CFAST – Consolidated Model of Fire Growth and Smoke Transport (Version 6) Software Development and Model Evaluation Guide

[FireStudent321]

Hi All,

I'm just wondering where I could find the raw data for NBS Multi-Compartment Test Series. I think these are plotted in graphs in CFAST Handbook Guide (section B.6, page 162-165). Am I right to think that the graphs show the average hot gas layer temperature vs. time for experiments? However, I couldn't find exactly where the raw data are that were used to plot the graphs.

CFAST Handbook Guide Link: https://nvlpubs.nist.gov/nistpubs/specialpublications/nist.sp.1086r1.pdf

I'm aware that the experimental set-up is taken from "An Experimental Data Set for the Accuracy Assessment of Room Fire Models" report. However, I've noticed that in the "An Experimental Data Set for the Accuracy Assessment of Room Fire Models" report, there are no results for each of the tree. But in CFAST Handbook Guide there are but not sure where it came from. Also, I don't know where the raw data are for each of the thermocouples are. I'm hoping someone would be able to point me in the right direction.

Thanks.

[drjfloyd]

Validaton data is archived here:

https://github.com/firemodels/out

[FireStudent321]

Hi Dr. Floyd,

Thanks for the reply. Is the output from the FDS model? I was hoping for the experimental raw data. I couldn't find the raw data from "An Experimental Data Set for the Accuracy Assessment of Room Fire Models" report and "An Experimental Data Set for the Accuracy Assessment of Room Fire Models" report.

[drjfloyd]

sorry posted the wrong link. I meant to post exp instead of out.

[FireStudent321]

No problem. What link can I find the experimental rata data on?

[gforney]

https://github.com/firemodels/exp

…

On Sun, Feb 25, 2024 at 9:11 PM FireStudent321 ***@***.***> wrote: No problem. What link can I find the experimental rata data on? — Reply to this email directly, view it on GitHub <#2086 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AC6UCRUWAKVQ4D4M4W3FIS3YVPVMPAVCNFSM6AAAAABDYQABRWVHI2DSMVQWIX3LMV43SRDJONRXK43TNFXW4Q3PNVWWK3TUHM4DKOBWHAZTA> . You are receiving this because you are subscribed to this thread.Message ID: ***@***.***>

-- Glenn Forney

[FireStudent321]

Thanks for the reply, Dr. Forney.

I just have a few questions to ask about NBS_MV100A.csv:

• I was just wondering what the -10, -20, -30, -40, -50, -60 meant under the heading "time";
• Also, I was wondering if the T#1 6, T#1 14, T#1 26, T#1 38, T#1 50, T#1 62, T#1 74, T#1 80 and T#1 84 corresponds to the 9
  thermocouples (of tree 1) at 0.15, 0.36, 0.66, 0.97, 1.27, 1.57, 1.88, 2.03 and 2.15m from floor, respectively.

[drjfloyd]

Time is the time in s. The data is 60 s of background data followed by fire ignition at 0 s.

6 in. = 15 cm
14 in. = 36 cm
etc.

[FireStudent321]

Thanks, Dr. Floyd.

[FireStudent321]

Hi,

Is there a particular reason why the report states that the ambient temperature is 22 degree celsius for MV100Z when the thermocouples read different temperatures at 0 seconds as per the link? The air temperature even reached 49 degree celsius in the fire room (tree 1) at 0 seconds. Where did they get the 22 degree celsius from? Have they taken the lowest air temperature at 0 seconds?

Link: https://github.com/firemodels/exp/blob/master/NBS_Multi-Room/NBS_MV100Z.csv

I'm just trying to understand why the starting air temperature of the experiment is higher than the starting air temperature of FDS.

Thanks.

[drjfloyd]

These tests were a set of compartments built inside of a larger room. I suspect this it that the larger room temperature was 22 C and multiple tests were run in the same day. Most of the TCs are within a few degrees of 22 C. The exception is the upper TCs in the fire room.