Skip to content

Latest commit

 

History

History
 
 

OverSampling

Folders and files

NameName
Last commit message
Last commit date

parent directory

..
 
 
 
 
 
 
 
 

OverSampling

Medium Pins used Inclusion
ASK/FSK radio modules 1 or 2 #include <PJONOverSampling.h>

OverSampling is a software implementation of PJDLR (Padded Jittering Data Link over Radio). It supports simplex and half-duplex asynchronous serial communication and implements a carrier-sense, non-persistent random multiple access method (non-persistent CSMA). This implementation can run on limited microcontrollers with low clock accuracy, supports communication for many devices connected to the same medium and stable operation in spite of interference. Its procedure is a more efficient alternative to the LoRa Open Standard (that specifies a variation of Slotted ALOHA) and it is designed to obtain long range and high reliability using FSK, ASK or OOK modulation radio transceivers. Take a look at the video introduction for a brief showcase of its features.

Compatibility

MCU Clock Supported pins
ATmega88/168/328 (Duemilanove, Uno, Nano, Pro) 16MHz 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, A0, A1
ATmega16u4/32u4 (Leonardo, Micro) 16MHz 2, 4, 8, 12
ATmega2560 (Mega, Mega nano) 16MHz 3, 4, 7, 8, 9, 10, 12
ESP8266 80/160MHz D0 or GPIO 16, D1 or GPIO 5

Performance

  • Transfer speed: 202 B/s or 1620 Baud
  • Data throughput: 150 B/s
  • Range: 250 meters with no line of sight, 5 km with line of sight and ideal atmospheric conditions

Configuration

Before including the library it is possible to configure OverSampling using predefined constants:

Constant Purpose Supported value
OS_TIMEOUT Maximum latency Duration in microseconds (10000 by default)
OS_BACK_OFF_DEGREE Maximum back-off exponential degree Numeric value (5 by default)
OS_MAX_ATTEMPTS Maximum transmission attempts Numeric value (10 by default)

Use PJONOverSampling to instantiate a new PJON object ready to communicate using the OverSampling strategy. All the other necessary information is present in the general Documentation.

#include <PJONOverSampling.h>

PJONOverSampling bus;

void setup() {
  // Set the pin 12 as the communication pin
  bus.strategy.set_pin(12);

  // Set pin 11 as input pin and pin 12 as output pin
  bus.strategy.set_pins(11, 12);
}  

After the PJON object is defined with its strategy it is possible to set the communication pins using the setters described in the example below.

Use OverSampling with cheap 433MHz transceivers

To build an open-source PJON packet radio able to communicate up to 5 km away you need only a couple (for PJON_SIMPLEX mode) or two couples (for PJON_HALF_DUPLEX mode) of cheap 315/433MHz ASK/FSK/OOK transmitter and receiver modules (with a cost around 2/3 dollars each). Please be sure of the regulations your government imposes on radio transmission over these frequencies before use.

PJON Oversampling packet radio

The maximum detected range was experimented with a small packet radio transmitting its position every minute. The maximum range obtained was slightly more than 5 kilometers in line of sight in open area. Testing it instead in an urban environment the range is down to 250 meters. Two couples of STX882 and SRX882 were used as transceivers. If you choose these modules, remember to set HIGH the pin CS in the receiver module before starting reception.

Antenna design

Experiments in PJON_HALF_DUPLEX mode have shown that it seems better to keep isolated the two antennas, using two different, not connected elements to transmit and receive. The first suggested antenna design is a wide beam dipole antenna made by two 173mm (quarter wavelength) or 345mm (half wavelength) long conductors, one connected to ground and the other connected to the input or output pin:

173mm quarter wavelength / 345mm half wavelength

-------------------|--------------------
                 __|__
                |TX/RX|
                |_____|

A more directional, compact and long range antenna design is the wip antenna. Can be easily crafted with two 173mm (quarter wavelength) / 345mm (half wavelength) long insulated wire sections wrapped with each other every 5mm, one is connected to ground and the other to the input or output pin. This design helps because of its strong ground plane, often necessary to have decent results with this sort of hardware.

       5mm
        || 173mm quarter wavelength / 345mm half wavelength
GND   --\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\
RX/TX --/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/

Known issues

  • In older versions, OverSampling was affected by ineffective and short range if used in PJON_HALF_DUPLEX mode. This issue has been fixed by suggesting the use of pins part of 2 different port groups.

Safety warning

In all cases, when installing or maintaining a PJON network, extreme care must be taken to avoid any danger. Before any practical test or hardware purchase for a wireless OverSampling radio setup, compliance with government requirements and regulations must be ensured.