-
Notifications
You must be signed in to change notification settings - Fork 3
New issue
Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.
By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.
Already on GitHub? Sign in to your account
Flashing Robotdyn ESP8266-pro... #1
Comments
The docs say the ESP8266 has 3 boot modes. Normal (from flash), programming mode and boot from SD. Ignore the last one. The pins configuration is described well here.
https://zoetrope.io/tech-blog/esp8266-bootloader-modes-and-gpio-state-startup
I think for SPI you need to hook up to pin 15 so you need to pull up with a resistor (I'll confirm when I get home) to make both work.
…--
Reza
On Mar 11, 2017, at 2:55 PM, cookins ***@***.***> wrote:
Hey
Found your answer on Google about flashing that Robotdyn esp8266 pro.
Can't find any documentation about it...
Can you please tell me, how you connect pins to arduino? I have my own firmware from http://wifi-iot.com/p/esp8266/
But in this hub said that you uploading some sketches to arduino... I thought it's need to put arduino in boot mode with rst+grn?
—
You are receiving this because you are subscribed to this thread.
Reply to this email directly, view it on GitHub, or mute the thread.
|
Hey, I just checked and GPIO15 should be pulled down via a 4k or 10k
resistor. The rest of the wiring is in the Readme page:
https://github.com/rpakdel/esp8266-pro-i2c-spi/blob/master/README.md
…On Sat, Mar 11, 2017 at 5:35 PM, Reza Pakdel ***@***.***> wrote:
The docs say the ESP8266 has 3 boot modes. Normal (from flash),
programming mode and boot from SD. Ignore the last one. The pins
configuration is described well here.
https://zoetrope.io/tech-blog/esp8266-bootloader-modes-and-
gpio-state-startup
I think for SPI you need to hook up to pin 15 so you need to pull up with
a resistor (I'll confirm when I get home) to make both work.
--
Reza
On Mar 11, 2017, at 2:55 PM, cookins ***@***.***> wrote:
Hey
Found your answer on Google about flashing that Robotdyn esp8266 pro.
Can't find any documentation about it...
Can you please tell me, how you connect pins to arduino? I have my own
firmware from http://wifi-iot.com/p/esp8266/
But in this hub said that you uploading some sketches to arduino... I
thought it's need to put arduino in boot mode with rst+grn?
—
You are receiving this because you are subscribed to this thread.
Reply to this email directly, view it on GitHub
<#1>, or mute the
thread
<https://github.com/notifications/unsubscribe-auth/AFlygoqSGhYaS5WKZZ6jABQiUnb0fwtUks5rkyZ2gaJpZM4MaXU6>
.
--
Reza Pakdel
|
Thanks |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
Hey
Found your answer on Google about flashing that Robotdyn esp8266 pro.
Can't find any documentation about it...
Can you please tell me, how you connect pins to arduino? I have my own firmware from http://wifi-iot.com/p/esp8266/
But in this hub said that you uploading some sketches to arduino... I thought it's need to put arduino in boot mode with rst+grn?
The text was updated successfully, but these errors were encountered: