Spark-io is a Firmata-compatibility IO class for writing node programs that interact with Spark devices.
In order to use the spark-io library, you will need to load the special voodoospark firmware onto your device. We recommend you review the Getting Started over there before continuing further.
The "Hello World" of microcontroller programming:
var Spark = require("spark-io");
var board = new Spark({
token: "{{yours}}",
deviceId: "{{yours}}"
});
board.on("ready", function(data) {
console.log("CONNECTED", data);
var byte = 0;
setInterval(function() {
console.log("message");
this.digitalWrite("D7", (byte ^= 1));
}.bind(this), 500);
});Spark-IO can be used as an IO Plugin for Johnny-Five:
var five = require("johnny-five");
var Spark = require("spark-io");
var board = new five.Board({
io: new Spark({
token: "{{yours}}",
deviceId: "{{yours}}"
})
});
board.on("ready", function() {
var led = new five.Led("D7");
led.blink();
});This is copied directly from The Tinker API.
digitalWrite(pin, value)
Sets the pin to 1 or 0, which either connects it to 3.3V (the maximum voltage of the system) or to GND (ground). Pin D7 is connected to an on-board LED; if you set pin D7 to HIGH, the LED will turn on, and if you set it to LOW, it will turn off.
The parameters must be the pin (A0 to A7, D0 to D7), followed by either HIGH or LOW, separated by a comma. The return value will be 1 if the write succeeds, and -1 if it fails.
Example:
// This will turn on the on-board LED
board.digitalWrite("D7", 1);analogWrite(pin, value)
Sets the pin to a value between 0 and 255, where 0 is the same as LOW and 255 is the same as HIGH. This is sort of like sending a voltage between 0 and 3.3V, but since this is a digital system, it uses a mechanism called Pulse Width Modulation, or PWM. You could use analogWrite to dim an LED, as an example.
The parameters must be the pin (A0 to A7, D0 to D7), followed by an integer value from 0 to 255, separated by a comma. The return value will be 1 if the write succeeds, and -1 if it fails.
Example:
// Crank an LED to full brightness
board.analogWrite("A7", 255);servoWrite(pin, value) This is an alias to analogWrite
digitalRead(pin, handler) Setup a continuous read handler for specific digital pin.
This will read the digital value of a pin, which can be read as either HIGH or LOW. If you were to connect the pin to 3.3V, it would read HIGH; if you connect it to GND, it would read LOW. Anywhere in between, it’ll probably read whichever one it’s closer to, but it gets dicey in the middle.
The parameters must be the pin (A0 to A7, D0 to D7). The return value will be between 0 and 4095 if the read succeeds, and -1 if it fails.
Example:
// Log all the readings for D1
board.digitalRead("D1", function(data) {
console.log(data);
});analogRead(pin, handler) Setup a continuous read handler for specific analog pin.
This will read the analog value of a pin, which is a value from 0 to 4095, where 0 is LOW (GND) and 4095 is HIGH (3.3V). All of the analog pins (A0 to A7) can handle this. analogRead is great for reading data from sensors.
The parameters must be the pin (A0 to A7, D0 to D7). The return value will be between 0 and 4095 if the read succeeds, and -1 if it fails.
Example:
// Log all the readings for A1
board.analogRead("A1", function(data) {
console.log(data);
});See LICENSE file.