-
Notifications
You must be signed in to change notification settings - Fork 1
Experiência 2
Disclaimer: Esta configuração é para a bancada 2
- Configure tuxy2 and register its IP and MAC addresses
- Create vlany0 in the switch and add corresponding ports
- Create vlany1 and add corresponding port
- Start capture at tuxy3.eth0
- In tuxy3, ping tuxy4 and then ping tuxy2
- Stop capture and save log
- Start new captures in tuxy3.eth0, tuxy4.eth0, and tuxy2.eth0
- In tuxy3, do ping broadcast (ping –b 172.16.y0.255) for a few seconds
- Observe results, stop captures and save logs
- Repeat steps 7, 8 and 9, but now do ping broadcast in tuxy2 (
ping –b 172.16.y1.255
)
Ligar Cabos
TUX23E0 -> Switch Porta 1 (Verificar que luz acende no Switch para saber porta)
TUX24E0 -> Switch Porta 2
TUX22E0 -> Switch Porta 3
Vista frontal das ligações no switch, lado esquerdo | --- | --- | --- | |--------|-------|----| | TUX23E0 (1) | TUX22E0 (3) | empty (5) | | TUX24E0 (2) | empty (4)| empty (6) |
tux23:
> ifconfig eth0 up
> ifconfig eth0 172.16.20.1/24
> ifconfig eth0
tux24:
> ifconfig eth0 up
> ifconfig eth0 172.16.20.254/24
> ifconfig eth0
tux22:
> ifconfig eth0 up
> ifconfig eth0 172.16.21.1/24
> ifconfig eth0
IP | MAC | tux/ether |
---|---|---|
172.16.21.1 | 00:21:5a:61:2b:72 | tux22 eth0 |
172.16.20.1 | 00:21:5a:5a:7d:12 | tux23 eth0 |
172.16.20.254 | 00:08:54:50:3f:2c | tux24 eth0 |
Ligar Cabo
TUX23S0 -> T3
T4 -> Switch Console
--- | --- | --- |
---|---|---|
TUX23E0 (1) | TUX22E0 (3) | empty (5) |
TUX24E0 (2) | empty (4) | empty (6) |
Para criar as vlans vais modificar o switch, para isso escolhes um tux e ligas a porta série desse tux á porta série da consola do switch. Abres o terminal GtKterm, primes Enter para verificar que há ligação, depois podes seguir os passos abaixo.
Estes passos só precisam de ser feitos uma vez, não é para fazer em todos os tux's e não é preciso alterar cabos
Dar login no switch (slide 48):
»enable
»password: ****** (deve ser 8nortel, olha para a prateleira e confirma)
Criar VLAN (vlan20) (Slide 44):
»configure terminal
»vlan 20
»end
»show vlan id 20
Adicionar ports, Os valores das ports são os números que acendem ao ligar os cabos ao switch
Ligas as ports 1 e 2 á VLAN0
Add port 1 to vlan 20 (Slide 44):
»configure terminal
»interface fastethernet 0/1 (x/y ; x é o bloco, como só há um , o bloco é 0; y é o port mostrado no switch)
»switchport mode access
»switchport access vlan 20
»end
»show running-config interface fastethernet 0/1
»show interfaces fastethernet 0/1 switchport
Add port 2 to VLAN20:
»configure terminal
»interface fastethernet 0/2
»switchport mode access
»switchport access vlan 20
»end
Criar outra VLAN (vlan21):
»configure terminal
»vlan 21
»end
»show vlan id 21
Adiciona a porta do tux22, porta 3 .
Add port 3 to VLAN21:
»configure terminal
»interface fastethernet 0/3
»switchport mode access
»switchport access vlan 21
»end
Start capture at tuxy3.eth0
Antes de fazer a captura no wireshark, verifica que os pings que se vão fazer abaixo funcionam. assim que tudo bem, prepara os comandos nas consolas e podes começar a captura no WireShark.
No tux23, pingar o tux4:
ping 172.16.20.254
(deixa dar 10 pings e depois dá CTRL+C)
pingar o tux22:
ping 172.16.21.1
(deixa dar 10 pings e depois dá CTRL+C)
Parar a captura e guardar o ficheiro. Renomear para exp2_step5.pcapng
Antes de fazer estas capturas prepara o ping de baixo, depois segue estes passos:
- Em tux23 começar captura em eth0
- Passar para tux24
- Em tux24 começar captura em eth0
- Passar para tux22
- Em tux22 começar captura em eth0
No tux23, pingar em broadcast:
ping -b 172.16.20.255
(deixa dar 10 pings e depois dá CTRL+C)
- seria de esperar uma resposta do tux24, tal não acontece porque echo-ignore-broadcast está ativado por default
- para obter resposta no tux23, executar em tux24: echo 0 > /proc/sys/net/ipv4/icmp_echo_ignore_broadcasts
- Parar a captura em tux23
- Parar a captura em tux24
- Parar a captura em tux22
- Guardar o ficheiro de tux23 como
exp2_step7_tux23.pcapng
- Guardar o ficheiro de tux24 como
exp2_step7_tux24.pcapng
- Guardar o ficheiro de tux22 como
exp2_step7_tux22.pcapng
Antes de fazer estas capturas prepara o ping de baixo, depois segue estes passos:
- Em tux23 começar captura em eth0
- Passar para tux24
- Em tux24 começar captura em eth0
- Passar para tux22
- Em tux22 começar captura em eth0
No tux22, pingar em broadcast:
ping -b 172.16.21.255
(deixa dar 10 pings e depois dá CTRL+C)
- Parar a captura em tux23
- Parar a captura em tux24
- Parar a captura em tux22
- Guardar o ficheiro de tux23 como
exp2_step10_tux23.pcapng
- Guardar o ficheiro de tux24 como
exp2_step10_tux24.pcapng
- Guardar o ficheiro de tux22 como
exp2_step10_tux22.pcapng