pinctrl: qcom: Add intr_target_width field to support increased numbe…

…r of interrupt targets

[ Upstream commit 9757300 ]

SA8775 and newer target have added support for an increased number of
interrupt targets. To implement this change, the intr_target field, which
is used to configure the interrupt target in the interrupt configuration
register is increased from 3 bits to 4 bits.

In accordance to these updates, a new intr_target_width member is
introduced in msm_pingroup structure. This member stores the value of
width of intr_target field in the interrupt configuration register. This
value is used to dynamically calculate and generate mask for setting the
intr_target field. By default, this mask is set to 3 bit wide, to ensure
backward compatibility with the older targets.

Fixes: 4b6b185 ("pinctrl: qcom: add the tlmm driver sa8775p platforms")
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Ninad Naik <quic_ninanaik@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20230809100634.3961-1-quic_ninanaik@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drivers/pinctrl/qcom/pinctrl-msm.c

@@ -1039,6 +1039,7 @@ static int msm_gpio_irq_set_type(struct irq_data *d, unsigned int type)
 	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
 	struct msm_pinctrl *pctrl = gpiochip_get_data(gc);
 	const struct msm_pingroup *g;
+	u32 intr_target_mask = GENMASK(2, 0);
 	unsigned long flags;
 	bool was_enabled;
 	u32 val;
@@ -1075,13 +1076,15 @@ static int msm_gpio_irq_set_type(struct irq_data *d, unsigned int type)
 	 * With intr_target_use_scm interrupts are routed to
 	 * application cpu using scm calls.
 	 */
+	if (g->intr_target_width)
+		intr_target_mask = GENMASK(g->intr_target_width - 1, 0);
+
 	if (pctrl->intr_target_use_scm) {
 		u32 addr = pctrl->phys_base[0] + g->intr_target_reg;
 		int ret;
 
 		qcom_scm_io_readl(addr, &val);
-
-		val &= ~(7 << g->intr_target_bit);
+		val &= ~(intr_target_mask << g->intr_target_bit);
 		val |= g->intr_target_kpss_val << g->intr_target_bit;
 
 		ret = qcom_scm_io_writel(addr, val);
@@ -1091,7 +1094,7 @@ static int msm_gpio_irq_set_type(struct irq_data *d, unsigned int type)
 				d->hwirq);
 	} else {
 		val = msm_readl_intr_target(pctrl, g);
-		val &= ~(7 << g->intr_target_bit);
+		val &= ~(intr_target_mask << g->intr_target_bit);
 		val |= g->intr_target_kpss_val << g->intr_target_bit;
 		msm_writel_intr_target(val, pctrl, g);
 	}

drivers/pinctrl/qcom/pinctrl-msm.h

@@ -51,6 +51,7 @@ struct msm_function {
  * @intr_status_bit:      Offset in @intr_status_reg for reading and acking the interrupt
  *                        status.
  * @intr_target_bit:      Offset in @intr_target_reg for configuring the interrupt routing.
+ * @intr_target_width:    Number of bits used for specifying interrupt routing target.
  * @intr_target_kpss_val: Value in @intr_target_bit for specifying that the interrupt from
  *                        this gpio should get routed to the KPSS processor.
  * @intr_raw_status_bit:  Offset in @intr_cfg_reg for the raw status bit.
@@ -94,6 +95,7 @@ struct msm_pingroup {
 	unsigned intr_ack_high:1;
 
 	unsigned intr_target_bit:5;
+	unsigned intr_target_width:5;
 	unsigned intr_target_kpss_val:5;
 	unsigned intr_raw_status_bit:5;
 	unsigned intr_polarity_bit:5;

drivers/pinctrl/qcom/pinctrl-sa8775p.c

@@ -54,6 +54,7 @@
 		.intr_enable_bit = 0,		\
 		.intr_status_bit = 0,		\
 		.intr_target_bit = 5,		\
+		.intr_target_width = 4,		\
 		.intr_target_kpss_val = 3,	\
 		.intr_raw_status_bit = 4,	\
 		.intr_polarity_bit = 1,		\