Sensirion Raspberry Pi I2C SCD30 Driver

This document explains how to set up a SCD30 sensor to run on a Raspberry Pi using the provided code.

Click here to learn more about the Sensirion SCD30 sensor.

The default I²C address of SCD30 is 0x61.

Setup Guide

Connecting the Sensor

Your sensor has the 5 different connectors: VDD, GND, SCL, SDA, SEL. Use the following pins to connect your SCD30:

SCD30	Cable Color	Raspberry Pi
VDD	red	Pin 1
GND	black	Pin 6
SCL	yellow	Pin 5
SDA	green	Pin 3
SEL	blue	Pin 9

Detaild sensor pinout

Pin	Cable Color	Name	Description	Comments
1	red	VDD	Supply Voltage	3.3 to 5.5V
2	black	GND	Ground
3	yellow	SCL	I2C: Serial clock input
4	green	SDA	I2C: Serial data input / output
5		RDY	High when data is available	do not connect
6		PWM		do not connect
7	blue	SEL	Interface select	Pull to ground or floating for I2C

Raspberry Pi

• Install the Raspberry Pi OS on to your Raspberry Pi

• Enable the I²C interface in the raspi-config

• Download the SCD30 driver from Github and extract the .zip on your Raspberry Pi

• Compile the driver

  1. Open a terminal

  2. Navigate to the driver directory. E.g. cd ~/raspberry-pi-i2c-scd30

  3. Run the make command to compile the driver

     Output:

     rm -f scd30_i2c_example_usage
     cc -Os -Wall -fstrict-aliasing -Wstrict-aliasing=1 -Wsign-conversion -fPIC -I. -o scd30_i2c_example_usage  scd30_i2c.h scd30_i2c.c sensirion_i2c_hal.h sensirion_i2c.h sensirion_i2c.c \
         sensirion_i2c_hal.c sensirion_config.h sensirion_common.h sensirion_common.c scd30_i2c_example_usage.c
     

• Test your connected sensor

  • Run ./scd30_i2c_example_usage in the same directory you used to compile the driver. You should see the measurement values in the console.

Troubleshooting

Building driver failed

If the execution of make in the compilation step 3 fails with something like

 make: command not found

your RaspberryPi likely does not have the build tools installed. Proceed as follows:

$ sudo apt-get update
$ sudo apt-get upgrade
$ sudo apt-get install build-essential

Initialization failed

If you run ./scd30_i2c_example_usage but do not get sensor readings but something like this instead

Error executing soft_reset(): -1
Error executing read_firmware_version(): -1
Error executing start_periodic_measurement(): -1
...

then go through the below troubleshooting steps.

• Ensure that you connected the sensor correctly: All cables are fully plugged in and connected to the correct pin.
• Ensure that I²C is enabled on the Raspberry Pi. For this redo the steps on "Enable the I²C interface in the raspi-config" in the guide above.
• Ensure that your user account has read and write access to the I²C device. If it only works with user root (sudo ./scd30_i2c_example_usage), it's typically due to wrong permission settings. See the next chapter how to solve this.

Missing I²C permissions

If your user is missing access to the I²C interface you should first verfiy the user belongs to the i2c group.

$ groups
users input some other groups etc

If i2c is missing in the list add the user and restart the Raspberry Pi.

$ sudo adduser your-user i2c
Adding user `your-user' to group `i2c' ...
Adding user your-user to group i2c
Done.
$ sudo reboot

If that did not help you can make globally accessible hardware interfaces with a udev rule. Only do this if everything else failed and you are reasoably confident you are the only one having access to your Pi.

Go into the /etc/udev/rules.d folder and add a new file named local.rules.

$ cd /etc/udev/rules.d/
$ sudo touch local.rules

Then add a single line ACTION=="add", KERNEL=="i2c-[0-1]*", MODE="0666" to the file with your favorite editor.

$ sudo vi local.rules

Contributing

Contributions are welcome!

We develop and test this driver using our company internal tools (version control, continuous integration, code review etc.) and automatically synchronize the master branch with GitHub. But this doesn't mean that we don't respond to issues or don't accept pull requests on GitHub. In fact, you're very welcome to open issues or create pull requests :)

This Sensirion library uses clang-format to standardize the formatting of all our .c and .h files. Make sure your contributions are formatted accordingly:

The -i flag will apply the format changes to the files listed.

clang-format -i *.c *.h

Note that differences from this formatting will result in a failed build until they are fixed.

License

See LICENSE.