NOTE: this is a fork of the work of various people who did 99% of the work. I just did some cleanups, translated to english and fixed various bugs.
Emulates Hörmann UAP1-HCP board using an ESP32 and a RS485 converter, and exposes garage door controls over web page and MQTT.
Compatible with the following motors (UAP1-HCP / HCP2-Bus / Modbus):
- SupraMatic E/P Serie 4
- ProMatic Serie 4
It is not compatible with E3 series motors. Previous generations have different protocol, different pin layout, and already have another supporting project.
- Get current status (door open/close/position, light on/off)
- Trigger the actions
- light on/off
- gate open, close, stop
- gate position: half, ventilation, custom (MQTT set_position compatible)
- Web Interface
- Web Service (GET)
- OTA Update (with username and password)
- AsyncWifiManger (hotspot when disconnected)
- DS18X20 or BME280 sensor (with threshold)
- Efficient MQTT messages (send only MQTT Message if Door state changed)
- Open command requires two clicks. A feature? :)
- On Promatic4 (at least) the status led of the motor blinks red.
Eigentlich war das Ziel, die Steuerung komplett nur mit einem ESP8266 zu realisieren, allerdings gibt es durch die WLAN und TCP/IP-Stackumsetzung Timeoutprobleme, die zum Verbindungsabbruch zwischen dem Antrieb und der Steuerung führen können. Durch die ISR-Version konnte das Problem zwar reduziert aber nicht komplett ausgeschlossen werden. Daher gibt es zwei weitere Versionen, die bisher stabil laufen. Eine Variante nutzt den ESP32 statt ESP8266, welcher über 2 Kerne verfügt und so scheinbar besser mit WLAN-Verbindungsproblemen zurecht kommt. Die andere Option ist ein zweiter MCU, der die MODBUS Simulation übernimmt, sodass sich der ESP8266 nur noch um die Netzwerkkommunikation und das WebInterface kümmern muss.
http://[deviceip]
http://[deviceip]/command?action=[id]
| id | Function | Other Parameters |
|---|---|---|
| 0 | Close | |
| 1 | Open | |
| 2 | Stop | |
| 3 | Ventilation | |
| 4 | Half Open | |
| 5 | Light toggle | |
| 6 | Restart | |
| 7 | Set Position | position=[0-100] |
http://[deviceip]/status
Response (JSON)
{
"valid" : true,
"doorstate" : 1,
"doorposition" : 0,
"doortarget" : 0,
"lamp" : true,
"debug" : 0,
"lastresponse" : 0
}
http://[deviceip]/sysinfo
http://[deviceip]/update
- GND (Blue)
- GND (Yellow)
- B- (Green)
- A+ (Red)
- +24V (Black)
- +24V (White)
Pins A+ (Red) and B- (Green) need a 120 Ohm resistor for BUS termination. Some RS485 adapters provide termination pad to be soldered.
DS18X20 connected to GPIO4.
ESP32 powering requires a Step Down Module such as LM2596S DC-DC, but any 24VDC ==> 5VDC will do, even the tiny ones with 3 pin. Please note that the suggested serial pins for serial interfacing, on ESP32, are 16 RXD and 17 TXD.
It is possible to implement it with protoboard and underside soldering:
Body with optional BME280 Sensor
Lid
- Connect the board to the BUS
- Run a BUS scan:
- Old HW-Version / Promatic4: BUS scan is started through flipping (ON - OFF) last dip switch. Note that BUS power (+24v) is removed when no devices are detected. In case of issues, you may find useful to "jump start" the device using the +24V provision of other connectors of the motor control board.
- New HW version: with newer HW versions, the bus scan is carried out using the LC display in menu 37. For more see: Supramatic 4 Busscan
This is just a quick and dirty implementation and needs refactoring, but it is working. Using the Shutter Custom Card (from HACS) it is also possible to get a representation of the current position of the door, and slide it to custom position (through set_position MQTT command).
