ramips: add support for ipTIME AX2004M

ipTIME AX2004M is an 802.11ax (Wi-Fi 6) router, based on MediaTek
MT7621A.

Specifications:
* SoC: MT7621A
* RAM: 256 MiB
* Flash: NAND 128 MiB
* Wi-Fi:
  * MT7915D: 2.4/5 GHz (DBDC)
* Ethernet: 5x 1GbE
  * Switch: SoC built-in
* USB: 1x 3.0
* UART: J4 (115200 baud)
  * Pinout: [3V3] (TXD) (RXD) (GND)

MAC addresses:

| interface |    MAC address    |     source     | comment
|-----------|-------------------|----------------|---------
|       LAN | 58:xx:xx:00:xx:9B |                | [1]
|       WAN | 58:xx:xx:00:xx:99 |                |
|   WLAN 2G | 58:xx:xx:00:xx:98 | factory 0x4    |
|   WLAN 5G | 5A:xx:xx:40:xx:98 |                |
|           | 58:xx:xx:00:xx:98 | config ethaddr |

[1] Used in this patch as WLAN 5G MAC address with the local bit set

Load addresses:
* stock
  * 0x80010000: FIT image
  * 0x81001000: kernel image -> entry
* OpenWrt
  * 0x80010000: FIT image
  * 0x82000000: uncompressed kernel+relocate image
  * 0x80001000: relocated kernel image -> entry

Notes:
* This device has a dual-boot partition scheme, but this firmware works
  only on boot partition 1. The stock web interface will flash only on the
  inactive boot partition, but the recovery web page will always flash on
  boot partition 1.

Installation via recovery mode:
1.  Press reset button, power up the device, wait >10s for CPU LED
    to stop blinking.
2.  Upload recovery image through the recovery web page at 192.168.0.1.

Revert to stock firmware:
1.  Install stock image via recovery mode.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>

include/image-commands.mk

@@ -295,6 +295,11 @@ define Build/install-dtb
 	)
 endef
 
+define Build/iptime-crc32
+	$(STAGING_DIR_HOST)/bin/iptime-crc32 $(1) $@ $@.new
+	mv $@.new $@
+endef
+
 define Build/iptime-naspkg
 	$(STAGING_DIR_HOST)/bin/iptime-naspkg $(1) $@ $@.new
 	mv $@.new $@

target/linux/ramips/dts/mt7621_iptime_ax2004m.dts

@@ -0,0 +1,165 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	compatible = "iptime,ax2004m", "mediatek,mt7621-soc";
+	model = "ipTIME AX2004M";
+
+	aliases {
+		led-boot = &led_cpu;
+		led-failsafe = &led_cpu;
+		led-running = &led_cpu;
+		led-upgrade = &led_cpu;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_cpu: cpu {
+			label = "amber:cpu";
+			gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+		};
+
+		wlan2g {
+			label = "amber:wlan2g";
+			gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0radio";
+		};
+
+		wlan5g {
+			label = "amber:wlan5g";
+			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy1radio";
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+};
+
+&nand {
+	status = "okay";
+
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "u-boot";
+			reg = <0x0 0x80000>;
+			read-only;
+		};
+
+		partition@80000 {
+			label = "config";
+			reg = <0x80000 0x80000>;
+			read-only;
+		};
+
+		factory: partition@100000 {
+			label = "factory";
+			reg = <0x100000 0x80000>;
+			read-only;
+
+			compatible = "nvmem-cells";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			macaddr_factory_4: macaddr@4 {
+				reg = <0x4 0x6>;
+			};
+		};
+
+		partition@180000 {
+			label = "firmware";
+			reg = <0x180000 0x7680000>;
+
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "kernel";
+				reg = <0x0 0x400000>;
+			};
+
+			partition@400000 {
+				label = "ubi";
+				reg = <0x400000 0x7280000>;
+			};
+		};
+	};
+};
+
+&state_default {
+	gpio {
+		groups = "i2c", "jtag", "wdt";
+		function = "gpio";
+	};
+};
+
+&gmac0 {
+	nvmem-cells = <&macaddr_factory_4>;
+	nvmem-cell-names = "mac-address";
+	mac-address-increment = <3>;
+};
+
+&switch0 {
+	ports {
+		port@0 {
+			status = "okay";
+			label = "wan";
+			nvmem-cells = <&macaddr_factory_4>;
+			nvmem-cell-names = "mac-address";
+			mac-address-increment = <1>;
+		};
+
+		port@1 {
+			status = "okay";
+			label = "lan4";
+		};
+
+		port@2 {
+			status = "okay";
+			label = "lan3";
+		};
+
+		port@3 {
+			status = "okay";
+			label = "lan2";
+		};
+
+		port@4 {
+			status = "okay";
+			label = "lan1";
+		};
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&pcie1 {
+	wifi@0,0 {
+		compatible = "mediatek,mt76";
+		reg = <0x0000 0 0 0 0>;
+		mediatek,mtd-eeprom = <&factory 0x0>;
+	};
+};

target/linux/ramips/image/mt7621.mk

@@ -817,6 +817,26 @@ define Device/iptime_a8004t
 endef
 TARGET_DEVICES += iptime_a8004t
 
+define Device/iptime_ax2004m
+  $(Device/dsa-migration)
+  BLOCKSIZE := 128k
+  PAGESIZE := 2048
+  KERNEL_SIZE := 4096k
+  IMAGE_SIZE := 121344k
+  UBINIZE_OPTS := -E 5
+  KERNEL_LOADADDR := 0x82000000
+  KERNEL := kernel-bin | relocate-kernel 0x80001000 | lzma | \
+	fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
+  IMAGES += recovery.bin
+  IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+  IMAGE/recovery.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
+	check-size | iptime-crc32 ax2004m
+  DEVICE_VENDOR := ipTIME
+  DEVICE_MODEL := AX2004M
+  DEVICE_PACKAGES := kmod-mt7915e kmod-usb3
+endef
+TARGET_DEVICES += iptime_ax2004m
+
 define Device/iptime_t5004
   $(Device/dsa-migration)
   BLOCKSIZE := 128k

target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac

@@ -25,6 +25,12 @@ case "$board" in
 		[ "$PHYNBR" = "1" ] && \
 			macaddr_add "$(mtd_get_mac_binary factory 0x4)" 1 > /sys${DEVPATH}/macaddress
 		;;
+	iptime,ax2004m)
+		if [ "$PHYNBR" = "1" ]; then
+			hw_mac_addr="$(mtd_get_mac_binary factory 0x4)"
+			macaddr_setbit_la "$(macaddr_add $hw_mac_addr 3)" > /sys${DEVPATH}/macaddress
+		fi
+		;;
 	jcg,q20)
 		[ "$PHYNBR" = "1" ] && \
 			macaddr_setbit_la "$(mtd_get_mac_binary Factory 0x4)" > /sys${DEVPATH}/macaddress

target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh

@@ -59,6 +59,7 @@ platform_do_upgrade() {
 	dlink,dir-853-a3|\
 	hiwifi,hc5962|\
 	iptime,a3004t|\
+	iptime,ax2004m|\
 	iptime,t5004|\
 	jcg,q20|\
 	linksys,e5600|\