Skip to content

DaneGardner/KKMulticontroller

 
 

Repository files navigation

KK board flight controller software for AVR microcontrollers

(re)written by Dane Gardner

Based on KK by Simon Kirby <https://github.com/sim-/kk>
Based on XXcontrol_KR_v1.5 by Minsoo Kim
Based on XXcontrol by Mike Barton
Based on excellent assembly code by Rolf R Bakke (kapteinkuk)
With ideas from Rune Hasvold (CyCrow) and OlliW on rcgroups
Thanks, everyone!

NO WARRANTY EXPRESSED OR IMPLIED. USE AT YOUR OWN RISK. Always test
without propellers! Please do not ship derivative works without
source; keep this code open as Rolf first so kindly released his
design and code to the community.

Should fit on 48, 88, 168, and 328. I've tested TRICOPTER mode on an
ATmega88A. You may wish to use avrdude -t to "dump calibration" and
check timings on a digital scope. Temperature and voltage shift the
oscillator frequency a little, and each chip responds differently.
See doc8271.pdf page 401.

I notice a few microseconds of output jitter still with the internal
oscillator. It seems that only an external resonator or crystal will
solve this, but those pins are currently used for Rx and the LED, and
the Rx pin cannot be moved to another pin that does not share another
PCINT unless RESET is used for that purpose. If using all hardware
PPM, it may be acceptable to have a more expensive interrupt handler
that simply logs the interrupt time and pin states and do the rest of
the processing in RxGetChannels().

See http://www.kkmulticopter.com/

Hardware PPM supported on motor outputs M1, M2, M5 and M6; software
PPM on M3 and M4 (Rx interrupts can cause some jitter). M3 and M4
outputs will be copied to M5 and M6, when not otherwise used, to allow
use of full hardware PPM.

General motor output setup:

Single
            M1 CCW
            |
            |

            M2 (Servo)
            |
            |
     M5 ---- ---- M3
    (Servo) | (Servo)
            |
            M4 (Servo)

Dual
            M1 CCW
            |
            M2 CW
            |

            |
            |
  M5/M3 ----+----
    (Servo) |
            |
         M6/M4 (Servo)

Twin
         / --- \
       /    |    \
     M1 CW  |     M2 CCW
            |
     M3     |       M4
   (Servo)  |   (Servo)
            |
            |
            M5 (Tail Servo, Optional)
            M6 (Tail Servo Reverse, Optional)

Tri
      M1 CW     M2 CCW
        \       /
         \.---./
          |   |
          `---'
            |
            |M4/M6 (Tail Servo)
            M3/M5 CCW

Quad-+
           M1 CW
            |
            |
            |
          .---.
M2 CCW----|   |----M3/M5 CCW
          `---'
            |
            |
            |
          M4/M6 CW

Quad-X

       M1 CW    M2 CCW
        \        /
          \.--./
           |  |
          /`--'\
        /        \
    M4/M6 CCW   M3/M5 CW

Hex
            M1 CW
            |
    M6 CCW  |     M2 CCW
      \     |     /
        \ .---. /
         -|   |-
        / `---' \
      /     |     \
    M5 CW   |     M3 CW
            |
            M4 CCW

Y6

     M1,4        M2,5    M1->3 = CW
        \       /        M4->6 = CCW
         \.---./
          |   |
          `---'
            |
            |
           M3,6

About

kkmulticopter flight controller software

Resources

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published

Languages

  • C 82.2%
  • Objective-C 17.8%