Replies: 18 comments 1 reply
-
The Nuki app is standby for any possible firmware updates, but other than that the NUKI is indeed used through nuki_hub only (through mqtt/ domotica software). Works flawlessly. |
Beta Was this translation helpful? Give feedback.
-
ok so how could we handle the bluetooth authtentication in this scenario without the Nuki app? using the HASS state for each person? |
Beta Was this translation helpful? Give feedback.
-
I do not follow what you mean. The bridge is connected/authenticated to the lock through bluetooth (as only device). The bridge has now become your primary interface (through MQTT). How you deal with e.g. multi-users, the ability to see the locked status and/or (un)lock at different times has now shifted to your domotica software. I do not us HASS (but Openhab), but elaborating on this might be better done on a HASS forum I guess. |
Beta Was this translation helpful? Give feedback.
-
Yes indeed "How you deal with e.g. multi-users, the ability to see the locked status and/or (un)lock at different times has now shifted to your domotica software." And so you asked to my question, you're using the ability of the domotica software to unlock or lock the nuki based on certain event. Got it. so @bartsnijder are you using the nuki without the nuki app at all on your setup? |
Beta Was this translation helpful? Give feedback.
-
In the daily setup: no I do not use the NUKI app. |
Beta Was this translation helpful? Give feedback.
-
ok thanks for the clarification!
Roberto Viola
Software engineer and open source enthusiast
http://robertoviola.cloud
Il giorno mar 23 gen 2024 alle 12:08 bartsnijder ***@***.***>
ha scritto:
… In the daily setup: no I do not use the NUKI app.
But I do have the app standby for possible firmware updates.
—
Reply to this email directly, view it on GitHub
<#274 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AAALYWEYE4TGXHA4A3M2P6DYP6K3DAVCNFSM6AAAAABCGNCCVGVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTSMBVHAYTENJUG4>
.
You are receiving this because you authored the thread.Message ID:
***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
last question: how can you handle the fact that you are very near to the door before unlock it? is there any property on mqtt about the fact that any of the bonded devices are in bluetooth range? on openhub or hass we can deal with the fact that we are away or at home, but I'm trying also to get a trigger for "i'm in front of the door" as the nuki app does. what do you use in your scenario @bartsnijder ? |
Beta Was this translation helpful? Give feedback.
-
I use a few means to automatically open the lock
|
Beta Was this translation helpful? Give feedback.
-
ok so you have also a nuki hub...
Roberto Viola
Software engineer and open source enthusiast
http://robertoviola.cloud
Il giorno mar 23 gen 2024 alle 13:30 bartsnijder ***@***.***>
ha scritto:
… I use a few means to automatically open the lock
- BLE presence (of NUKI hub): I do limit based on BLE signal strength
- Mobile phone and/or car connected to my LAN on a specific AP
(+signal strength) (this does have some extra delay)
—
Reply to this email directly, view it on GitHub
<#274 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AAALYWF6IHW7ZQTOEB3JFILYP6UPPAVCNFSM6AAAAABCGNCCVGVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTSMBVHE3DCNZZGM>
.
You are receiving this because you authored the thread.Message ID:
***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
No, I edited the reply. By accident I named it a HUB. I only have the
bridge.
Op di 23 jan 2024 om 13:32 schreef Roberto Viola ***@***.***>:
… ok so you have also a nuki hub...
Roberto Viola
Software engineer and open source enthusiast
http://robertoviola.cloud
Il giorno mar 23 gen 2024 alle 13:30 bartsnijder ***@***.***>
ha scritto:
> I use a few means to automatically open the lock
>
> - BLE presence (of NUKI hub): I do limit based on BLE signal strength
> - Mobile phone and/or car connected to my LAN on a specific AP
> (+signal strength) (this does have some extra delay)
>
> —
> Reply to this email directly, view it on GitHub
> <#274 (comment)>,
> or unsubscribe
> <
https://github.com/notifications/unsubscribe-auth/AAALYWF6IHW7ZQTOEB3JFILYP6UPPAVCNFSM6AAAAABCGNCCVGVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTSMBVHE3DCNZZGM>
> .
> You are receiving this because you authored the thread.Message ID:
> ***@***.***>
>
—
Reply to this email directly, view it on GitHub
<#274 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AKCVZ5BDQFUFLXYZJYNQ6E3YP6UXNAVCNFSM6AAAAABCGNCCVGVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTSMBVHE3DIOJVGE>
.
You are receiving this because you were mentioned.Message ID:
***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
The app on the smartphone is not necessarily cloud connected. If you use it without the NUKI Bridge, it directly connects to the lock via bluetooth without communicating with the cloud. |
Beta Was this translation helpful? Give feedback.
-
sorry, just to understand correctly, you mean you only have the ESP32 with the nuki hub? if so, does it expose any data from the bluetooth devices around it?
hah i didn't know this! thanks |
Beta Was this translation helpful? Give feedback.
-
Yes it does, do you have an MQTT browser/viewer (like mqtt explorer). It states all the BLE device found (including signal strength). I think your phone BLE will not be visible by default though; might need an app for that. I use different BLE devices as keys. |
Beta Was this translation helpful? Give feedback.
-
@bartsnijder that's great! i didn't know this! I'm installing https://community.home-assistant.io/t/addon-mqtt-explorer-new-version/603739 (for future reference) to check it and I will report it back. If it's so I guess I'm ready to give it a go! Thanks! |
Beta Was this translation helpful? Give feedback.
-
Correct, you have to install an app that broadcasts ble beacons for your phone to become visible for NUKI Hub. Also, it has to broadcast a name, otherwise the beacon will be ignored. |
Beta Was this translation helpful? Give feedback.
-
that's awesome @technyon thanks! do you know if it also possible on ios? which app do you suggest? |
Beta Was this translation helpful? Give feedback.
-
I'm not using an app myself, but a Siemens G-Tag. I think many people use the Home Assistant companion app, but that only makes sense if you're using home assistant. Just search on the play store ("beacon simulator"), there are a few apps that can do it. I'm not sure about IOS, I'm strictly an android user :). |
Beta Was this translation helpful? Give feedback.
-
In accordance with https://docs.github.com/en/get-started/using-github/communicating-on-github#scenarios-for-github-discussions this open-ended conversation is more suitable for the discussions section imho. @technyon: Now that GitHub discussions is enabled on the repository I propose we convert this issue to a discussion. |
Beta Was this translation helpful? Give feedback.
-
Hi, thanks for this great application!
I just installed and it works flawlessly!
Just a thought: i'm not a fan of closed ecosystem so i would like to DON'T use the nuki app at all for my phone and my wife's phone and use this and the hass integration to do everything.
Does anyone use this in a similar scenario? My idea is that i don't want any IoT device dependent from the cloud or from any 3rd party cloud service
I'm planning to donate to this project in the next weeks if i will keep the nuki device for my house
Thanks!
Beta Was this translation helpful? Give feedback.
All reactions