-
-
Notifications
You must be signed in to change notification settings - Fork 5.1k
Commit
This commit does not belong to any branch on this repository, and may belong to a fork outside of the repository.
config: Ender 3 S1/S1 Pro Default Configurations (#5332)
Signed-off-by: Rob Casper <myallneedsemail@gmail.com>
- Loading branch information
Showing
3 changed files
with
266 additions
and
0 deletions.
There are no files selected for viewing
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
Original file line number | Diff line number | Diff line change |
---|---|---|
@@ -0,0 +1,132 @@ | ||
# This file contains pin mappings for the stock 2021 Creality Ender 3 | ||
# S1. To use this config, check the STM32 Chip on the V2.4S1 Board | ||
# then during "make menuconfig" select either the STM32F103 with a | ||
# "28KiB bootloader" or select the STM32F401 with a "64KiB bootloader" | ||
# and serial (on USB PA10/PA9) communication for both depending on the | ||
# STM32 Chip installed on your printers Motherboard. | ||
|
||
# If you prefer a direct serial connection, in "make menuconfig" | ||
# select "Enable extra low-level configuration options" and select | ||
# serial (on USB PA10/PA9), which is broken out on the 10 pin IDC | ||
# cable used for the LCD module as follows: | ||
# 3: Tx, 4: Rx, 9: GND, 10: VCC | ||
|
||
# Flash this firmware by copying "out/klipper.bin" to a SD card and | ||
# turning on the printer with the card inserted. The firmware | ||
# filename must changed to "firmware.bin" | ||
|
||
# See docs/Config_Reference.md for a description of parameters. | ||
|
||
[stepper_x] | ||
step_pin: PC2 | ||
dir_pin: PB9 | ||
enable_pin: !PC3 | ||
microsteps: 16 | ||
rotation_distance: 40 | ||
endstop_pin: !PA5 | ||
position_endstop: -10 | ||
position_max: 235 | ||
position_min: -15 | ||
homing_speed: 50 | ||
|
||
[stepper_y] | ||
step_pin: PB8 | ||
dir_pin: PB7 | ||
enable_pin: !PC3 | ||
microsteps: 16 | ||
rotation_distance: 40 | ||
endstop_pin: !PA6 | ||
position_endstop: -10 | ||
position_max: 241 | ||
position_min: -15 | ||
homing_speed: 50 | ||
|
||
[stepper_z] | ||
step_pin: PB6 | ||
dir_pin: !PB5 | ||
enable_pin: !PC3 | ||
microsteps: 16 | ||
rotation_distance: 8 | ||
endstop_pin: probe:z_virtual_endstop | ||
position_max: 270 | ||
position_min: -4 | ||
|
||
[extruder] | ||
step_pin: PB4 | ||
dir_pin: PB3 | ||
enable_pin: !PC3 | ||
microsteps: 16 | ||
gear_ratio: 3.5:1 | ||
rotation_distance: 26.3585 | ||
nozzle_diameter: 0.400 | ||
filament_diameter: 1.750 | ||
heater_pin: PA1 | ||
sensor_type: EPCOS 100K B57560G104F | ||
sensor_pin: PC5 | ||
control: pid | ||
pid_Kp: 23.561 | ||
pid_Ki: 1.208 | ||
pid_Kd: 114.859 | ||
min_temp: 0 | ||
max_temp: 250 | ||
|
||
[heater_bed] | ||
heater_pin: PA7 | ||
sensor_type: EPCOS 100K B57560G104F | ||
sensor_pin: PC4 | ||
control: pid | ||
pid_Kp: 71.867 | ||
pid_Ki: 1.536 | ||
pid_Kd: 840.843 | ||
min_temp: 0 | ||
max_temp: 110 | ||
|
||
[heater_fan hotend_fan] | ||
pin: PC0 | ||
heater: extruder | ||
heater_temp: 50.0 | ||
|
||
[fan] | ||
pin: PA0 | ||
|
||
[mcu] | ||
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0 | ||
restart_method: command | ||
|
||
[printer] | ||
kinematics: cartesian | ||
max_velocity: 300 | ||
max_accel: 2000 | ||
max_z_velocity: 5 | ||
max_z_accel: 100 | ||
|
||
[bltouch] | ||
sensor_pin: ^PC14 | ||
control_pin: PC13 | ||
x_offset: -31.8 | ||
y_offset: -40.5 | ||
z_offset: 0 | ||
probe_with_touch_mode: true | ||
stow_on_each_sample: false | ||
|
||
[bed_mesh] | ||
speed: 120 | ||
mesh_min: 20, 20 | ||
mesh_max: 200, 200 | ||
probe_count: 4,4 | ||
algorithm: bicubic | ||
|
||
[safe_z_home] | ||
home_xy_position: 147, 154 | ||
speed: 75 | ||
z_hop: 5 | ||
z_hop_speed: 5 | ||
move_to_previous: true | ||
|
||
[filament_switch_sensor e0_sensor] | ||
switch_pin: !PC15 | ||
pause_on_runout: true | ||
runout_gcode: PAUSE | ||
|
||
[pause_resume] | ||
recover_velocity: 25 |
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
Original file line number | Diff line number | Diff line change |
---|---|---|
@@ -0,0 +1,132 @@ | ||
# This file contains pin mappings for the stock 2022 Creality Ender 3 | ||
# S1 Pro. To use this config, check the STM32 Chip on the V2.4S1 Board | ||
# then during "make menuconfig" select either the STM32F103 with a | ||
# "28KiB bootloader" or select the STM32F401 with a "64KiB bootloader" | ||
# and serial (on USB PA10/PA9) communication for both depending on the | ||
# STM32 Chip installed on your printers Motherboard. | ||
|
||
# If you prefer a direct serial connection, in "make menuconfig" | ||
# select "Enable extra low-level configuration options" and select | ||
# serial (on USB PA10/PA9), which is broken out on the 10 pin IDC | ||
# cable used for the LCD module as follows: | ||
# 3: Tx, 4: Rx, 9: GND, 10: VCC | ||
|
||
# Flash this firmware by copying "out/klipper.bin" to a SD card and | ||
# turning on the printer with the card inserted. The firmware | ||
# filename must changed to "firmware.bin" | ||
|
||
# See docs/Config_Reference.md for a description of parameters. | ||
|
||
[stepper_x] | ||
step_pin: PC2 | ||
dir_pin: PB9 | ||
enable_pin: !PC3 | ||
microsteps: 16 | ||
rotation_distance: 40 | ||
endstop_pin: !PA5 | ||
position_endstop: -10 | ||
position_max: 235 | ||
position_min: -15 | ||
homing_speed: 50 | ||
|
||
[stepper_y] | ||
step_pin: PB8 | ||
dir_pin: PB7 | ||
enable_pin: !PC3 | ||
microsteps: 16 | ||
rotation_distance: 40 | ||
endstop_pin: !PA6 | ||
position_endstop: -10 | ||
position_max: 241 | ||
position_min: -15 | ||
homing_speed: 50 | ||
|
||
[stepper_z] | ||
step_pin: PB6 | ||
dir_pin: !PB5 | ||
enable_pin: !PC3 | ||
microsteps: 16 | ||
rotation_distance: 8 | ||
endstop_pin: probe:z_virtual_endstop | ||
position_max: 270 | ||
position_min: -4 | ||
|
||
[extruder] | ||
step_pin: PB4 | ||
dir_pin: PB3 | ||
enable_pin: !PC3 | ||
microsteps: 16 | ||
gear_ratio: 3.5:1 | ||
rotation_distance: 26.3585 | ||
nozzle_diameter: 0.400 | ||
filament_diameter: 1.750 | ||
heater_pin: PA1 | ||
sensor_type: EPCOS 100K B57560G104F | ||
sensor_pin: PC5 | ||
control: pid | ||
pid_Kp: 23.561 | ||
pid_Ki: 1.208 | ||
pid_Kd: 114.859 | ||
min_temp: 0 | ||
max_temp: 300 | ||
|
||
[heater_bed] | ||
heater_pin: PA7 | ||
sensor_type: EPCOS 100K B57560G104F | ||
sensor_pin: PC4 | ||
control: pid | ||
pid_Kp: 71.867 | ||
pid_Ki: 1.536 | ||
pid_Kd: 840.843 | ||
min_temp: 0 | ||
max_temp: 110 | ||
|
||
[heater_fan hotend_fan] | ||
pin: PC0 | ||
heater: extruder | ||
heater_temp: 50.0 | ||
|
||
[fan] | ||
pin: PA0 | ||
|
||
[mcu] | ||
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0 | ||
restart_method: command | ||
|
||
[printer] | ||
kinematics: cartesian | ||
max_velocity: 300 | ||
max_accel: 2000 | ||
max_z_velocity: 5 | ||
max_z_accel: 100 | ||
|
||
[bltouch] | ||
sensor_pin: ^PC14 | ||
control_pin: PC13 | ||
x_offset: -31.8 | ||
y_offset: -40.5 | ||
z_offset: 0 | ||
probe_with_touch_mode: true | ||
stow_on_each_sample: false | ||
|
||
[bed_mesh] | ||
speed: 120 | ||
mesh_min: 20, 20 | ||
mesh_max: 200, 200 | ||
probe_count: 4,4 | ||
algorithm: bicubic | ||
|
||
[safe_z_home] | ||
home_xy_position: 147, 154 | ||
speed: 75 | ||
z_hop: 5 | ||
z_hop_speed: 5 | ||
move_to_previous: true | ||
|
||
[filament_switch_sensor e0_sensor] | ||
switch_pin: !PC15 | ||
pause_on_runout: true | ||
runout_gcode: PAUSE | ||
|
||
[pause_resume] | ||
recover_velocity: 25 |
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters