-
Notifications
You must be signed in to change notification settings - Fork 462
/
if64
139 lines (116 loc) · 8.48 KB
/
if64
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
title: Monitor network interfaces via standard MIB using 64 Bit counters
agents: snmp
author: Mathias Kettner <mk@mathias-kettner.de>
license: GPL
distribution: check_mk
description:
This check does exactly the same as {if} but uses 64 bit counters from
the {IF-MIB} below {.1.3.6.1.2.1.31.1.1.1}. This allows to correctly
monitor switch ports with a traffic of more then 2GB per check interval.
Also this check can use {ifAlias} instead if {ifDescr} for retrieving
the admin-configured interface description. This is e.g. useful for HP ProCurve
switches which do not show that aliasses in {ifDescr}.
{Note}: This check needs SNMP v2c and thus only works, if you hosts are
added to {bulkwalk_hosts}.
Depending on the check paramters this check can go WARN or CRIT when the
port status changes (i.e. is down), when the link speed changes (e.g. a
port expected to be set to 1GBit/s operates only at 100MBit/s), when the
absolute or procentual traffic of a port exceeds certain levels or if the
rate of errors or discards exceeds configurable limits.
As of Check_MK version 1.1.9i1 this check supports averaging the in- and
outgoing traffic over a configurable range of time by using an exponentially
weighted moving average - just as Linux does for the CPU load averages.
The averaging can be configured on a per host and per port base. This is
done by adding a key {"average"} to the parameter dictionary with the number
of minutes that the average should cover as its key. Port with averaging
turned on output two additional performance values: the averaged traffic
in bytes. If you have configured traffic levels, then those levels are
applied to the averaged values.
item:
There are three allowed ways to specify a port: {1}: the last component of
the SNMP OID number (as string), the {ifDescr} of the port or the {ifAlias} of
the port. If you are using the alias, you have to make sure that it is unique
by configuring useful aliases in the switch. Check_MK does not check for uniqueness.
inventory:
The inventory creates one service for each port that fulfills configurable conditions.
Per default these are ports which are currently found {up} and are of types {6} (ethernetCsmacd),
{32} (frameRelay) or {117} (gigabitEthernet).
perfdata:
{in}: The number of bytes received per second.
{inucast}: The number of unicast packets received per second.
{innucast}: The number of broadcast and multicast packets per second.
{indisc}: The number of discarded received packets per second.
{inerr}: The number of input errors per second.
{out}: The number of bytes sent per second.
{outucast}: The number of unicast packets sent per second.
{outnucast}: The number of broadcast and multicast packets sent per second.
{outdisc}: The number of output packets discarded per second.
{outerr}: The number of output errors per second.
{outqlen}: The current length of the output queue.
{in_avg_?}: optional: The averaged number of received bytes over a longer range of time
{out_avg_?}: optional: The averaged number of sent bytes
[parameters]
parameters (dict): Due to its complexity, this check now uses a dictionary as
parameter. The tuple representation used up to version 1.1.8 are
currently still supported but discouraged. The dictionary can have
the following keys:
{"errors"} - a pair of two float values to be used as WARN/CRIT
percentages for errors + discards. The default is {(0.01, 0.1)} - which
means that the services gets WARN if the error rate is at least
0.01 percent. That means that one error per 10,000 packages is seen.
{"traffic"} - a pair of two float values to be used as WARN/CRIT
levels for the bandwidth usage of the port. Integer numbers are interpreted
as bytes per seconds. So a value of {(500,1000)} will trigger WARN/CRIT
if either the ingoing or outgoing traffic exceeds 500/1000 bytes per second.
If you use floating point number, those are interpreted as percentages
of the available bandwidth as signalled by the port. A value of {(50.0, 80.0)}
will trigger WARN/CRIT, if at least 50%/80% of the nominal bandwidth is
used. The default is to impose no levels on the traffic.
{"average"} - if you set this key to a number, then it is interpreted as
a time in minutes. The check will then compute the averaged used traffic
over approximately that range of time. Note: The algorithm used here is
the same as Linux uses for the CPU load. This means that more recent values
are weighted higher than older values and that even values out of the configured
time range are - to a low degree - represented in the average. If you configure
an average, then the traffic levels are applied to the averaged values.
{"state"} - the expected operational status of the interface (as string or list of strings. If this
is {None} then the state is not checked. Possible values for the
state are {"1"}(up), {"2"}(down), {"3"}(testing), {"4"}(unknown),
{"5"}(dormant), {"6"}(notPresent) and {"7"}(lowerLayerDown). The default is to
remember the state found during inventory and enforce this. It is allowed to
set {"state"} either to a string (one single allowed state) or a list of
strings. For example set this to '{["1", "5"]}' if you want to allow {up}
and {dormant}.
{"speed"} - the expected port speed as an integer of the bits per second (not
the bytes!). If you set this to {None}, then the port speed is not checked.
The default is to remember and enforce the port speed found during inventory.
[configuration]
if_inventory_porttypes (list of strings): List of interface types the inventory should create checks for.
Default is {[ '6', '32', '117' ]}, which means that all Ethernet, Frame Relay and Gigabit Ethernet ports
will be monitored. Virtual and loopback ports will be ignored. Please look into the check implementation
of in the SNMP MIB description of {ifType} for a complete list of port types.
if_inventory_portstates (list of strings): Per default this variable is set to {['1']}, which means that
only ports found in the state {up} are being added to the monitoring. If you set this to {['1', '2', '5']} then
also ports in state {down} and {dormant} will be monitored.
if_inventory_pad_portnumbers (boolean): If this is set to {True} (the default), then port numbers used as
items are padded with zeroes so that all items have the same length and ports will sort correctly in
the GUI. You can set this to {False} if you want to keep the same service descriptions as in versions
prior to 1.1.13i3.
if_inventory_uses_description (boolean): Whether inventory should use the interface description as item (instead
of the interface index). Default is {False}.
if_inventory_uses_alias (boolean): Whether inventory should use the interface alias as item. Please note,
that the {if} check uses parts of the MIB which do not support alias and always use the description as
alias. This option is only interesting if you are using {if64} checks.
if_inventory_monitor_speed (boolean): Whether inventory should code the current speed setting of the port
into the check parameters and thus enforces a static speed setting on this port. Default is {False},
which will code {None} as target speed.
if_inventory_monitor_state (boolean): Whether inventory should code the current port status into the
check parameters and thus enforces the status of the port not to be changed in future. Default is {True} -
so the port states will be monitored. Setting this to {False} will disable status checking of all
newly inventorized ports.
if_default_error_levels (float, float): Default levels for errors. The default is {(0.01, 0.1)}, setting
the levels to 0.01 and 0.1 percent of total packages.
if_default_traffic_levels (float/int, float/int): Default levels for checking traffic (used bandwitdh). The
default is {(None, None)}, which means the the traffic is not being checked - just monitored.
if_default_average (int): Default time range for averaging in minutes. This is preset to {None}, which disables
averaging of port traffic.