Merge tag 'v6.0.10' into 6.0

This is the 6.0.10 stable release

Documentation/driver-api/miscellaneous.rst

@@ -16,12 +16,11 @@ Parallel Port Devices
 16x50 UART Driver
 =================
 
-.. kernel-doc:: drivers/tty/serial/serial_core.c
-   :export:
-
 .. kernel-doc:: drivers/tty/serial/8250/8250_core.c
    :export:
 
+See serial/driver.rst for related APIs.
+
 Pulse-Width Modulation (PWM)
 ============================
 

Documentation/process/code-of-conduct-interpretation.rst

@@ -51,7 +51,7 @@ the Technical Advisory Board (TAB) or other maintainers if you're
 uncertain how to handle situations that come up.  It will not be
 considered a violation report unless you want it to be.  If you are
 uncertain about approaching the TAB or any other maintainers, please
-reach out to our conflict mediator, Joanna Lee <joanna.lee@gesmer.com>.
+reach out to our conflict mediator, Joanna Lee <jlee@linuxfoundation.org>.
 
 In the end, "be kind to each other" is really what the end goal is for
 everybody.  We know everyone is human and we all fail at times, but the

Makefile

@@ -1,7 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0
 VERSION = 6
 PATCHLEVEL = 0
-SUBLEVEL = 9
+SUBLEVEL = 10
 EXTRAVERSION =
 NAME = Hurr durr I'ma ninja sloth
 

arch/arm/boot/dts/imx7s.dtsi

@@ -1270,10 +1270,10 @@
 			clocks = <&clks IMX7D_NAND_USDHC_BUS_RAWNAND_CLK>;
 		};
 
-		gpmi: nand-controller@33002000{
+		gpmi: nand-controller@33002000 {
 			compatible = "fsl,imx7d-gpmi-nand";
 			#address-cells = <1>;
-			#size-cells = <1>;
+			#size-cells = <0>;
 			reg = <0x33002000 0x2000>, <0x33004000 0x4000>;
 			reg-names = "gpmi-nand", "bch";
 			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/boot/dts/sama7g5-pinfunc.h

@@ -261,7 +261,7 @@
 #define PIN_PB2__FLEXCOM6_IO0		PINMUX_PIN(PIN_PB2, 2, 1)
 #define PIN_PB2__ADTRG			PINMUX_PIN(PIN_PB2, 3, 1)
 #define PIN_PB2__A20			PINMUX_PIN(PIN_PB2, 4, 1)
-#define PIN_PB2__FLEXCOM11_IO0		PINMUX_PIN(PIN_PB2, 6, 3)
+#define PIN_PB2__FLEXCOM11_IO1		PINMUX_PIN(PIN_PB2, 6, 3)
 #define PIN_PB3				35
 #define PIN_PB3__GPIO			PINMUX_PIN(PIN_PB3, 0, 0)
 #define PIN_PB3__RF1			PINMUX_PIN(PIN_PB3, 1, 1)

arch/arm/mach-at91/pm_suspend.S

@@ -169,10 +169,15 @@ sr_ena_2:
 	cmp	tmp1, #UDDRC_STAT_SELFREF_TYPE_SW
 	bne	sr_ena_2
 
-	/* Put DDR PHY's DLL in bypass mode for non-backup modes. */
+	/* Disable DX DLLs for non-backup modes. */
 	cmp	r7, #AT91_PM_BACKUP
 	beq	sr_ena_3
 
+	/* Do not soft reset the AC DLL. */
+	ldr	tmp1, [r3, DDR3PHY_ACDLLCR]
+	bic	tmp1, tmp1, DDR3PHY_ACDLLCR_DLLSRST
+	str	tmp1, [r3, DDR3PHY_ACDLLCR]
+
 	/* Disable DX DLLs. */
 	ldr	tmp1, [r3, #DDR3PHY_DX0DLLCR]
 	orr	tmp1, tmp1, #DDR3PHY_DXDLLCR_DLLDIS

arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts

@@ -34,11 +34,25 @@
 		off-on-delay-us = <12000>;
 	};
 
-	extcon_usbotg1: extcon-usbotg1 {
-		compatible = "linux,extcon-usb-gpio";
+	connector {
+		compatible = "gpio-usb-b-connector", "usb-b-connector";
+		type = "micro";
+		label = "X19";
 		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_usb1_extcon>;
-		id-gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&pinctrl_usb1_connector>;
+		id-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				usb_dr_connector: endpoint {
+					remote-endpoint = <&usb1_drd_sw>;
+				};
+			};
+		};
 	};
 };
 
@@ -105,13 +119,19 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usbotg1>;
 	dr_mode = "otg";
-	extcon = <&extcon_usbotg1>;
 	srp-disable;
 	hnp-disable;
 	adp-disable;
 	power-active-high;
 	over-current-active-low;
+	usb-role-switch;
 	status = "okay";
+
+	port {
+		usb1_drd_sw: endpoint {
+			remote-endpoint = <&usb_dr_connector>;
+		};
+	};
 };
 
 &usbotg2 {
@@ -231,7 +251,7 @@
 			   <MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC		0x84>;
 	};
 
-	pinctrl_usb1_extcon: usb1-extcongrp {
+	pinctrl_usb1_connector: usb1-connectorgrp {
 		fsl,pins = <MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10		0x1c0>;
 	};
 

arch/arm64/boot/dts/freescale/imx8mm.dtsi

@@ -1244,10 +1244,10 @@
 			clocks = <&clk IMX8MM_CLK_NAND_USDHC_BUS_RAWNAND_CLK>;
 		};
 
-		gpmi: nand-controller@33002000{
+		gpmi: nand-controller@33002000 {
 			compatible = "fsl,imx8mm-gpmi-nand", "fsl,imx7d-gpmi-nand";
 			#address-cells = <1>;
-			#size-cells = <1>;
+			#size-cells = <0>;
 			reg = <0x33002000 0x2000>, <0x33004000 0x4000>;
 			reg-names = "gpmi-nand", "bch";
 			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;

arch/arm64/boot/dts/freescale/imx8mn.dtsi

@@ -1102,7 +1102,7 @@
 		gpmi: nand-controller@33002000 {
 			compatible = "fsl,imx8mn-gpmi-nand", "fsl,imx7d-gpmi-nand";
 			#address-cells = <1>;
-			#size-cells = <1>;
+			#size-cells = <0>;
 			reg = <0x33002000 0x2000>, <0x33004000 0x4000>;
 			reg-names = "gpmi-nand", "bch";
 			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;

arch/arm64/boot/dts/qcom/ipq8074.dtsi

@@ -668,7 +668,7 @@
 
 		apcs_glb: mailbox@b111000 {
 			compatible = "qcom,ipq8074-apcs-apps-global";
-			reg = <0x0b111000 0x6000>;
+			reg = <0x0b111000 0x1000>;
 
 			#clock-cells = <1>;
 			#mbox-cells = <1>;

arch/arm64/boot/dts/qcom/sa8155p-adp.dts

@@ -43,7 +43,6 @@
 
 		regulator-always-on;
 		regulator-boot-on;
-		regulator-allow-set-load;
 
 		vin-supply = <&vreg_3p3>;
 	};
@@ -137,6 +136,9 @@
 			regulator-max-microvolt = <880000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l7a_1p8: ldo7 {
@@ -152,6 +154,9 @@
 			regulator-max-microvolt = <2960000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l11a_0p8: ldo11 {
@@ -258,6 +263,9 @@
 			regulator-max-microvolt = <1200000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l7c_1p8: ldo7 {
@@ -273,6 +281,9 @@
 			regulator-max-microvolt = <1200000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l10c_3p3: ldo10 {

arch/arm64/boot/dts/qcom/sa8295p-adp.dts

@@ -83,6 +83,9 @@
 			regulator-max-microvolt = <1200000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l4c: ldo4 {
@@ -98,6 +101,9 @@
 			regulator-max-microvolt = <1200000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l7c: ldo7 {
@@ -113,6 +119,9 @@
 			regulator-max-microvolt = <2504000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l17c: ldo17 {
@@ -121,6 +130,9 @@
 			regulator-max-microvolt = <2504000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 	};
 

arch/arm64/boot/dts/qcom/sc7280.dtsi

@@ -2177,7 +2177,8 @@
 
 		lpass_audiocc: clock-controller@3300000 {
 			compatible = "qcom,sc7280-lpassaudiocc";
-			reg = <0 0x03300000 0 0x30000>;
+			reg = <0 0x03300000 0 0x30000>,
+			      <0 0x032a9000 0 0x1000>;
 			clocks = <&rpmhcc RPMH_CXO_CLK>,
 			       <&lpass_aon LPASS_AON_CC_MAIN_RCG_CLK_SRC>;
 			clock-names = "bi_tcxo", "lpass_aon_cc_main_rcg_clk_src";

arch/arm64/boot/dts/qcom/sc8280xp-crd.dts

@@ -124,6 +124,9 @@
 			regulator-max-microvolt = <2504000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l13c: ldo13 {
@@ -146,6 +149,9 @@
 			regulator-max-microvolt = <1200000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l4d: ldo4 {

arch/arm64/boot/dts/qcom/sc8280xp.dtsi

@@ -885,13 +885,13 @@
 
 		ufs_mem_phy: phy@1d87000 {
 			compatible = "qcom,sc8280xp-qmp-ufs-phy";
-			reg = <0 0x01d87000 0 0xe10>;
+			reg = <0 0x01d87000 0 0x1c8>;
 			#address-cells = <2>;
 			#size-cells = <2>;
 			ranges;
 			clock-names = "ref",
 				      "ref_aux";
-			clocks = <&rpmhcc RPMH_CXO_CLK>,
+			clocks = <&gcc GCC_UFS_REF_CLKREF_CLK>,
 				 <&gcc GCC_UFS_PHY_PHY_AUX_CLK>;
 
 			resets = <&ufs_mem_hc 0>;
@@ -953,13 +953,13 @@
 
 		ufs_card_phy: phy@1da7000 {
 			compatible = "qcom,sc8280xp-qmp-ufs-phy";
-			reg = <0 0x01da7000 0 0xe10>;
+			reg = <0 0x01da7000 0 0x1c8>;
 			#address-cells = <2>;
 			#size-cells = <2>;
 			ranges;
 			clock-names = "ref",
 				      "ref_aux";
-			clocks = <&gcc GCC_UFS_1_CARD_CLKREF_CLK>,
+			clocks = <&gcc GCC_UFS_REF_CLKREF_CLK>,
 				 <&gcc GCC_UFS_CARD_PHY_AUX_CLK>;
 
 			resets = <&ufs_card_hc 0>;
@@ -1181,26 +1181,16 @@
 			usb_0_ssphy: usb3-phy@88eb400 {
 				reg = <0 0x088eb400 0 0x100>,
 				      <0 0x088eb600 0 0x3ec>,
-				      <0 0x088ec400 0 0x1f0>,
+				      <0 0x088ec400 0 0x364>,
 				      <0 0x088eba00 0 0x100>,
 				      <0 0x088ebc00 0 0x3ec>,
-				      <0 0x088ec700 0 0x64>;
+				      <0 0x088ec200 0 0x18>;
 				#phy-cells = <0>;
 				#clock-cells = <0>;
 				clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
 				clock-names = "pipe0";
 				clock-output-names = "usb0_phy_pipe_clk_src";
 			};
-
-			usb_0_dpphy: dp-phy@88ed200 {
-				reg = <0 0x088ed200 0 0x200>,
-				      <0 0x088ed400 0 0x200>,
-				      <0 0x088eda00 0 0x200>,
-				      <0 0x088ea600 0 0x200>,
-				      <0 0x088ea800 0 0x200>;
-				#clock-cells = <1>;
-				#phy-cells = <0>;
-			};
 		};
 
 		usb_1_hsphy: phy@8902000 {
@@ -1242,8 +1232,8 @@
 
 			usb_1_ssphy: usb3-phy@8903400 {
 				reg = <0 0x08903400 0 0x100>,
-				      <0 0x08903c00 0 0x3ec>,
-				      <0 0x08904400 0 0x1f0>,
+				      <0 0x08903600 0 0x3ec>,
+				      <0 0x08904400 0 0x364>,
 				      <0 0x08903a00 0 0x100>,
 				      <0 0x08903c00 0 0x3ec>,
 				      <0 0x08904200 0 0x18>;
@@ -1253,16 +1243,6 @@
 				clock-names = "pipe0";
 				clock-output-names = "usb1_phy_pipe_clk_src";
 			};
-
-			usb_1_dpphy: dp-phy@8904200 {
-				reg = <0 0x08904200 0 0x200>,
-				      <0 0x08904400 0 0x200>,
-				      <0 0x08904a00 0 0x200>,
-				      <0 0x08904600 0 0x200>,
-				      <0 0x08904800 0 0x200>;
-				#clock-cells = <1>;
-				#phy-cells = <0>;
-			};
 		};
 
 		system-cache-controller@9200000 {

arch/arm64/boot/dts/qcom/sm8150-sony-xperia-kumano.dtsi

@@ -348,6 +348,9 @@
 			regulator-max-microvolt = <2960000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l7c_3p0: ldo7 {
@@ -367,6 +370,9 @@
 			regulator-max-microvolt = <2960000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l10c_3p3: ldo10 {