Merge pull request #265 from toblum/develop

v 2.1.6

.gitmodules

@@ -0,0 +1,6 @@
+[submodule "Arduino/McLighting/data/McLightingUI"]
+	path = Arduino/McLighting/data/McLightingUI
+	url = https://github.com/toblum/McLightingUI
+[submodule "clients/web/McLightingUI"]
+	path = clients/web/McLightingUI
+	url = https://github.com/toblum/McLightingUI

Arduino/McLighting/McLighting.ino

@@ -64,32 +64,6 @@ WebSocketsServer webSocket = WebSocketsServer(81);
 ESP8266HTTPUpdateServer httpUpdater;
 #endif
 
-#ifdef USE_NEOANIMATIONFX
-// ***************************************************************************
-// Load libraries / Instanciate NeoAnimationFX library
-// ***************************************************************************
-// https://github.com/debsahu/NeoAnimationFX
-#include <NeoAnimationFX.h>
-#define NEOMETHOD NeoPBBGRB800
-
-NEOMETHOD neoStrip(NUMLEDS);
-NeoAnimationFX<NEOMETHOD> strip(neoStrip);
-
-// Uses Pin RX / GPIO3 (Only pin that is supported, due to hardware limitations)
-// NEOMETHOD NeoPBBGRB800 uses GRB config 800 KHz bitstream (most NeoPixel products w/WS2812 LEDs)
-// NEOMETHOD NeoPBBGRB400 uses GRB config 400 KHz (classic 'v1' (not v2) FLORA pixels, WS2811 drivers)
-// NEOMETHOD NeoPBBRGB800 uses RGB config 800 KHz bitstream (most NeoPixel products w/WS2812 LEDs)
-// NEOMETHOD NeoPBBRGB400 uses RGB config 400 KHz (classic 'v1' (not v2) FLORA pixels, WS2811 drivers)
-
-// Uses Pin D4 / GPIO2 (Only pin that is supported, due to hardware limitations)
-// NEOMETHOD NeoPBBGRBU800 uses GRB config 800 KHz bitstream (most NeoPixel products w/WS2812 LEDs)
-// NEOMETHOD NeoPBBGRBU400 uses GRB config 400 KHz (classic 'v1' (not v2) FLORA pixels, WS2811 drivers)
-// NEOMETHOD NeoPBBRGBU800 uses RGB config 800 KHz bitstream (most NeoPixel products w/WS2812 LEDs)
-// NEOMETHOD NeoPBBRGBU400 uses RGB config 400 KHz (classic 'v1' (not v2) FLORA pixels, WS2811 drivers)
-
-#endif
-
-#ifdef USE_WS2812FX
 // ***************************************************************************
 // Load libraries / Instanciate WS2812FX library
 // ***************************************************************************
@@ -109,6 +83,23 @@ WS2812FX strip = WS2812FX(NUMLEDS, PIN, NEO_GRB + NEO_KHZ800);
 // pixel power leads, add 300 - 500 Ohm resistor on first pixel's data input
 // and minimize distance between Arduino and first pixel.  Avoid connecting
 // on a live circuit...if you must, connect GND first.
+
+#ifdef USE_WS2812FX_DMA
+  #include <NeoPixelBus.h>
+  NeoEsp8266Dma800KbpsMethod dma = NeoEsp8266Dma800KbpsMethod(NUMLEDS, 3);  //800 KHz bitstream (most NeoPixel products w/WS2812 LEDs)
+  //NeoEsp8266Dma400KbpsMethod dma = NeoEsp8266Dma400KbpsMethod(NUMLEDS, 3);  //400 KHz (classic 'v1' (not v2) FLORA pixels, WS2811 drivers)
+#endif
+#ifdef USE_WS2812FX_UART
+  #include <NeoPixelBus.h>
+  NeoEsp8266Uart800KbpsMethod dma = NeoEsp8266Uart800KbpsMethod(NUMLEDS, 3);
+#endif
+#if defined(USE_WS2812FX_DMA) or defined(USE_WS2812FX_UART)
+  void DMA_Show(void) {
+    if(dma.IsReadyToUpdate()) {
+      memcpy(dma.getPixels(), strip.getPixels(), dma.getPixelsSize());
+      dma.Update();
+    }
+  }
 #endif
 
 // ***************************************************************************
@@ -265,6 +256,10 @@ void setup() {
   // Setup: Neopixel
   // ***************************************************************************
   strip.init();
+  #if defined(USE_WS2812FX_DMA) or defined(USE_WS2812FX_UART)
+    dma.Initialize();
+    strip.setCustomShow(DMA_Show);
+  #endif
   strip.setBrightness(brightness);
   strip.setSpeed(convertSpeed(ws2812fx_speed));
   //strip.setMode(FX_MODE_RAINBOW_CYCLE);
@@ -511,12 +506,15 @@ void setup() {
     json["core_version"] = ESP.getCoreVersion();
     json["cpu_freq"] = ESP.getCpuFreqMHz();
     json["chip_id"] = ESP.getFlashChipId();
-    #ifndef USE_NEOANIMATIONFX
-    json["animation_lib"] = "WS2812FX";
-    json["pin"] = PIN;
+    #if defined(USE_WS2812FX_DMA)
+      json["animation_lib"] = "WS2812FX_DMA";
+      json["pin"] = 3;
+    #elif defined(USE_WS2812FX_UART)
+      json["animation_lib"] = "WS2812FX_UART";
+      json["pin"] = 2;
     #else
-    json["animation_lib"] = "NeoAnimationFX";
-    json["pin"] = "Ignored, check NEOMETHOD";
+      json["animation_lib"] = "WS2812FX";
+      json["pin"] = PIN;
     #endif
     json["number_leds"] = NUMLEDS;
     #ifdef ENABLE_BUTTON