Warning: v6.1.0 - be aware that many commands have been removed from minimal version

[arendst]

@reloxx13 in order to get a useable size for the minimal version I had to remove commands normally not needed during OtaMagic. I verified this and OtaMagic still worked as expected.

In the first release I also disabled HTTPCommand as it is not needed with Tasmota OtaMagic too.

It appears that TasmoAdmin does OTA updates WITHOUT using OtaMagic and tries to change the otaurl during an update from one version to another. As HTTPCommands was disabled this failed as users noticed by issues arendst/Tasmota#3144 (comment) and #165.

I just re-enabled HTTPCommand in the minimal version in the latest release (still v6.1.0) at the cost of just 1k but still be aware that many commands have been disabled. For your information see sonoff.ino regarding available commands during minimal firmware active:

#ifdef BE_MINIMAL
enum TasmotaCommands {
  CMND_POWER, CMND_FANSPEED, CMND_STATUS, CMND_STATE, CMND_SLEEP, CMND_UPGRADE, CMND_UPLOAD, CMND_OTAURL, CMND_SERIALLOG, CMND_RESTART };
const char kTasmotaCommands[] PROGMEM =
  D_CMND_POWER "|" D_CMND_FANSPEED "|" D_CMND_STATUS "|" D_CMND_STATE "|" D_CMND_SLEEP "|" D_CMND_UPGRADE "|" D_CMND_UPLOAD "|" D_CMND_OTAURL "|" D_CMND_SERIALLOG "|" D_CMND_RESTART;
#else
enum TasmotaCommands {
  CMND_BACKLOG, CMND_DELAY, CMND_POWER, CMND_FANSPEED, CMND_STATUS, CMND_STATE, CMND_POWERONSTATE, CMND_PULSETIME,
  CMND_BLINKTIME, CMND_BLINKCOUNT, CMND_SENSOR, CMND_SAVEDATA, CMND_SETOPTION, CMND_TEMPERATURE_RESOLUTION, CMND_HUMIDITY_RESOLUTION,
  CMND_PRESSURE_RESOLUTION, CMND_POWER_RESOLUTION, CMND_VOLTAGE_RESOLUTION, CMND_CURRENT_RESOLUTION, CMND_ENERGY_RESOLUTION, CMND_MODULE, CMND_MODULES,
  CMND_GPIO, CMND_GPIOS, CMND_PWM, CMND_PWMFREQUENCY, CMND_PWMRANGE, CMND_COUNTER, CMND_COUNTERTYPE,
  CMND_COUNTERDEBOUNCE, CMND_SLEEP, CMND_UPGRADE, CMND_UPLOAD, CMND_OTAURL, CMND_SERIALLOG, CMND_SYSLOG,
  CMND_LOGHOST, CMND_LOGPORT, CMND_IPADDRESS, CMND_NTPSERVER, CMND_AP, CMND_SSID, CMND_PASSWORD, CMND_HOSTNAME,
  CMND_WIFICONFIG, CMND_FRIENDLYNAME, CMND_SWITCHMODE,
  CMND_TELEPERIOD, CMND_RESTART, CMND_RESET, CMND_TIMEZONE, CMND_TIMESTD, CMND_TIMEDST, CMND_ALTITUDE, CMND_LEDPOWER, CMND_LEDSTATE,
  CMND_I2CSCAN, CMND_SERIALSEND, CMND_BAUDRATE, CMND_SERIALDELIMITER };
const char kTasmotaCommands[] PROGMEM =
  D_CMND_BACKLOG "|" D_CMND_DELAY "|" D_CMND_POWER "|" D_CMND_FANSPEED "|" D_CMND_STATUS "|" D_CMND_STATE "|"  D_CMND_POWERONSTATE "|" D_CMND_PULSETIME "|"
  D_CMND_BLINKTIME "|" D_CMND_BLINKCOUNT "|" D_CMND_SENSOR "|" D_CMND_SAVEDATA "|" D_CMND_SETOPTION "|" D_CMND_TEMPERATURE_RESOLUTION "|" D_CMND_HUMIDITY_RESOLUTION "|"
  D_CMND_PRESSURE_RESOLUTION "|" D_CMND_POWER_RESOLUTION "|" D_CMND_VOLTAGE_RESOLUTION "|" D_CMND_CURRENT_RESOLUTION "|" D_CMND_ENERGY_RESOLUTION "|" D_CMND_MODULE "|" D_CMND_MODULES "|"
  D_CMND_GPIO "|" D_CMND_GPIOS "|" D_CMND_PWM "|" D_CMND_PWMFREQUENCY "|" D_CMND_PWMRANGE "|" D_CMND_COUNTER "|"  D_CMND_COUNTERTYPE "|"
  D_CMND_COUNTERDEBOUNCE "|" D_CMND_SLEEP "|" D_CMND_UPGRADE "|" D_CMND_UPLOAD "|" D_CMND_OTAURL "|" D_CMND_SERIALLOG "|" D_CMND_SYSLOG "|"
  D_CMND_LOGHOST "|" D_CMND_LOGPORT "|" D_CMND_IPADDRESS "|" D_CMND_NTPSERVER "|" D_CMND_AP "|" D_CMND_SSID "|" D_CMND_PASSWORD "|" D_CMND_HOSTNAME "|"
  D_CMND_WIFICONFIG "|" D_CMND_FRIENDLYNAME "|" D_CMND_SWITCHMODE "|"
  D_CMND_TELEPERIOD "|" D_CMND_RESTART "|" D_CMND_RESET "|" D_CMND_TIMEZONE "|" D_CMND_TIMESTD "|" D_CMND_TIMEDST "|" D_CMND_ALTITUDE "|" D_CMND_LEDPOWER "|" D_CMND_LEDSTATE "|"
  D_CMND_I2CSCAN "|" D_CMND_SERIALSEND "|" D_CMND_BAUDRATE "|" D_CMND_SERIALDELIMITER;
#endif

[reloxx13]

Thank you for the hint, ill adjust it to that ota magic, that it loads the minimal automated.

[reloxx13]

fixed it, but travis fails x.x

[RaymondMouthaan]

@reloxx13 docker image build has been fixed ;)