Other devices #2
Comments
Redmi AX6CDT-1G.zip for backup only. |
pexcn
pushed a commit
that referenced
this issue
Jan 10, 2024
Hardware specification: SoC: MediaTek MT7981B 2x A53 Flash: 16MB NOR RAM: 256MB Ethernet: 2x 10/100/1000 Mbps Switch: MediaTek MT7531AE WiFi: MediaTek MT7976C Button: Reset Power: DC 12V 1A, PoE 802.3af 48V Flash instructions: Option #1 - SSH I was able to SSH into the stock firmware of my device. 1. Attach the router to the network 2. Use scp (-O) to copy the sysupgrade image 3. Connect using SSH and run `sysupgrade -n` Option #2 - U-Boot One way to use the bootloader for flashing is using TFTP: 1. Connect to the router using an ethernet cable 2 Spin up a TFTP server serving the sysupgrade file 3. Open the case and attach a UART 4. Attach power to the router and interrupt the countdown by pressing any key 5. Select option #2 (Upgrade firmware) 6. Enter IP address information and image name 7. Wait patiently Co-Authored-By: Enrique Rodríguez Valencia <enrique.rodriguez@galgus.net> Co-Authored-By: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
pexcn
pushed a commit
that referenced
this issue
Mar 2, 2024
Disabled services should be kept disabled after sysupgrade. This can be easily handled using a proper uci-defaults script. Extend sysupgrade to check for disabled services, generate uci-defaults script disabling them and include it in backup. Cc: Christian Marangi <ansuelsmth@gmail.com> Cc: Jo-Philipp Wich <jo@mein.io> Cc: Jonas Gorski <jonas.gorski@gmail.com> Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Jo-Philipp Wich <jo@mein.io>
pexcn
pushed a commit
that referenced
this issue
Jun 11, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jun 11, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jun 11, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jun 11, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jun 18, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jun 18, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jul 5, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jul 10, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jul 10, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jul 11, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jul 12, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jul 12, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jul 20, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jul 20, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jul 24, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
pexcn
pushed a commit
that referenced
this issue
Jul 24, 2024
QSDK NSS builds utilize skbuff recycling for better handling of memory.
On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.
BEFORE:
echo 3 >! /proc/sys/vm/drop_caches
free -m
total used free shared buff/cache available
Mem: 867 338 547 90 101 528
Swap: 0 0 0
AFTER:
total used free shared buff/cache available
Mem: 867 242 594 1 81 624
Swap: 0 0 0
NOTE:
For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.
1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.
2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'
3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch
And re-test with #1 and #2
It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.
ath11k_nss: fix typo in 512M memory profile
ath11k_nss: remove SFE patch 718-e-mac80211-Deliver-the-frame-to-driver-tx-ops-directly
It is not relevant to NSS builds and only meant for SFE.
ath11k_nss: remove unecessary patches
Color collision should be left on by default, as it's a primary feature
of 802.11AX.
ath11k_nss: fix spacing
ath11k_nss: Remove unnecessary TKIP bloat
Remove TKIP patches that are not being used as 99% of folks are running
modern encryption (AES-CCMP,SAE,etc).
ath11k_nss: parameterize DP_RXDMA_REFILL_RING_SIZE memory profile
ath11k_nss: Remove SFE related code
Cleanup SFE (shortcut fe) related code as we're not using it on NSS
ath11k_nss: idr, ampdu, and skb headroom check optimizations
ath11k_nss: get valid last_rate for rx_bitrate from cpu stats
ath11k_nss: Fix BCCA counter for EMA
Currently BCCA counter is updated to FW via csa counter offs and
beacon with new countdown is updated for every beacon tx completion event.
For EMA, all EMA beacons are updated in one shot, and counter update for
every tx event will mess up the actual sequence of countdown sent over the air.
Allow FW to update the countdown till 1 and finalize the color
change.
ath11k_nss: Fix compile for TRACE feature
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
Redmi AX5 JDCloud
0001-base-files-add-eMMC-sysupgrade-support.patch
0002-ipq60xx-add-redmi-ax5-jdcloud-support.patch
0003-ipq60xx-fix-ax5-jdcloud-support.patch
0004-ipq60xx-set-DEVICE_DTS-for-redmi-ax5-jdcloud.patch
The text was updated successfully, but these errors were encountered: