Open source firmware TSDZ2-v20.1C.4-LCD3 update 3

TSDZ2 Open Source Firmware v20.1C.4-update-3 for KT-LCD3 display

List of changes:
1 - Added "Walk Assist" speed settings, one for each level.
2 - Added motor overcurrent check (by mspider65), 07 Overcurrent error.
3 - Irq uart priority level set

ATTENTION! Newer KT-LCD3 displays may not be compatible with this firmware.

Open source firmware TSDZ2-v20.1C.4-LCD3 update 1

ATTENTION! Newer KT-LCD3 displays may not be compatible with this firmware.

TSDZ2 Open Source Firmware v20.1C.4 for KT-LCD3 display

1 - Added Peep optimization in Makefile (TSDZ2 only).

Open source firmware TSDZ2-v20.1C.4-LCD3

ATTENTION! Newer KT-LCD3 displays may not be compatible with this firmware.

TSDZ2 Open Source Firmware v20.1C.4 for KT-LCD3 display

1 - Improved torque sensor calibration.
2 - Added adjustment of the adc offset of the pedal torque.
3 - Added adjustment of the adc range of the pedal torque.
4 - Added adjustment of the adc angle of the pedal torque.
5 - Added choice Startup boost mode, at zero cadence or at zero speed.
6 - Added "Walk Assist" speed settings, one for each level.
7 - Added "Startup assist", to start from a standstill on difficult climbs.
8 - Improved progressivity in "Cadence Assist" mode.
9 - Added choice of soc % calculation mode.
10 - Added voltage calibration to display.
11 - Modified standing start, softer.
12 - Fixed an overflow issue in power assist mode.
13 - Fix of the calculation of human power.
14 - Changed "dead time" value to 2.0 us.

Wiki for this version: https://github.com/emmebrusa/TSDZ2-Smart-EBike-LCD3/blob/master/manuals/Wiki%20KT%20LCD3%20TSDZ2%20V20.1C.4.pdf

Open source firmware TSDZ2-v20.1C.3-LCD3

Open source firmware TSDZ2-v20.1C.3 for LCD3 display

1 - Updated to v12 version of mspider65 (Hall sensor calibration missing)
2 - Updated to v13 version of mspider65 (but with 19KHz PWM frequency)
3 - Improved motor efficiency with high power (by mspider65)
4 - Improved the problem of delay in restarting with bike in motion (from mspider65 v12)
5 - Improved standing start response.
6 - Decreased eMTB torque offset, it was too sensitive at the start.
7 - Added "Motor deceleration" adjustable 0-100%, (100% = fast stop).
8 - Speed sensor error threshold time increased (E08).
9 - Added enable / disable "Field Weakening".

Wiki for this version https://github.com/emmebrusa/TSDZ2-Smart-EBike-LCD3/wiki

Full Wiki https://github.com/bbeschea/TSDZ2_wiki/wiki/KT-LCD3-TSDZ2-V20.1C

Open source firmware TSDZ2-v20.1C-LCD3

Open source firmware TSDZ2-v20.1C-LCD3
1 - Added field weakening function to increase the motor speed (by mspider65).
2 - Added other optimizations to motor control, torque sensor and cadence sensor (by mspider65).
3 - Added startup boost function in POWER assist mode, enable/disable and parameters at display.
4 - Added HYBRID assist mode, TORQUE + POWER, can be set on the display.
5 - Added eMTB mode on multiple levels, can be set on the display.
6 - Improved "Start-up without pedal rotation" function.
7 - Added a filter to the speed sensor to avoid problems of adjusting the distance from the magnet.
8 - Added error E08 due to speed sensor failure or missing magnet.
9 - Added error E03 cadence sensor failure.
10 - Added error E01 overvoltage.
11 - Added error E09 write eeprom problem.
12 - Added "Assist with sensors error" function, to force assistance with sensors problem.

Wiki for this version: https://github.com/emmebrusa/TSDZ2-Smart-EBike-LCD3/wiki

Full Wiki https://github.com/bbeschea/TSDZ2_wiki/wiki/KT-LCD3-TSDZ2-V20.1C