Merge tag 'v5.10.88' into 5.10

This is the 5.10.88 stable release

Documentation/networking/device_drivers/ethernet/intel/ixgbe.rst

@@ -440,6 +440,22 @@ NOTE: For 82599-based network connections, if you are enabling jumbo frames in
 a virtual function (VF), jumbo frames must first be enabled in the physical
 function (PF). The VF MTU setting cannot be larger than the PF MTU.
 
+NBASE-T Support
+---------------
+The ixgbe driver supports NBASE-T on some devices. However, the advertisement
+of NBASE-T speeds is suppressed by default, to accommodate broken network
+switches which cannot cope with advertised NBASE-T speeds. Use the ethtool
+command to enable advertising NBASE-T speeds on devices which support it::
+
+  ethtool -s eth? advertise 0x1800000001028
+
+On Linux systems with INTERFACES(5), this can be specified as a pre-up command
+in /etc/network/interfaces so that the interface is always brought up with
+NBASE-T support, e.g.::
+
+  iface eth? inet dhcp
+       pre-up ethtool -s eth? advertise 0x1800000001028 || true
+
 Generic Receive Offload, aka GRO
 --------------------------------
 The driver supports the in-kernel software implementation of GRO. GRO has

Makefile

@@ -1,7 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0
 VERSION = 5
 PATCHLEVEL = 10
-SUBLEVEL = 87
+SUBLEVEL = 88
 EXTRAVERSION =
 NAME = Dare mighty things
 

arch/arm/boot/dts/imx6ull-pinfunc.h

@@ -82,6 +82,6 @@
 #define MX6ULL_PAD_CSI_DATA04__ESAI_TX_FS                         0x01F4 0x0480 0x0000 0x9 0x0
 #define MX6ULL_PAD_CSI_DATA05__ESAI_TX_CLK                        0x01F8 0x0484 0x0000 0x9 0x0
 #define MX6ULL_PAD_CSI_DATA06__ESAI_TX5_RX0                       0x01FC 0x0488 0x0000 0x9 0x0
-#define MX6ULL_PAD_CSI_DATA07__ESAI_T0                            0x0200 0x048C 0x0000 0x9 0x0
+#define MX6ULL_PAD_CSI_DATA07__ESAI_TX0                           0x0200 0x048C 0x0000 0x9 0x0
 
 #endif /* __DTS_IMX6ULL_PINFUNC_H */

arch/arm/boot/dts/socfpga_arria10_socdk_qspi.dts

@@ -12,7 +12,7 @@
 	flash0: n25q00@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q00aa";
+		compatible = "micron,mt25qu02g", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <100000000>;
 

arch/arm/boot/dts/socfpga_arria5_socdk.dts

@@ -119,7 +119,7 @@
 	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q256a";
+		compatible = "micron,n25q256a", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <100000000>;
 

arch/arm/boot/dts/socfpga_cyclone5_socdk.dts

@@ -124,7 +124,7 @@
 	flash0: n25q00@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q00";
+		compatible = "micron,mt25qu02g", "jedec,spi-nor";
 		reg = <0>;	/* chip select */
 		spi-max-frequency = <100000000>;
 

arch/arm/boot/dts/socfpga_cyclone5_sockit.dts

@@ -169,7 +169,7 @@
 	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q00";
+		compatible = "micron,mt25qu02g", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <100000000>;
 

arch/arm/boot/dts/socfpga_cyclone5_socrates.dts

@@ -80,7 +80,7 @@
 	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q256a";
+		compatible = "micron,n25q256a", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <100000000>;
 		m25p,fast-read;

arch/arm/boot/dts/socfpga_cyclone5_sodia.dts

@@ -116,7 +116,7 @@
 	flash0: n25q512a@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q512a";
+		compatible = "micron,n25q512a", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <100000000>;
 

arch/arm/boot/dts/socfpga_cyclone5_vining_fpga.dts

@@ -224,7 +224,7 @@
 	n25q128@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q128";
+		compatible = "micron,n25q128", "jedec,spi-nor";
 		reg = <0>;		/* chip select */
 		spi-max-frequency = <100000000>;
 		m25p,fast-read;
@@ -241,7 +241,7 @@
 	n25q00@1 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q00";
+		compatible = "micron,mt25qu02g", "jedec,spi-nor";
 		reg = <1>;		/* chip select */
 		spi-max-frequency = <100000000>;
 		m25p,fast-read;

arch/arm64/boot/dts/freescale/imx8mm.dtsi

@@ -866,11 +866,12 @@
 				assigned-clocks = <&clk IMX8MM_CLK_ENET_AXI>,
 						  <&clk IMX8MM_CLK_ENET_TIMER>,
 						  <&clk IMX8MM_CLK_ENET_REF>,
-						  <&clk IMX8MM_CLK_ENET_TIMER>;
+						  <&clk IMX8MM_CLK_ENET_PHY_REF>;
 				assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_266M>,
 							 <&clk IMX8MM_SYS_PLL2_100M>,
-							 <&clk IMX8MM_SYS_PLL2_125M>;
-				assigned-clock-rates = <0>, <0>, <125000000>, <100000000>;
+							 <&clk IMX8MM_SYS_PLL2_125M>,
+							 <&clk IMX8MM_SYS_PLL2_50M>;
+				assigned-clock-rates = <0>, <100000000>, <125000000>, <0>;
 				fsl,num-tx-queues = <3>;
 				fsl,num-rx-queues = <3>;
 				status = "disabled";

arch/arm64/boot/dts/freescale/imx8mn.dtsi

@@ -753,11 +753,12 @@
 				assigned-clocks = <&clk IMX8MN_CLK_ENET_AXI>,
 						  <&clk IMX8MN_CLK_ENET_TIMER>,
 						  <&clk IMX8MN_CLK_ENET_REF>,
-						  <&clk IMX8MN_CLK_ENET_TIMER>;
+						  <&clk IMX8MN_CLK_ENET_PHY_REF>;
 				assigned-clock-parents = <&clk IMX8MN_SYS_PLL1_266M>,
 							 <&clk IMX8MN_SYS_PLL2_100M>,
-							 <&clk IMX8MN_SYS_PLL2_125M>;
-				assigned-clock-rates = <0>, <0>, <125000000>, <100000000>;
+							 <&clk IMX8MN_SYS_PLL2_125M>,
+							 <&clk IMX8MN_SYS_PLL2_50M>;
+				assigned-clock-rates = <0>, <100000000>, <125000000>, <0>;
 				fsl,num-tx-queues = <3>;
 				fsl,num-rx-queues = <3>;
 				status = "disabled";

arch/arm64/boot/dts/freescale/imx8mp-evk.dts

@@ -62,6 +62,8 @@
 			reg = <1>;
 			eee-broken-1000t;
 			reset-gpios = <&gpio4 2 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <80000>;
 		};
 	};
 };

arch/arm64/boot/dts/freescale/imx8mp.dtsi

@@ -725,11 +725,12 @@
 				assigned-clocks = <&clk IMX8MP_CLK_ENET_AXI>,
 						  <&clk IMX8MP_CLK_ENET_TIMER>,
 						  <&clk IMX8MP_CLK_ENET_REF>,
-						  <&clk IMX8MP_CLK_ENET_TIMER>;
+						  <&clk IMX8MP_CLK_ENET_PHY_REF>;
 				assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_266M>,
 							 <&clk IMX8MP_SYS_PLL2_100M>,
-							 <&clk IMX8MP_SYS_PLL2_125M>;
-				assigned-clock-rates = <0>, <0>, <125000000>, <100000000>;
+							 <&clk IMX8MP_SYS_PLL2_125M>,
+							 <&clk IMX8MP_SYS_PLL2_50M>;
+				assigned-clock-rates = <0>, <100000000>, <125000000>, <0>;
 				fsl,num-tx-queues = <3>;
 				fsl,num-rx-queues = <3>;
 				status = "disabled";

arch/arm64/boot/dts/rockchip/rk3308-roc-cc.dts

@@ -91,7 +91,7 @@
 		regulator-max-microvolt = <3300000>;
 		regulator-always-on;
 		regulator-boot-on;
-		vim-supply = <&vcc_io>;
+		vin-supply = <&vcc_io>;
 	};
 
 	vdd_core: vdd-core {

arch/arm64/boot/dts/rockchip/rk3399-khadas-edge.dtsi

@@ -699,7 +699,6 @@
 &sdhci {
 	bus-width = <8>;
 	mmc-hs400-1_8v;
-	mmc-hs400-enhanced-strobe;
 	non-removable;
 	status = "okay";
 };

arch/arm64/boot/dts/rockchip/rk3399-leez-p710.dts

@@ -49,7 +49,7 @@
 		regulator-boot-on;
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
-		vim-supply = <&vcc3v3_sys>;
+		vin-supply = <&vcc3v3_sys>;
 	};
 
 	vcc3v3_sys: vcc3v3-sys {

arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4.dtsi

@@ -459,7 +459,7 @@
 	status = "okay";
 
 	bt656-supply = <&vcc_3v0>;
-	audio-supply = <&vcc_3v0>;
+	audio-supply = <&vcc1v8_codec>;
 	sdmmc-supply = <&vcc_sdio>;
 	gpio1830-supply = <&vcc_3v0>;
 };

arch/powerpc/platforms/85xx/smp.c

@@ -220,7 +220,7 @@ static int smp_85xx_start_cpu(int cpu)
 	local_irq_save(flags);
 	hard_irq_disable();
 
-	if (qoriq_pm_ops)
+	if (qoriq_pm_ops && qoriq_pm_ops->cpu_up_prepare)
 		qoriq_pm_ops->cpu_up_prepare(cpu);
 
 	/* if cpu is not spinning, reset it */
@@ -292,7 +292,7 @@ static int smp_85xx_kick_cpu(int nr)
 		booting_thread_hwid = cpu_thread_in_core(nr);
 		primary = cpu_first_thread_sibling(nr);
 
-		if (qoriq_pm_ops)
+		if (qoriq_pm_ops && qoriq_pm_ops->cpu_up_prepare)
 			qoriq_pm_ops->cpu_up_prepare(nr);
 
 		/*

arch/s390/kernel/machine_kexec_file.c

@@ -277,6 +277,7 @@ int arch_kexec_apply_relocations_add(struct purgatory_info *pi,
 {
 	Elf_Rela *relas;
 	int i, r_type;
+	int ret;
 
 	relas = (void *)pi->ehdr + relsec->sh_offset;
 
@@ -311,7 +312,11 @@ int arch_kexec_apply_relocations_add(struct purgatory_info *pi,
 		addr = section->sh_addr + relas[i].r_offset;
 
 		r_type = ELF64_R_TYPE(relas[i].r_info);
-		arch_kexec_do_relocs(r_type, loc, val, addr);
+		ret = arch_kexec_do_relocs(r_type, loc, val, addr);
+		if (ret) {
+			pr_err("Unknown rela relocation: %d\n", r_type);
+			return -ENOEXEC;
+		}
 	}
 	return 0;
 }

arch/x86/kvm/x86.c

@@ -3065,7 +3065,7 @@ int kvm_set_msr_common(struct kvm_vcpu *vcpu, struct msr_data *msr_info)
 
 		if (!msr_info->host_initiated)
 			return 1;
-		if (guest_cpuid_has(vcpu, X86_FEATURE_PDCM) && kvm_get_msr_feature(&msr_ent))
+		if (kvm_get_msr_feature(&msr_ent))
 			return 1;
 		if (data & ~msr_ent.data)
 			return 1;

block/blk-iocost.c

@@ -2246,7 +2246,14 @@ static void ioc_timer_fn(struct timer_list *timer)
 			hwm = current_hweight_max(iocg);
 			new_hwi = hweight_after_donation(iocg, old_hwi, hwm,
 							 usage, &now);
-			if (new_hwi < hwm) {
+			/*
+			 * Donation calculation assumes hweight_after_donation
+			 * to be positive, a condition that a donor w/ hwa < 2
+			 * can't meet. Don't bother with donation if hwa is
+			 * below 2. It's not gonna make a meaningful difference
+			 * anyway.
+			 */
+			if (new_hwi < hwm && hwa >= 2) {
 				iocg->hweight_donating = hwa;
 				iocg->hweight_after_donation = new_hwi;
 				list_add(&iocg->surplus_list, &surpluses);

drivers/ata/libata-scsi.c

@@ -2870,8 +2870,19 @@ static unsigned int ata_scsi_pass_thru(struct ata_queued_cmd *qc)
 		goto invalid_fld;
 	}
 
-	if (ata_is_ncq(tf->protocol) && (cdb[2 + cdb_offset] & 0x3) == 0)
-		tf->protocol = ATA_PROT_NCQ_NODATA;
+	if ((cdb[2 + cdb_offset] & 0x3) == 0) {
+		/*
+		 * When T_LENGTH is zero (No data is transferred), dir should
+		 * be DMA_NONE.
+		 */
+		if (scmd->sc_data_direction != DMA_NONE) {
+			fp = 2 + cdb_offset;
+			goto invalid_fld;
+		}
+
+		if (ata_is_ncq(tf->protocol))
+			tf->protocol = ATA_PROT_NCQ_NODATA;
+	}
 
 	/* enable LBA */
 	tf->flags |= ATA_TFLAG_LBA;

drivers/block/xen-blkfront.c

@@ -1573,9 +1573,12 @@ static irqreturn_t blkif_interrupt(int irq, void *dev_id)
 	unsigned long flags;
 	struct blkfront_ring_info *rinfo = (struct blkfront_ring_info *)dev_id;
 	struct blkfront_info *info = rinfo->dev_info;
+	unsigned int eoiflag = XEN_EOI_FLAG_SPURIOUS;
 
-	if (unlikely(info->connected != BLKIF_STATE_CONNECTED))
+	if (unlikely(info->connected != BLKIF_STATE_CONNECTED)) {
+		xen_irq_lateeoi(irq, XEN_EOI_FLAG_SPURIOUS);
 		return IRQ_HANDLED;
+	}
 
 	spin_lock_irqsave(&rinfo->ring_lock, flags);
  again:
@@ -1591,6 +1594,8 @@ static irqreturn_t blkif_interrupt(int irq, void *dev_id)
 		unsigned long id;
 		unsigned int op;
 
+		eoiflag = 0;
+
 		RING_COPY_RESPONSE(&rinfo->ring, i, &bret);
 		id = bret.id;
 
@@ -1707,13 +1712,17 @@ static irqreturn_t blkif_interrupt(int irq, void *dev_id)
 
 	spin_unlock_irqrestore(&rinfo->ring_lock, flags);
 
+	xen_irq_lateeoi(irq, eoiflag);
+
 	return IRQ_HANDLED;
 
  err:
 	info->connected = BLKIF_STATE_ERROR;
 
 	spin_unlock_irqrestore(&rinfo->ring_lock, flags);
 
+	/* No EOI in order to avoid further interrupts. */
+
 	pr_alert("%s disabled for further use\n", info->gd->disk_name);
 	return IRQ_HANDLED;
 }
@@ -1753,8 +1762,8 @@ static int setup_blkring(struct xenbus_device *dev,
 	if (err)
 		goto fail;
 
-	err = bind_evtchn_to_irqhandler(rinfo->evtchn, blkif_interrupt, 0,
-					"blkif", rinfo);
+	err = bind_evtchn_to_irqhandler_lateeoi(rinfo->evtchn, blkif_interrupt,
+						0, "blkif", rinfo);
 	if (err <= 0) {
 		xenbus_dev_fatal(dev, err,
 				 "bind_evtchn_to_irqhandler failed");

drivers/bus/ti-sysc.c

@@ -2443,12 +2443,11 @@ static void sysc_reinit_modules(struct sysc_soc_info *soc)
 	struct sysc_module *module;
 	struct list_head *pos;
 	struct sysc *ddata;
-	int error = 0;
 
 	list_for_each(pos, &sysc_soc->restored_modules) {
 		module = list_entry(pos, struct sysc_module, node);
 		ddata = module->ddata;
-		error = sysc_reinit_module(ddata, ddata->enabled);
+		sysc_reinit_module(ddata, ddata->enabled);
 	}
 }
 

drivers/clk/clk.c

@@ -3389,6 +3389,14 @@ static int __clk_core_init(struct clk_core *core)
 
 	clk_prepare_lock();
 
+	/*
+	 * Set hw->core after grabbing the prepare_lock to synchronize with
+	 * callers of clk_core_fill_parent_index() where we treat hw->core
+	 * being NULL as the clk not being registered yet. This is crucial so
+	 * that clks aren't parented until their parent is fully registered.
+	 */
+	core->hw->core = core;
+
 	ret = clk_pm_runtime_get(core);
 	if (ret)
 		goto unlock;
@@ -3557,8 +3565,10 @@ static int __clk_core_init(struct clk_core *core)
 out:
 	clk_pm_runtime_put(core);
 unlock:
-	if (ret)
+	if (ret) {
 		hlist_del_init(&core->child_node);
+		core->hw->core = NULL;
+	}
 
 	clk_prepare_unlock();
 
@@ -3804,7 +3814,6 @@ __clk_register(struct device *dev, struct device_node *np, struct clk_hw *hw)
 	core->num_parents = init->num_parents;
 	core->min_rate = 0;
 	core->max_rate = ULONG_MAX;
-	hw->core = core;
 
 	ret = clk_core_populate_parent_map(core, init);
 	if (ret)
@@ -3822,7 +3831,7 @@ __clk_register(struct device *dev, struct device_node *np, struct clk_hw *hw)
 		goto fail_create_clk;
 	}
 
-	clk_core_link_consumer(hw->core, hw->clk);
+	clk_core_link_consumer(core, hw->clk);
 
 	ret = __clk_core_init(core);
 	if (!ret)