-
Notifications
You must be signed in to change notification settings - Fork 2
New issue
Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.
By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.
Already on GitHub? Sign in to your account
Problem with adding OP-TEE to venice #2
Comments
Paweł
Please send your question to ***@***.*** and/or the U-Boot
mailing list. Feel free to cc me. Secure boot and OP-TEE are a complicated
topic that is not well documented and how to use it differs depending on
the versions of ATF/OP-TEE/U-Boot you are using.
Best Regards,
Tim
Tim Harvey
Software Engineer
Gateworks Corporation
(805)781-2000 x18
3026 S. Higuera, San Luis Obispo, CA 93401
www.gateworks.com
…On Thu, Sep 29, 2022 at 6:44 AM Paweł Cichowski ***@***.***> wrote:
Hi there,
I am trying to add OP-TEE to Gateworks Venice GW73xx-0x i.MX8MM closely
following this wiki article: http://trac.gateworks.com/wiki/venice/tee. I
flash the firmware using the JTAG adapter. This problem is caused only when
using SPD=opteed as a make argument for atf.
The machine is getting stuck on U-Boot, DRAM: specifically, restarting
each time after a timeout.
Logs:
U-Boot SPL 2021.07-g54ac394a7c-dirty (Sep 29 2022 - 15:21:57 +0200)
GSCv3 : v57 0x12aa RST:VIN Thermal protection:disabled
RTC : 1970-01-01 0:15:35 UTC
Model : GW7300-00-B1B
Serial : 852419
MFGDate : 11-13-2020
PMIC : MP5416
DRAM : LPDDR4 1 GiB
WDT: Started with servicing (60s timeout)
Trying to boot from MMC1
DTB : imx8mm-venice-gw73xx-0x
NOTICE: BL31: v2.2(release):a9caa2cbe
NOTICE: BL31: Built : 15:21:54, Sep 29 2022
I/TC:
I/TC: Non-secure external DT found
I/TC: OP-TEE version: lf-5.10.52-2.1.0-rc2 (gcc version 10.4.0 (Buildroot 2022.05.2-207-g0d88416993)) #1 czw, 29 wrz 2022, 11:49:56 UTC aarch64
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
U-Boot 2021.07-g54ac394a7c-dirty (Sep 29 2022 - 15:21:57 +0200)
CPU: Freescale i.MX8MMQ rev1.0 1600 MHz (running at 1200 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 47C
Reset cause: POR
Model: Gateworks Venice GW73xx-0x i.MX8MM Development Kit
DRAM:
I do not know if this is a good place to ask, but no resources or
solutions online seem to resolve this issue.
Kind regards,
Paweł
—
Reply to this email directly, view it on GitHub
<#2>, or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ABAJETDPBH5SFGTS2X45QCDWAWMLDANCNFSM6AAAAAAQYZISYQ>
.
You are receiving this because you are subscribed to this thread.Message
ID: ***@***.***>
|
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
Hi there,
I am trying to add OP-TEE to
Gateworks Venice GW73xx-0x i.MX8MM
closely following this wiki article: http://trac.gateworks.com/wiki/venice/tee. I flash the firmware using the JTAG adapter. This problem is caused only when usingSPD=opteed
as a make argument for atf.The machine is getting stuck on U-Boot,
DRAM:
specifically, restarting each time after a timeout.Logs:
I do not know if this is a good place to ask, but no resources or solutions online seem to resolve this issue.
Kind regards,
Paweł
The text was updated successfully, but these errors were encountered: