walksnail avatar OSD

[wizzzz0]

Describe the bug

walksnail avatar elements do not line up with the osd image on betaflight they are down and to the right , also the clicking the hd doses not make a diffrence

To Reproduce

Expected behavior

Should work like the dji msp osd

Support ID

Id: "aceafddc-2265-499c-a625-803b5def4a8a"

Diff configuration

# version
# Betaflight / STM32F7X2 (S7X2) 4.4.0 Jan 17 2023 / 04:30:33 (a7cf8f0c6) MSP API: 1.45

# config: YES

# start the command batch
batch start

board_name SPEEDYBEEF7V3
manufacturer_id SPBE

# feature
feature -TELEMETRY
feature ESC_SENSOR

# serial
serial 0 131073 115200 57600 0 115200

# aux
aux 0 0 0 1900 2100 0 0
aux 1 1 1 1900 2100 0 0
aux 2 13 2 1700 2100 0 0

# master
set gyro_lpf2_static_hz = 1000
set dyn_notch_count = 2
set dyn_notch_q = 400
set dyn_notch_max_hz = 800
set gyro_lpf1_dyn_min_hz = 300
set gyro_lpf1_dyn_max_hz = 600
set gyro_lpf1_dyn_expo = 8
set acc_lpf_hz = 10
set acc_calibration = -32,-58,0,1
set dshot_bidir = ON
set motor_pwm_protocol = DSHOT600
set deadband = 2
set yaw_deadband = 2
set simplified_gyro_filter = OFF
set osd_vbat_pos = 14818
set osd_flymode_pos = 6151
set osd_ah_pos = 2159
set osd_warnings_pos = 14699
set osd_avg_cell_voltage_pos = 6632
set osd_battery_usage_pos = 14347
set osd_disarmed_pos = 14833
set osd_efficiency_pos = 14844
set osd_displayport_device = MSP
set vcd_video_system = HD
set rpm_filter_harmonics = 1

profile 0

# profile 0
set dterm_lpf1_dyn_min_hz = 0
set dterm_lpf1_dyn_max_hz = 0
set dterm_lpf1_dyn_expo = 0
set dterm_lpf1_static_hz = 80
set dterm_lpf2_static_hz = 140
set p_pitch = 54
set i_pitch = 72
set d_pitch = 35
set f_pitch = 112
set p_roll = 51
set i_roll = 69
set d_roll = 33
set f_roll = 108
set p_yaw = 51
set i_yaw = 69
set f_yaw = 108
set d_min_roll = 33
set d_min_pitch = 35
set feedforward_smooth_factor = 30
set feedforward_jitter_factor = 9
set simplified_i_gain = 75
set simplified_d_gain = 110
set simplified_pi_gain = 115
set simplified_dmax_gain = 0
set simplified_feedforward_gain = 90
set simplified_pitch_d_gain = 95
set simplified_dterm_filter = OFF

rateprofile 0

# rateprofile 0
set throttle_limit_percent = 95

# end the command batch
batch end

Resources configuration

A00: FREE
A01: SERIAL_RX 4
A02: SERIAL_TX 2
A03: SERIAL_RX 2
A04: FREE
A05: SPI_SCK 1
A06: SPI_MISO 1
A07: SPI_MOSI 1
A08: FREE
A09: SERIAL_TX 1
A10: SERIAL_RX 1
A11: USB
A12: USB
A13: LED 2
A14: LED 1
A15: MOTOR 1
B00: FREE
B01: FREE
B02: PREINIT 1
B03: MOTOR 2
B04: MOTOR 3
B05: FREE
B06: MOTOR 4
B07: FREE
B08: I2C_SCL 1
B09: I2C_SDA 1
B10: FREE
B11: FREE
B12: PREINIT 4
B13: SPI_SCK 2
B14: SPI_MISO 2
B15: SPI_MOSI 2
C00: FREE
C01: ADC_CURR
C02: ADC_BATT
C03: GYRO_EXTI
C04: FREE
C05: FREE
C06: FREE
C07: FREE
C08: FREE
C09: PINIO 1
C10: SPI_SCK 3
C11: SPI_MISO 3
C12: SPI_MOSI 3
C13: BEEPER
C14: FREE
C15: GYRO_CS 2
D00: FREE
D01: FREE
D02: SDCARD_CS
D03: FREE
D04: FREE
D05: FREE
D06: FREE
D07: FREE
D08: FREE
D09: FREE
D10: FREE
D11: FREE
D12: FREE
D13: FREE
D14: FREE
D15: FREE
E00: FREE
E01: FREE
E02: FREE
E03: FREE
E04: FREE
E05: FREE
E06: FREE
E07: FREE
E08: FREE
E09: FREE
E10: FREE
E11: FREE
E12: FREE
E13: FREE
E14: FREE
E15: FREE
F00: FREE
F01: FREE
F02: FREE
F03: FREE
F04: FREE
F05: FREE
F06: FREE
F07: FREE
F08: FREE
F09: FREE
F10: FREE
F11: FREE
F12: FREE
F13: FREE
F14: FREE
F15: FREE

Currently active Timers:
-----------------------
TIM1: FREE
TIM2: FREE
TIM3: FREE
TIM4: FREE
TIM5: FREE
TIM6: FREE
TIM7: FREE
TIM8:
    CH3 : DSHOT_BITBANG 1
    CH4 : DSHOT_BITBANG 2
TIM9: FREE
TIM10: FREE
TIM11: FREE
TIM12: FREE
TIM13: FREE
TIM14: FREE

Currently active DMA:
--------------------
DMA1 Stream 0: SPI_MISO 3
DMA1 Stream 1: FREE
DMA1 Stream 2: FREE
DMA1 Stream 3: FREE
DMA1 Stream 4: FREE
DMA1 Stream 5: SPI_MOSI 3
DMA1 Stream 6: FREE
DMA1 Stream 7: FREE
DMA2 Stream 0: ADC
DMA2 Stream 1: FREE
DMA2 Stream 2: SPI_MISO 1
DMA2 Stream 3: SPI_MOSI 1
DMA2 Stream 4: DSHOT_BITBANG 1
DMA2 Stream 5: FREE
DMA2 Stream 6: FREE
DMA2 Stream 7: DSHOT_BITBANG 2

Flight controller

speedy bee v3

Other components

No response

How are the different components wired up

No response

Add any other context about the problem that you think might be relevant here

No response

[SteveCEvans]

Correct. I’m working with Walksnail, but please don’t expect much due to the New Year. Currently WTFOS and HDZero support the declaration of canvas size, with position-able system OSD elements being worked on I believe. Colour text for warnings etc. is still in the pipeline.

[wizzzz0]

Perfect thanks for the update

[howels]

@wizzzz0 you may wish to try out a more recent firmware. HD OSD is available on 29.33.16 I believe which is now the Caddx page: https://caddxfpv.com/pages/download
You may need to align the OSD area with the goggles screen using the goggles settings as the HD OSD is initially offset too far right & down. There's a OSD position setting in the goggles to adjust.

[wizzzz0]

@howels thanks for the info all sorted now cheers

[howels]

Please close if this is sorted out, thanks

[github-actions]

This issue has been automatically marked as stale because it has not had recent activity. It will be closed if no further activity occurs within a week.

[github-actions]

Issue closed automatically as inactive.