Skip to content

Latest commit

 

History

History
172 lines (158 loc) · 8.63 KB

Node.md

File metadata and controls

172 lines (158 loc) · 8.63 KB

FDRS Node

A node is a device that sends and receives data from a nearby gateway. This is where the user can communicate with a network of FDRS gateways using their own sketch. A node can be a sensor (sending data), controller (receiving data), or both.

Basic Examples:

Sensor

Sensors load a packet with data, then send the packet to the gateway that they are addressed to.

#include "fdrs_node_config.h"
#include <fdrs_node.h>

void setup() {
  beginFDRS();  // Start the system
  pingFDRS(2000); // Send ping and wait 2000ms for response
}
void loop() {
  loadFDRS(21.0, TEMP_T); // Load a temperature of 21.0 into the queued packet
  sendFDRS();        // Send the queued packet
  sleepFDRS(60); // Sleep for 60 seconds
}

Controller

Controllers register with the gateway they are addressed to, then receive data from it.

#include "fdrs_node_config.h"
#include <fdrs_node.h>

void fdrs_recv_cb(DataReading theData) {
  DBG("ID: " + String(theData.id));
  DBG("Type: " + String(theData.t));
  DBG("Data: " + String(theData.d));
}

void setup() {
  beginFDRS();       // Start the system
  addFDRS(fdrs_recv_cb);  // Call fdrs_recv_cb() when data arrives.
  subscribeFDRS(42);  // Subscribe to DataReadings with ID 42
}
void loop() {
  loopFDRS();  // Listen for data
}

Addresses

#define READING_ID  n

The unique ID that the node will use when sending sensor values. Can be any integer 0 - 65535. Nodes are not necessarily tied to this parameter. They can be subscribed to up to 256 different IDs or send using several different IDs.

#define GTWY_MAC  0xnn

The UNIT_MAC of the gateway that this device will be paired with.

Usage

beginFDRS();

Initializes FDRS, powers up the sensor array, and begins ESP-NOW and/or LoRa.

uint32_t pingFDRS(timeout);

Sends a ping request to the device's paired gateway with a timeout in ms. Returns the ping time in ms and displays it on the debugging console.

Sensor API

loadFDRS(float data, uint8_t type, uint16_t id);

Loads some data into the current packet. 'data' is a float, 'type' is the data type (see below), and 'id' is the DataReading id.

loadFDRS((float data, uint8_t type);

Same as above, but the 'id' is preset to the node's READING_ID.

bool sendFDRS();

Sends the current packet using ESP-NOW and/or LoRa. Returns true if packet is confirmed to have been received successfully by the gateway.

bool sendFDRSAsync();

Queues the current packet to be sent asynchronously (in the background). Be sure to use loopFDRS() to ensure the system can process the packet. Returns true if packet is successfully added to queue.

sleepFDRS(seconds)

Time to sleep in seconds. If DEEP_SLEEP is enabled, the device will enter sleep. Otherwise it will use a simple delay().

Controller API

addFDRS(void callback);

Initializes controller functionality by selecting the function to be called when incoming commands are received. If using LoRa, the controller will automatically receive any packets sent with broadcastLoRa(), provided they were sent by the paired gateway. ESP-NOW requires the device to register with its gateway before it will receive incoming commands. This is done automatically, and the ESP-NOW node will continue recieving data until the paired gateway is reset. A maximum of 16 ESP-NOW controllers can receive data from a single gateway. There is no limit to how many LoRa controllers can listen to the same gateway.

subscribeFDRS(uint16_t sub_id);

Sets the device to listen for a specific DataReading id. When a DataReading with id sub_id is received, the callback function will be called and given the full DataReading as a parameter.

unsubscribeFDRS(uint16_t sub_id);

Removes sub_id from subscription list.

loopFDRS();

Always add this to loop() to handle the controller's listening capabilities.

Configuration

#define USE_ESPNOW

Enables/disables ESP-NOW.

#define USE_LORA

Enables/disables LoRa.

#define FDRS_DEBUG

This definition enables debug messages to be sent over the serial port. If disabled, no serial debug interface will be initialized.

#define DBG_LEVEL n

Sets the level of verbosity in debug messages. '0' (default) shows only the most important system messages, '1' will show additional debug messages for troubleshooting, and '2' will show all messages, including those used in development. Much gratitude to Jeff Lehman for this feature!

#define DEEP_SLEEP

If enabled, device will enter deep-sleep when the sleepFDRS() command is used. If using ESP8266, be sure that you connect the WAKE pin (GPIO 16) to RST or your device will not wake up.

#define POWER_CTRL n

If defined, power control will bring a GPIO pin high when FDRS is initialized. This is useful for powering sensors while running on battery.

LoRa Configuration

#define LORA_ACK

Enables LoRa packet acknowledgement. The device will use CRC to ensure that the data arrived at its destination correctly. If disabled, sendFDRS() will always return true when sending LoRa packets. Thanks Jeff Lehman for this feature!

#define RADIOLIB_MODULE cccc

The name of the RadioLib module being used. Tested modules: SX1276, SX1278, SX1262.

#define LORA_SS n

LoRa chip select pin.

#define LORA_RST n

LoRa reset pin.

#define LORA_DIO n

LoRa DIO pin. This refers to DIO1 on SX127x chips and DIO1 on SX126x chips.

#define LORA_BUSY n

For SX126x chips: LoRa BUSY pin. For SX127x: DIO1 pin, or "RADIOLIB_NC" to leave it blank.

#define LORA_TXPWR n

LoRa TX power in dBm.

#define USE_SX126X

Enable this if using the SX126x series of LoRa chips.

SSD1306 OLED Display

Built on the ThingPulse OLED SSD1306 Library

#define OLED_HEADER "cccc"

The message to be displayed at the top of the screen.

#define OLED_SDA n and OLED_SCL n

OLED I²C pins.

#define OLED_RST n

OLED reset pin. Use '-1' if not present or known.

Callback Function

The callback function is executed when data arrives with an ID that the controller is subscribed to. Inside of this function, the user has access to the incoming DataReading. If multiple readings are received, the function will be called for each of them. While you should always be brief in interrupt callbacks (ISRs), it's okay to do more in this one.

Type Definitions

For the moment, my thought is to reserve the first two bits of the type. I might use them in the future to indicate the data size or type (bool, char,  int, float, etc?). This leaves us with 64 possible type definitions. If you have more types to add, please get in touch!

#define STATUS_T        0  // Status 
#define TEMP_T          1  // Temperature 
#define TEMP2_T         2  // Temperature #2
#define HUMIDITY_T      3  // Relative Humidity 
#define PRESSURE_T      4  // Atmospheric Pressure 
#define LIGHT_T         5  // Light (lux) 
#define SOIL_T          6  // Soil Moisture 
#define SOIL2_T         7  // Soil Moisture #2 
#define SOILR_T         8 // Soil Resistance 
#define SOILR2_T        9 // Soil Resistance #2 
#define OXYGEN_T        10 // Oxygen 
#define CO2_T           11 // Carbon Dioxide
#define WINDSPD_T       12 // Wind Speed
#define WINDHDG_T       13 // Wind Direction
#define RAINFALL_T      14 // Rainfall
#define MOTION_T        15 // Motion
#define VOLTAGE_T       16 // Voltage
#define VOLTAGE2_T      17 // Voltage #2
#define CURRENT_T       18 // Current
#define CURRENT2_T      19 // Current #2
#define IT_T            20 // Iterations
#define LATITUDE_T      21 // GPS Latitude
#define LONGITUDE_T     22 // GPS Longitude
#define ALTITUDE_T      23 // GPS Altitude
#define HDOP_T          24 // GPS HDOP
#define LEVEL_T         25 // Fluid Level
#define UV_T            26 // UV
#define PM1_T           27 // 1 Particles
#define PM2_5_T         28 // 2.5 Particles
#define PM10_T          29 // 10 Particles
#define POWER_T         30 // Power
#define POWER2_T        31 // Power #2
#define ENERGY_T        32 // Energy
#define ENERGY2_T       33 // Energy #2

Under the Hood

typedef struct __attribute__((packed)) DataReading {
  float d;
  uint16_t id;
  uint8_t t;
} DataReading;

Each node in the system sends its data inside of a structure called a DataReading. Its global sensor address is represented by an integer 'id', and each type of reading is represented by a single byte 't'.  If a sensor or gateway needs to send multiple DataReadings, then they are sent in an array. A single DataReading.id may have readings of multiple types ('t') associated with it.