This project contains configuration and scripts to support running Arcus Smart Home in Kubernetes (on-prem, and in the future in the cloud).
You either access to a Kubernetes environment, or suitable bare metal to run one on. You should have 12GB or more of RAM, and at least 20GB of disk space. In order to obtain browser-trusted certificates, you will need to have Arcus publicly accessible, on a well known port (80/443). Using self-signed certificates is not recommended, and will not be supported by the iOS or Android applications (outside of modifying the trust store yourself).
In order to create an account, you will need to have a smarty streets account (for address verification).
For notifications, you must create a Twilio and Sendgrid account. APNS and GCM support is disabled by default and must be configured if desired. Typically this also requires that you distribute and side-load the app onto you device.
Kubernetes is a fast-moving environment. As a result, only the latest version is currently supported. In order to get security updates, you should roll your containers on a frequent basis, depending on your risk tolerance. It is recommended that you do this at least weekly. In the intest of security future releases of Arcus may "expire" such that they will not work if you forget to patch. Further, some third-party dependencies may require a rebuild of the cluster. Ideally, arcuscmd.sh install will try to solve this as much as possible, but it may not be possible in all circumstances.
k3s by rancher is the recommended means of installing Kubernetes, as it's more trimmed down and allows this project to use more modern versions of kubernetes projects, like istio.
Simply execute:
./arcuscmd.sh setup
and choose "local" and then "k3s"
Note: although microk8s works on multiple linux distributions, the script will currently only work on debian based systems, and has only been tested on Ubuntu 18.04.
Simply execute:
./arcuscmd.sh setup
You will be prompted to answer some questions, including the credentials for SmartyStreets (which you will need to use to satisfy the requirement to verify your address). For instructions around setting up networking, see below:
If something fails, wait a few minutes and try again.
It will takes about 5-10 minutes for everything to come up. When microk8s.kubectl get pods shows a list of pods in the running or completed state, you are good to go.
In order to Access the Arcus UI and connect a hub, you will need to configure your network. You have some options when it comes to this. If you are operating in a home environment (e.g. you have NAT and you're behind a gateway), then you have Arcus run a "LoadBalancer" on your local network. For this configuration, you will need to exclude a region of your network from DHCP. For example, if you are using the 192.168.1.1/24 subnet, then you should configure DHCP to assign addresses between 192.168.1.2-192.168.150, and use 192.168.151-192.168.155 for Arcus.
Once you have configured this, and Arcus is running you should check to see which IP addresses in that space are actually being used. You can either do this via kubectl, or with the info utility in arcuscmd.
$ ./arcuscmd.sh info
DNS -> IP/Port Mappings:
If these IP addresses are private, you are responsible for setting up port forwarding
dev.arcus.wl-net.net:80 -> 172.16.6.4:80
dev.arcus.wl-net.net:443 -> 172.16.6.4:443
client.dev.arcus.wl-net.net:443 -> 172.16.6.4:443
static.dev.arcus.wl-net.net:443 -> 172.16.6.4:443
ipcd.dev.arcus.wl-net.net:443 -> 172.16.6.4:443
admin.dev.arcus.wl-net.net:443 -> 172.16.6.4:443
hub.dev.arcus.wl-net.net:443 -> 172.16.6.4:443 OR 172.16.6.2:8082
Alternatively:
$ microk8s.kubectl get service
NAME TYPE CLUSTER-IP EXTERNAL-IP PORT(S) AGE
cassandra-service NodePort 10.152.183.225 <none> 7000:31287/TCP,7001:31914/TCP,7199:32251/TCP,9042:32178/TCP,9160:31262/TCP 27h
client-bridge-service NodePort 10.152.183.68 <none> 80:31803/TCP 27h
hub-bridge-service LoadBalancer 10.152.183.14 172.16.6.1 8082:31804/TCP 6h1m
kafka-service NodePort 10.152.183.250 <none> 9092:30997/TCP 27h
kubernetes ClusterIP 10.152.183.1 <none> 443/TCP 27h
ui-server-service NodePort 10.152.183.88 <none> 80:30787/TCP 27h
zookeeper-service NodePort 10.152.183.132 <none> 2181:30849/TCP 27h
This shows that 172.16.6.1 is the IP address of our hub-bridge service (listening on port 8082).
$ microk8s.kubectl get service -n ingress-nginx
NAME TYPE CLUSTER-IP EXTERNAL-IP PORT(S) AGE
ingress-nginx LoadBalancer 10.152.183.146 172.16.6.0 80:31535/TCP,443:32684/TCP 27h
This shows that 172.16.6.0 is the IP address of the ui-service and client-bridge services (via nginx proxy).
It's beyond the scope of this document to describe how to configure your network, but at a high level you will need to forward traffic to these ports (e.g. port forwarding)
Example (note, you must replace GATEWAY_IP accordingly):
iptables -t nat -A PREROUTING -p tcp -d GATEWAY_IP --dport 8082 -j DNAT --to-destination 172.16.6.1:8082
iptables -t nat -A PREROUTING -p tcp -d GATEWAY_IP --dport 443 -j DNAT --to-destination 172.16.6.0:443
iptables -t nat -A PREROUTING -p tcp -d GATEWAY_IP --dport 8- -j DNAT --to-destination 172.16.6.0:80
iptables -t nat -A POSTROUTING -o eth1 -j MASQUERADE # replace with whatever has the 172.16.6.0 subnet
iptables -P FORWARD ACCEPT
sysctl -w net.ipv4.ip_forward=1
Or configure something similar in your router.
For cloud hosting, this is very similar, but you can use the 127.0.0.1/24 subnet instead, e.g. 172.0.0.5-127.0.10
Once your network is setup, and you are able to access Arcus (and get a certificate warning from the untrusted LetsEncrypt Staging CA), then it's time to setup a production certificate. Currently, this is done by making changes to config/service/ui-service-ingress.yml, although you shouldn't edit this file directly:
Run ./arcuscmd.sh useprodcert
This will apply the configuration - wait a few minutes. You should no longer see a certificate warning when navigating to the site.
You can use microk8s.kubectl -n cert-manager logs $(/snap/bin/microk8s.kubectl get pod -n cert-manager | grep cert-manager- | awk '{print $1}' | grep -v cainject | grep -v webhook) -f to view the logs for cert-manager if you don't get a certificate.
Unfortunately, the hub-bridge doesn't work out of the box because it expects a Java Key Store, something we can't provide with cert-manager. Arcusplatform now supports PKCS#8 keys as well (via netty's internal support for PKCS#8), but the private key that cert-manager generates is in PKCS#1 format. As a result, you'll have to manually convert the private key to PKCS#1.
This can be acomplished by running ./arcuscmd.sh updatehubkeystore once you have production certificates (see above).
kubectl describe pod $POD
where $POD is something like "alarm-service"
The only critical persistent system (at least for the minimum use case) is cassandra. Utility scripts have been provided to assist with backing up and restoring cassandra. Typically you'd want to use snapshots to backup cassandra, however in low-activity use cases like Arcus, you can also just make a tarball of the working directory and restore it.
TIP: you may want to create an alias so that kubectl works, e.g. alias kubectl=microk8s.kubectl. It is recommended that you read through https://kubernetes.io/docs/reference/kubectl/cheatsheet/
kubectl log kafka-0 kafka
kubectl log casandra-0 casandra
The first time you setup Arcus, new secrets will be stored in the secrets directory. Once you have completed ./arcuscmd.sh setup, feel free to adjust any of these secrets to your needs, and further uses of the setup tools in ./arcuscmd.sh will not cause you to loose your secrets.
You can also adjust the configuration in overlays/local-production-local/, however your changes will be lost if you run ./arcuscmd.sh apply.
First update your local copy with git pull or the equivalent arcuscmd command:
./arcuscmd.sh update
Then apply the new configuration:
To install updates for Kubernetes components like cert-manager, do:
./arcuscmd.sh install
NOTE: this make take some time, as pods terminate and restart.
To update arcus configuration, do:
./arcuscmd.sh apply
It is generally recommended to update both at the same time - if you do not update the Kubernetes components for an extended period of time, the may no longer be supported with a newer Arcus configuration.
If you'd like to start over (including wiping any data, or configuration):
microk8s.reset
If you experience difficulties (like microk8s.reset hanging), then you may also need to uninstall microk8s:
snap remove microk8s
You need to have a Google Cloud account, and have configured gcloud and docker on your local system. Instructions on how do this are currently beyond the scope of this project.