Skip to content

Commit

Permalink
arm64: dts: rockchip: rk3328: Add Radxa ROCK Pi E
Browse files Browse the repository at this point in the history 
Radxa ROCK Pi E is a router oriented SBC based on Rockchip's RK3328 SoC.
As the official wiki page puts it, "E for Ethernets".

It features the RK3328 SoC, gigabit and fast Ethernet RJ45 ports, both
directly served by Ethernet controllers in the SoC, a USB 3.0 host port,
a power-only USB type-C port, a 3.5mm headphone jack for audio output,
two LEDs, a 40-pin Raspberry Pi style GPIO header, and optional WiFi+BT
and PoE header.

The board comes in multiple configurations, differing in the amount of
onboard RAM, the level of WiFi+BT (none, 802.11n 2.4GHz, or 802.11ac
2.4 GHz & 5 GHz), and whether PoE is supported or not. These variants
can all share the same device tree.

The USB 2.0 OTG controller is available on the 40-pin header. This is
not enabled in the device tree, since it is possible to use it in a
host-only configuration, or in OTG mode with an extra pin from the
header as the ID pin.

The device tree is based on the one of the Rock64, with various parts
modified to match the ROCK Pi E, and some parts updated to newer styles,
such as the gmac2io node's mdio sub-node.

Add a new device tree file for the new board.

The voltages for the adc-keys were selected to have some tolerances for
resistor variances and the ADC itself also causing voltage drops. Since
the recover button is the only button on the adc line, this should not
cause any issues.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20210117100710.4857-4-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
  • Loading branch information
@wens @mmind
wens authored and mmind committed Jan 18, 2021
1 parent 31b8e85 commit b918e81
Show file tree
Hide file tree
Showing 2 changed files with 383 additions and 0 deletions.
1 change: 1 addition & 0 deletions arch/arm64/boot/dts/rockchip/Makefile
View file
Original file line number Diff line number Diff line change
Expand Up @@ -11,6 +11,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-nanopi-r2s.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock-pi-e.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-roc-cc.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-evb-act8846.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-geekbox.dtb
Expand Down
382 changes: 382 additions & 0 deletions arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts
View file
Original file line number Diff line number Diff line change
@@ -0,0 +1,382 @@
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* (C) Copyright 2020 Chen-Yu Tsai <wens@csie.org>
*
* Based on ./rk3328-rock64.dts, which is
*
* Copyright (c) 2017 PINE64
*/

/dts-v1/;

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/pinctrl/rockchip.h>

#include "rk3328.dtsi"

/ {
model = "Radxa ROCK Pi E";
compatible = "radxa,rockpi-e", "rockchip,rk3328";

chosen {
stdout-path = "serial2:1500000n8";
};

adc-keys {
compatible = "adc-keys";
io-channels = <&saradc 0>;
io-channel-names = "buttons";
keyup-threshold-microvolt = <1750000>;

/* This button is unpopulated out of the factory. */
button-recovery {
label = "Recovery";
linux,code = <KEY_VENDOR>;
press-threshold-microvolt = <10000>;
};
};

gmac_clkin: external-gmac-clock {
compatible = "fixed-clock";
clock-frequency = <125000000>;
clock-output-names = "gmac_clkin";
#clock-cells = <0>;
};

leds {
compatible = "gpio-leds";
pinctrl-0 = <&led_pin>;
pinctrl-names = "default";

led-0 {
color = <LED_COLOR_ID_BLUE>;
gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_LOW>;
linux,default-trigger = "heartbeat";
};
};

vcc_sd: sdmmc-regulator {
compatible = "regulator-fixed";
gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&sdmmc0m1_pin>;
regulator-name = "vcc_sd";
regulator-boot-on;
vin-supply = <&vcc_io>;
};

vcc_host_5v: vcc-host-5v-regulator {
compatible = "regulator-fixed";
gpio = <&gpio3 RK_PA7 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&usb30_host_drv>;
enable-active-high;
regulator-name = "vcc_host_5v";
regulator-always-on;
regulator-boot-on;
vin-supply = <&vcc_sys>;
};

vcc_sys: vcc-sys {
compatible = "regulator-fixed";
regulator-name = "vcc_sys";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
};

vcc_wifi: vcc-wifi-regulator {
compatible = "regulator-fixed";
gpio = <&gpio0 RK_PA0 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&wifi_en>;
regulator-name = "vcc_wifi";
regulator-always-on;
regulator-boot-on;
vin-supply = <&vcc_io>;
};
};

&analog_sound {
status = "okay";
};

&codec {
status = "okay";
};

&cpu0 {
cpu-supply = <&vdd_arm>;
};

&cpu1 {
cpu-supply = <&vdd_arm>;
};

&cpu2 {
cpu-supply = <&vdd_arm>;
};

&cpu3 {
cpu-supply = <&vdd_arm>;
};

&emmc {
bus-width = <8>;
cap-mmc-highspeed;
mmc-ddr-1_8v;
mmc-hs200-1_8v;
non-removable;
pinctrl-names = "default";
pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_bus8>;
vmmc-supply = <&vcc_io>;
vqmmc-supply = <&vcc18_emmc>;
status = "okay";
};

&gmac2io {
assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>;
assigned-clock-parents = <&gmac_clkin>, <&gmac_clkin>;
clock_in_out = "input";
phy-handle = <&rtl8211e>;
phy-mode = "rgmii";
phy-supply = <&vcc_io>;
pinctrl-names = "default";
pinctrl-0 = <&rgmiim1_pins>;
snps,aal;
snps,rxpbl = <0x4>;
snps,txpbl = <0x4>;
tx_delay = <0x26>;
rx_delay = <0x11>;
status = "okay";

mdio {
compatible = "snps,dwmac-mdio";
#address-cells = <1>;
#size-cells = <0>;

rtl8211e: ethernet-phy@1 {
reg = <1>;
pinctrl-0 = <&eth_phy_int_pin>, <&eth_phy_reset_pin>;
pinctrl-names = "default";
interrupt-parent = <&gpio1>;
interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
reset-assert-us = <10000>;
reset-deassert-us = <50000>;
reset-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
};
};
};

&gmac2phy {
pinctrl-names = "default";
pinctrl-0 = <&fephyled_linkm1>, <&fephyled_rxm1>;
status = "okay";
};

&i2c1 {
status = "okay";

rk805: pmic@18 {
compatible = "rockchip,rk805";
reg = <0x18>;
interrupt-parent = <&gpio2>;
interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
#clock-cells = <1>;
clock-output-names = "xin32k", "rk805-clkout2";
gpio-controller;
#gpio-cells = <2>;
pinctrl-names = "default";
pinctrl-0 = <&pmic_int_l>;
rockchip,system-power-controller;
wakeup-source;

vcc1-supply = <&vcc_sys>;
vcc2-supply = <&vcc_sys>;
vcc3-supply = <&vcc_sys>;
vcc4-supply = <&vcc_sys>;
vcc5-supply = <&vcc_io>;
vcc6-supply = <&vcc_sys>;

regulators {
vdd_log: DCDC_REG1 {
regulator-name = "vdd_log";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <712500>;
regulator-max-microvolt = <1450000>;
regulator-ramp-delay = <12500>;

regulator-state-mem {
regulator-on-in-suspend;
regulator-suspend-microvolt = <1000000>;
};
};

vdd_arm: DCDC_REG2 {
regulator-name = "vdd_arm";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <712500>;
regulator-max-microvolt = <1450000>;
regulator-ramp-delay = <12500>;

regulator-state-mem {
regulator-on-in-suspend;
regulator-suspend-microvolt = <950000>;
};
};

vcc_ddr: DCDC_REG3 {
regulator-name = "vcc_ddr";
regulator-always-on;
regulator-boot-on;

regulator-state-mem {
regulator-on-in-suspend;
};
};

vcc_io: DCDC_REG4 {
regulator-name = "vcc_io";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;

regulator-state-mem {
regulator-on-in-suspend;
regulator-suspend-microvolt = <3300000>;
};
};

vcc_18: LDO_REG1 {
regulator-name = "vcc_18";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;

regulator-state-mem {
regulator-on-in-suspend;
regulator-suspend-microvolt = <1800000>;
};
};

vcc18_emmc: LDO_REG2 {
regulator-name = "vcc18_emmc";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;

regulator-state-mem {
regulator-on-in-suspend;
regulator-suspend-microvolt = <1800000>;
};
};

vdd_10: LDO_REG3 {
regulator-name = "vdd_10";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;

regulator-state-mem {
regulator-on-in-suspend;
regulator-suspend-microvolt = <1000000>;
};
};
};
};
};

&i2s1 {
status = "okay";
};

&io_domains {
pmuio-supply = <&vcc_io>;
vccio1-supply = <&vcc_io>;
vccio2-supply = <&vcc18_emmc>;
vccio3-supply = <&vcc_io>;
vccio4-supply = <&vcc_io>;
vccio5-supply = <&vcc_io>;
vccio6-supply = <&vcc_io>;
status = "okay";
};

&pinctrl {
ephy {
eth_phy_int_pin: eth-phy-int-pin {
rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_down>;
};

eth_phy_reset_pin: eth-phy-reset-pin {
rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>;
};
};

leds {
led_pin: led-pin {
rockchip,pins = <3 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
};
};

pmic {
pmic_int_l: pmic-int-l {
rockchip,pins = <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>;
};
};

usb3 {
usb30_host_drv: usb30-host-drv {
rockchip,pins = <3 RK_PA7 RK_FUNC_GPIO &pcfg_pull_none>;
};
};

wifi {
wifi_en: wifi-en {
rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
};

&sdmmc {
bus-width = <4>;
cap-sd-highspeed;
disable-wp;
pinctrl-names = "default";
pinctrl-0 = <&sdmmc0_clk>, <&sdmmc0_cmd>, <&sdmmc0_dectn>, <&sdmmc0_bus4>;
vmmc-supply = <&vcc_sd>;
status = "okay";
};

&saradc {
vref-supply = <&vcc_18>;
status = "okay";
};

&tsadc {
status = "okay";
};

&u2phy {
status = "okay";
};

&u2phy_host {
status = "okay";
};

&uart2 {
status = "okay";
};

&usb_host0_ehci {
status = "okay";
};

0 comments on commit b918e81

Please sign in to comment.