serial: dts: remove !HAS_DTS related Kconfig

As we now only support DTS for ARM based SoCs we can remove any
associated !HAS_DTS bits in Kconfig.  The Nordic NRF5 serial driver and
the ARM CMSDK APB serial drivers had Kconfig bits related to !HAS_DTS
builds.

Signed-off-by: Kumar Gala <kumar.gala@linaro.org>

drivers/serial/Kconfig.cmsdk_apb

@@ -32,25 +32,6 @@ config UART_CMSDK_APB_PORT0_NAME
 	  This is the device name for UART, and is included in the device
 	  struct.
 
-if !HAS_DTS
-
-config UART_CMSDK_APB_PORT0_IRQ_PRI
-	int "UART Interrupt Priority (Interrupt support)"
-	default 2
-	depends on UART_CMSDK_APB_PORT0
-	depends on UART_INTERRUPT_DRIVEN
-	help
-	  The interrupt priority for UART port.
-
-config UART_CMSDK_APB_PORT0_BAUD_RATE
-	int "Baud Rate"
-	range 9600 115200
-	default 115200
-	depends on UART_CMSDK_APB_PORT0
-	help
-	  The baud rate for UART port to be set to at boot.
-
-endif # !HAS_DTS
 # ---------- Port 1 ----------
 
 config UART_CMSDK_APB_PORT1
@@ -67,25 +48,6 @@ config UART_CMSDK_APB_PORT1_NAME
 	  This is the device name for UART, and is included in the device
 	  struct.
 
-if !HAS_DTS
-
-config UART_CMSDK_APB_PORT1_IRQ_PRI
-	int "UART Interrupt Priority (Interrupt support)"
-	default 2
-	depends on UART_CMSDK_APB_PORT1
-	depends on UART_INTERRUPT_DRIVEN
-	help
-	  The interrupt priority for UART port.
-
-config UART_CMSDK_APB_PORT1_BAUD_RATE
-	int "Baud Rate"
-	range 9600 115200
-	default 115200
-	depends on UART_CMSDK_APB_PORT1
-	help
-	  The baud rate for UART port to be set to at boot.
-
-endif # !HAS_DTS
 # ---------- Port 2 ----------
 
 config UART_CMSDK_APB_PORT2
@@ -102,25 +64,6 @@ config UART_CMSDK_APB_PORT2_NAME
 	  This is the device name for UART, and is included in the device
 	  struct.
 
-if !HAS_DTS
-
-config UART_CMSDK_APB_PORT2_IRQ_PRI
-	int "UART Interrupt Priority (Interrupt support)"
-	default 2
-	depends on UART_CMSDK_APB_PORT2
-	depends on UART_INTERRUPT_DRIVEN
-	help
-	  The interrupt priority for UART port.
-
-config UART_CMSDK_APB_PORT2_BAUD_RATE
-	int "Baud Rate"
-	range 9600 115200
-	default 115200
-	depends on UART_CMSDK_APB_PORT2
-	help
-	  The baud rate for UART port to be set to at boot.
-
-endif # !HAS_DTS
 # ---------- Port 3 ----------
 
 config UART_CMSDK_APB_PORT3
@@ -137,25 +80,6 @@ config UART_CMSDK_APB_PORT3_NAME
 	  This is the device name for UART, and is included in the device
 	  struct.
 
-if !HAS_DTS
-
-config UART_CMSDK_APB_PORT3_IRQ_PRI
-	int "UART Interrupt Priority (Interrupt support)"
-	default 2
-	depends on UART_CMSDK_APB_PORT3
-	depends on UART_INTERRUPT_DRIVEN
-	help
-	  The interrupt priority for UART port.
-
-config UART_CMSDK_APB_PORT3_BAUD_RATE
-	int "Baud Rate"
-	range 9600 115200
-	default 115200
-	depends on UART_CMSDK_APB_PORT3
-	help
-	  The baud rate for UART port to be set to at boot.
-
-endif # !HAS_DTS
 # ---------- Port 4 ----------
 
 config UART_CMSDK_APB_PORT4
@@ -172,23 +96,4 @@ config UART_CMSDK_APB_PORT4_NAME
 	  This is the device name for UART, and is included in the device
 	  struct.
 
-if !HAS_DTS
-
-config UART_CMSDK_APB_PORT4_IRQ_PRI
-	int "UART Interrupt Priority (Interrupt support)"
-	default 2
-	depends on UART_CMSDK_APB_PORT4
-	depends on UART_INTERRUPT_DRIVEN
-	help
-	  The interrupt priority for UART port.
-
-config UART_CMSDK_APB_PORT4_BAUD_RATE
-	int "Baud Rate"
-	range 9600 115200
-	default 115200
-	depends on UART_CMSDK_APB_PORT4
-	help
-	  The baud rate for UART port to be set to at boot.
-
-endif # !HAS_DTS
 endif # UART_CMSDK_APB

drivers/serial/Kconfig.nrf5

@@ -24,26 +24,6 @@ config UART_NRF5_NAME
 	  This is the device name for UART, and is included in the device
 	  struct.
 
-if !HAS_DTS
-config UART_NRF5_IRQ_PRI
-	int "UART Interrupt Priority (Interrupt support)"
-	range 0 1 if SOC_SERIES_NRF51X
-	range 0 5 if SOC_SERIES_NRF52X
-	default 1
-	depends on UART_NRF5
-	depends on UART_INTERRUPT_DRIVEN
-	help
-	  The interrupt priority for UART port.
-
-config UART_NRF5_BAUD_RATE
-	int "Baud Rate"
-	range 1200 1000000
-	default 115200
-	depends on UART_NRF5
-	help
-	  The baud rate for UART port to be set to at boot.
-endif
-
 config UART_NRF5_CLK_FREQ
 	int
 	default 16000000