data_array #31
Replies: 13 comments 11 replies
-
以前老版本有一个字符串查询并且输出的控件,我可以从一个字符串中取出某个(段)字符。 问题: |
Beta Was this translation helpful? Give feedback.
-
hi,Mr. Ruan. |
Beta Was this translation helpful? Give feedback.
-
来交作业了 |
Beta Was this translation helpful? Give feedback.
-
a new question came up |
Beta Was this translation helpful? Give feedback.
-
用校园网和自己手机热点都打不开
990352597
***@***.***
…------------------ 原始邮件 ------------------
发件人: ***@***.***>;
发送时间: 2022年12月10日(星期六) 晚上9:40
收件人: ***@***.***>;
抄送: ***@***.***>; ***@***.***>;
主题: Re: [ruanqizhen/labview_book] data_array (Discussion #31)
我这边可以正常打开,检查一下网络叭
—
Reply to this email directly, view it on GitHub, or unsubscribe.
You are receiving this because you commented.Message ID: ***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
关于显示sin的强度图的问题: |
Beta Was this translation helpful? Give feedback.
-
确实是用混了,感谢。
雷秦
***@***.***
…------------------ 原始邮件 ------------------
发件人: ***@***.***>;
发送时间: 2023年1月14日(星期六) 晚上10:21
收件人: ***@***.***>;
抄送: ***@***.***>; ***@***.***>;
主题: Re: [ruanqizhen/labview_book] data_array (Discussion #31)
我估计你用的是“强度图表”(Intensity Chart)控件,所以无法修改 x 范围。“强度图”(Intensity Graph)控件是很容易设置 x 坐标的。这两个控件类似,容易搞混。图形化显示数据一节会介绍这两种控件的区别。
—
Reply to this email directly, view it on GitHub, or unsubscribe.
You are receiving this because you commented.Message ID: ***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
感谢,两种方式都成功实现
雷秦
***@***.***
…------------------ 原始邮件 ------------------
发件人: ***@***.***>;
发送时间: 2023年1月14日(星期六) 晚上10:26
收件人: ***@***.***>;
抄送: ***@***.***>; ***@***.***>;
主题: Re: [ruanqizhen/labview_book] data_array (Discussion #31)
“强度图表”(Intensity Chart)控件也可以设置 x 坐标长度,但是要先改图表历史长度(Chart History Length),再改 x 坐标最大最小范围。
—
Reply to this email directly, view it on GitHub, or unsubscribe.
You are receiving this because you commented.Message ID: ***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
在做for循环第一个例子时摸索出来几点经验分享一下:注意运行前路径输入控件不能为空,不然会出现报错“错误8发生于 Recursive File List.vi-”;因为是想打开一个文件夹,所以可以右键路径输入控件属性,将浏览选项-选择模式-文件夹勾选;进度条的属性标尺的最大值改为1,不然进度条会看起来没有动。 |
Beta Was this translation helpful? Give feedback.
-
想请问最后一个例子,在我高亮执行过程后就出现13和245的结果,我也尝试在其中一个循环里加了一个1s延时后结果变成了15(加延时)和234(没加)。是不是两个for循环因为并行,所以最终的结果会受哪个循环跑的快,跑的快的一边就会更频繁使用子VI里移位寄存器的结果? |
Beta Was this translation helpful? Give feedback.
-
您好,在节“簇数据运算”的第二段话末尾“还可以前后两个簇中元素顺序不一致等引发的错误”处存在语法错误,应在“可以”后面添加“避免”、“防止”一类的词汇。 |
Beta Was this translation helpful? Give feedback.
-
在“数组”的“输出通道”第三条“Concatening”处,文尾的“每一次循环迭代传递给隧道会被附加的数组的后面”表意不清,应修改为类似“每一次循环迭代传递给隧道会被添加在对应输出内容的后面”的表述。 |
Beta Was this translation helpful? Give feedback.
-
您好,在节“移位寄存器”中的“改进后的程序”字样下的第二段文尾“除非能够确定程序的不需要给移位寄存器赋初值”应该为“除非能够确定程序的确不需要给移位寄存器赋初值”。 |
Beta Was this translation helpful? Give feedback.
-
数组和循环结构
https://lv.qizhen.xyz/data_array
Beta Was this translation helpful? Give feedback.
All reactions