy_mdio_addr = <4>; | ||
| qcom,poll_required = <1>; | ||
| qcom,forced_speed = <1000>; | ||
| qcom,forced_duplex = <1>; | ||
| vlan_tag = <2 0x20>; | ||
| }; | ||
|
|
||
| &gmac1 { | ||
| qcom,phy_mdio_addr = <3>; | ||
| vlan_tag = <1 0x10>; | ||
| }; | ||
|
|
||
| &wifi0 { | ||
| status = "okay"; | ||
|
|
||
| qcom,ath10k-calibration-variant = "MikroTik-wAP-ac"; | ||
| }; | ||
|
|
||
| &wifi1 { | ||
| status = "okay"; | ||
|
|
||
| qcom,ath10k-calibration-variant = "MikroTik-wAP-ac"; | ||
| }; |
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters