mvebu: add support for Buffalo LinkStation LS421DE

Buffalo LinkStation LS421DE is a dual bay NAS, based on Marvell Armada 370

Hardware:
   SoC:         Marvell Armada 88F6707-A1
   CPU:         Cortex-A9 1200 MHz, 1 core
   Flash:       SPI-NOR 1 MiB, NAND 512 MiB
   RAM:         DDR3 512 MiB
   Ethernet:    1x 10/100/1000 Mbps
   USB:         1x 2.0, 1x 3.0
   SATA:        2x 3.0 Gbps
   LEDs/Input : 5x / 2x (1x button, 1x slide-switch)
   RTC:         Ricoh RS5C372A, I2C, no battery

Flash instruction (UART+TFTP):
  1. Downgrade the OEM firmware to 1.34 version (BUFFALO_BOOTVER=0.13)
  2. Remove any hard drive from inside the bays.
  3. Boot the Openwrt initramfs image using the U-Boot serial console:
         tftpboot 0x1200000 buffalo_ls421de-initramfs-kernel.bin
         bootm 0x1200000
  4. Flash the sysupgrade image using the Openwrt console:
         sysupgrade -n buffalo_ls421de-squashfs-sysupgrade.bin
  5. Wait until it finish, the device will reboot with Openwrt installed
     on the NAND flash.

Note:
  - Device shuting down doesn't work, even if the power slide switch is
    used. We must first, via MDIO, set the unused LED2 at the ethernet
    phy0 to off state. Reboot works ok.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>

target/linux/mvebu/cortexa9/base-files/lib/preinit/06_set_iface_mac

@@ -9,6 +9,10 @@ preinit_set_mac_address() {
 	. /lib/functions.sh
 
 	case $(board_name) in
+	buffalo,ls421de)
+		mac=$(mtd_get_mac_ascii u-boot-env eth1addr)
+		ip link set dev eth0 address $mac 2>/dev/null
+		;;
 	linksys,caiman|linksys,cobra|linksys,rango|linksys,shelby|linksys,venom)
 		# rename interfaces back to the way they were with 4.4
 		case "$(readlink /sys/class/net/eth0)" in

target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh

@@ -22,6 +22,9 @@ platform_check_image() {
 
 platform_do_upgrade() {
 	case "$(board_name)" in
+	buffalo,ls421de)
+		nand_do_upgrade "$1"
+		;;
 	cznic,turris-omnia|\
 	solidrun,clearfog-base-a1|\
 	solidrun,clearfog-pro-a1)

target/linux/mvebu/files-4.19/arch/arm/boot/dts/armada-370-buffalo-ls421de.dts

@@ -0,0 +1,360 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for Buffalo LinkStation LS421DE
+ *
+ * Copyright (C) 2020 Daniel González Cabanelas <dgcbueu@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "armada-370.dtsi"
+#include "mvebu-linkstation-fan.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Buffalo LinkStation LS421DE";
+	compatible = "buffalo,ls421de", "marvell,armada370", "marvell,armada-370-xp";
+
+	aliases {
+		led-boot = &led_boot;
+		led-failsafe = &led_failsafe;
+		led-running = &led_power;
+		led-upgrade = &led_upgrade;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlyprintk noinitrd rootfstype=squashfs";
+		stdout-path = "serial0:115200n8";
+		append-rootblock = "nullparameter="; /* override the bootloader args */
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>; /* 512 MB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000
+			  MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000
+			  MBUS_ID(0x09, 0x01) 0 0xf1100000 0x10000>;
+	};
+
+	gpio_fan {
+		gpios = <&gpio0 13 GPIO_ACTIVE_HIGH
+			&gpio0 14 GPIO_ACTIVE_HIGH>;
+		alarm-gpios = <&gpio0 10 GPIO_ACTIVE_HIGH>;
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&pmx_hdd_present &pmx_buttons>;
+		pinctrl-names = "default";
+
+		hdd1-present {
+			label = "HDD1 Present";
+			linux,code = <KEY_PROG1>;
+			gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
+		};
+
+		hdd2-present {
+			label = "HDD2 Present";
+			linux,code = <KEY_PROG2>;
+			gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+
+		};
+
+		power {
+			label = "Power Switch";
+			linux,code = <KEY_POWER>;
+			linux,input-type = <EV_SW>;
+			gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
+		};
+
+		function {
+			label = "Function Button";
+			linux,code = <KEY_OPTION>;
+			gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio_leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmx_leds1 &pmx_leds2>;
+
+		system_red {
+			label = "ls421de:red:system";
+			gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		led_power: power_white {
+			label = "ls421de:white:power";
+			gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		led_failsafe: power_red {
+			label = "ls421de:red:power";
+			gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
+		};
+
+		led_upgrade: power_orange {
+			label = "ls421de:orange:power";
+			gpios = <&gpio1 25 GPIO_ACTIVE_HIGH>;
+		};
+
+		led_boot: system_white {
+			label = "ls421de:white:system";
+			gpios = <&gpio1 27 GPIO_ACTIVE_HIGH>;
+		};
+
+		hdd1_red {
+			label = "ls421de:red:hdd1";
+			gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+			linux,default-trigger = "disk-activity";
+		};
+
+		hdd2_red {
+			label = "ls421de:red:hdd2";
+			gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+			linux,default-trigger = "disk-activity";
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&pmx_power_usb &pmx_power_hdd1 &pmx_power_hdd2>;
+
+		pinctrl-names = "default";
+
+		usb_v5_regulator: usb-v5-regulator {
+			compatible = "regulator-fixed";
+			regulator-name = "USB";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+		};
+
+		ata1_regulator: ata1-regulator {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "HDD1";
+			regulator-min-microvolt = <12000000>;
+			regulator-max-microvolt = <12000000>;
+			startup-delay-us = <2000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		ata2_regulator: ata2-regulator {
+			compatible = "regulator-fixed";
+			reg = <2>;
+			regulator-name = "HDD2";
+			regulator-min-microvolt = <12000000>;
+			regulator-max-microvolt = <12000000>;
+			startup-delay-us = <4000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 9 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	/* FIXME: this driver needs to be aware of the LED2 eth phy use,
+	   which must be set to off state before shutting down the machine */
+	restart_poweroff {
+		compatible = "restart-poweroff";
+	};
+};
+
+&eth1 {
+	pinctrl-0 = <&ge1_rgmii_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	phy = <&phy0>;
+	phy-mode = "rgmii-id";
+};
+
+&i2c0 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	rs5c372a: rs5c372a@32 {
+		compatible = "ricoh,rs5c372a";
+		reg = <0x32>;
+	};
+};
+
+&mdio {
+	pinctrl-0 = <&mdio_pins>;
+	pinctrl-names = "default";
+
+	phy0: ethernet-phy@0 { /* Marvell 88E1518 */
+		reg = <0>;
+		/* LED2 is used to inform uBoot if the power-switch was slided
+		   to the "off" position, and then power off the machine.
+		   Page 0x3, Register 0x10, bit 8:
+				0x800: LED2 off, power off the machine
+				0x900: LED2 on, boot the machine */
+		marvell,reg-init = <0x3 0x10 0x1 0x1991>, /* LED Function */
+					<0x3 0x11 0x1 0x4401>, /* LED polarity */
+					<0x3 0x12 0x1 0x4905>; /* LED Timer */
+	};
+};
+
+&pciec {
+	status = "okay";
+	/* Connected to uPD720202 USB 3.0 Host */
+	pcie@1,0 {
+		status = "okay";
+	};
+};
+
+&pmsu {
+	pinctrl-0 = <&pmx_power_cpu>;
+	pinctrl-names = "default";
+};
+
+&rtc {
+	status = "disabled";
+};
+
+&sata {
+	nr-ports = <2>;
+	status = "okay";
+};
+
+&sdio {
+	pinctrl-0 = <&sdio_pins2>;
+	pinctrl-names = "default";
+	status = "okay";
+	/* No CD or WP GPIOs */
+	broken-cd;
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&nand_controller {
+	status = "okay";
+
+	nand@0 {
+		reg = <0>;
+		label = "pxa3xx_nand-0";
+		nand-rb = <0>;
+		marvell,nand-keep-config;
+		nand-on-flash-bbt;
+		nand-ecc-strength = <4>;
+		nand-ecc-step-size = <512>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "kernel";
+				reg = <0x00000000 0x02000000>;  /* 32 MiB */
+			};
+
+			partition@2000000 {
+				label = "ubi";
+				reg = <0x02000000 0x1e000000>;  /* 480 MiB */
+			};
+		};
+	};
+};
+
+&spi0 {
+	status = "okay";
+	pinctrl-0 = <&spi0_pins2>;
+	pinctrl-names = "default";
+
+	spi-flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "mxicy,mx25l8005", "jedec,spi-nor";
+		reg = <0>; /* Chip select 0 */
+		spi-max-frequency = <50000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				reg = <0x00000 0xf0000>; /* 960 KiB*/
+				label = "u-boot";
+				read-only;
+			};
+			partition@f0000 {
+				reg = <0xf0000 0x10000>; /* 64 KiB */
+				label = "u-boot-env";
+			};
+		};
+	};
+};
+
+&pinctrl {
+	pmx_power_cpu: pmx-power-cpu {
+		marvell,pins = "mpp4";
+		marvell,function = "vdd";
+	};
+	pmx_power_usb: pmx-power-usb {
+		marvell,pins = "mpp5";
+		marvell,function = "gpo";
+	};
+	pmx_power_hdd1: pmx-power-hdd1 {
+		marvell,pins = "mpp8";
+		marvell,function = "gpio";
+	};
+	pmx_power_hdd2: pmx-power-hdd2 {
+		marvell,pins = "mpp9";
+		marvell,function = "gpo";
+	};
+	pmx_fan_lock: pmx-fan-lock {
+		marvell,pins = "mpp10";
+		marvell,function = "gpio";
+	};
+	pmx_hdd_present: pmx-hdd-present {
+		marvell,pins = "mpp11", "mpp12";
+		marvell,function = "gpio";
+	};
+	pmx_fan_high: pmx-fan-high {
+		marvell,pins = "mpp13";
+		marvell,function = "gpio";
+	};
+	pmx_fan_low: pmx-fan-low {
+		marvell,pins = "mpp14";
+		marvell,function = "gpio";
+	};
+	pmx_buttons: pmx-buttons {
+		marvell,pins = "mpp15", "mpp16";
+		marvell,function = "gpio";
+	};
+	pmx_leds1: pmx-leds {
+		marvell,pins = "mpp7", "mpp54", "mpp59", "mpp61";
+		marvell,function = "gpo";
+	};
+	pmx_leds2: pmx-leds {
+		marvell,pins = "mpp55", "mpp57", "mpp62";
+		marvell,function = "gpio";
+	};
+};