Skip to content

Performance Options

Starfire13 edited this page Dec 29, 2023 · 11 revisions

Below are some of the settings that you can try adjusting to optimize the performance of your Liberation campaign.

Given the wide amount of differences between systems, it will take some trial and error for you to find the settings that work for your campaign. Don't be afraid to test out different settings to see how they impact your game!

Distant Unit Culling

Enabling "Culling of distant units" in the Mission Generator settings can improve performance by removing some distant units from the game. Note that with the implementation of multi-threading in DCS, culling is no longer as necessary nor as impactful of a performance boost as it once was, as baseline performance has improved significantly. If you are having performance problems, the most effective way to improve performance is by reducing the number of air units (reduce number of squadrons and/or reduce number of aircraft in squadrons) rather than using culling.

Picture of culling options

Distant unit culling removes all ground units (including buildings) that are beyond the set range from any culling exclusion zone. These culling exclusion zones are placed:

  • At the front line and its attached airfields, if a front line exists.
  • At the closest two opposing airfields, if no front line exists.
  • At all non-BARCAP mission targets.

Culling exclusion zones can be displayed on the map using the "Display Culling Zones" display option in the Liberation toolbar. If set too large, culling will have little effect. If set too small, the game experience will suffer as many SAMs will likely be culled.

Air units are never culled. Restricting departure airfields for air units does little to limit unit counts, so does not help performance. Instead, the income scale modifiers can be used to limit the amount of aircraft the AI is able to purchase.

Budget

The starting budget and income multiplier not only affects the difficulty of your campaign but it can have a dramatic impact on performance in your campaign. If you are finding that the default values are causing too much of a burden on your campaign, try adjusting them down. If you already see a negative performance impact in your first turn flying a mission, try lowering the starting budget and re-generating the campaign.

The starting budget and income multiplier is set during the initial campaign generation. During the campaign, you can still adjust both your and the enemy's income multiplier in the settings menu.

Miscellaneous Performance Options

In addition to unit culling and budget management, the mission generator page in the settings menu gives you a few more options.

Smoke visual effect on frontline: can have a big framerate impact if you are looking directly at it. If you regularly perform CAS and notice a drop in framerates while you are over the frontlines, consider turning this option off.

Convoys drive the full distance between control points is a performance option which will limit the length of the convoy routes, when the setting is disabled (it's enabled by default). DCS ground vehicle pathfinding AI is CPU heavy, especially when traversing long distances or when having to avoid obstacles and buildings, so this setting aims to help with campaigns which have a lot of ground vehicles between control points. Often the vehicles will not be able to traverse the entire length of the supply route during the mission, so running pathfinding for the whole route will be unnecessary.

Generate infantry squads along vehicles: More units usually equals more resources required. Infantry does not count towards the behind-the-scenes determination of a frontline victory/loss so removing them will not affect gameplay. Note: manpads will still spawn when this option is still turned off if you have the Manpads on frontline option checked.

Include destroyed units carcass: Another case where more units equals more resources required. Unchecking this box will remove dead units and should help improve performance.

Skynet IADS Script

Using Skynet can actually help improve performance as it manages most of the SAMs in the campaign and keeps them shut off until an enemy unit is within a pre-determined firing range. In doing so, it helps by saving some processing power that would otherwise be used to keep all the SAMs operating all the time.

Tacview

Disabling Tacview has resulted in framerate increases for a number of Liberation users. Most users report single digit frame increases but a few users have also experienced double digit gains. Consider turning Tacview off when running Liberation missions if you have already exhausted all other options and still need a few more frames to make your campaign playable.

Use a Dedicated Server

Users have also reported that setting up a dedicated server even on a local machine has helped improve their performance. Refer to the Dedicated Server Guide wiki page for more information on how to set a server up.

Clone this wiki locally