update vtol documents

docs/MixerProfile.md

@@ -1,96 +1,45 @@
 # MixerProfile
 
-A MixerProfile is a set of motor mixer, servo-mixer and platform type configuration settings to enable VTOL transitions.
+A MixerProfile is a set of motor mixer, servo-mixer and platform type configuration settings. It is designed for experienced inav users.
 
-Currently two profiles are supported on targets other than F411 and F722 (due to resource constraints on these FC). i.e VTOL transition is not available on  F411 and F722 targets.
+### For a tutorial of vtol setup, Read https://github.com/iNavFlight/inav/blob/master/docs/VTOL.md
 
-By default, switching between profiles requires reboot to take affect. However, when all conditions are met, and a suitable [configuration](#configuration) has been applied, `mixer_profile` also  allows in-flight profile [switching](#rc-mode-settings) to allow things like VTOL operation. This is the recommended operating mode.
+Not limited to VTOL. air/land/sea mixed vehicle is also achievable with this feature. Model behaves according to current mixer_profile's platform_type and configured custom motor/servo mixer
 
-Please note that this is an emerging / experimental capability that will require some effort by the pilot to implement.
-
-## Setup for VTOL
-- A VTOL specific FC target or `timer_output_mode` overrides was required in the early stage of the development, But since unified mapping introduced in INAV 7.0 It is not needed anymore.
-- ~~For mixer profile switching it is necessary to keep motor and servo PWM mapping consistent between Fixed-Wing (FW) and Multi-rotor (MR) profiles~~
-- ~~Traditionally, FW and MR have had different enumerations to define the PWM mappings. For VTOL operation it is necessary to set the `timer_output_mode` overrides to allow a consistent enumeration and thus mapping between MR and FW modes.~~
-- ~~In operation, it is necessary to set the `mixer_profile` and the `pid_profile` separately and to set a [RC mode](#rc-mode-settings) to switch between them.~~
-## Configuration
-### Timer overrides
-Set the timer overrides for the outputs that you are intended to use.
-For SITL builds, is not necessary to set timer overrides.
-Please note that there are some display issues on the configurator that will show wrong mapping on the mixer_profile which has less motor/servo compared with the another
-### Profile Switch
-
-Setup the FW mode and MR mode separately in two different mixer profiles:
-
-In this example, FW mode is `mixer_profile` 1 and MR mode is `mixer_profile` 2.
-
-Currently, the INAV Configurator does not fully support `mixer_profile`, so some of the settings have to be done in CLI.
-
-Add `set mixer_pid_profile_linking = ON` in order to enable `pid_profile` auto handling. It will change the `pid profile` index according to the `mixer_profile` index on FC boot and allow `mixer_profile` hot switching (this is recommended usage).
-
-The following 2 `mixer_profile` sections are added in the CLI:
-
-```
-#switch to mixer_profile by cli
-mixer_profile 1
-
-set platform_type = AIRPLANE
-set model_preview_type = 26
-# motor stop feature have been moved to here
-set motorstop_on_low = ON
-# enable pid_profile auto handling (recommended).
-set mixer_pid_profile_linking = ON
-save
-```
-Then finish the aeroplane setting on mixer_profile 1
-
-```
-mixer_profile 2
-
-set platform_type = TRICOPTER
-set model_preview_type = 1
-# also enable pid_profile auto handling
-set mixer_pid_profile_linking = ON
-save
-```
-Then finish the multi-rotor setting on `mixer_profile` 2.
+Currently two profiles are supported on targets other than F411(due to resource constraints on F411). i.e VTOL transition is not available on F411.
 
-Note that default profile is profile `1`.
+For VTOL setup. one mixer_profile is used for multi-rotor(MR) and the other is used for fixed-wing(FW)
+By default, switching between profiles requires reboot to take affect. However, using the RC mode: `MIXER PROFILE 2` will allow in flight switching for things like VTOL operation
+. And will re-initialize pid and navigation controllers for current MC or FW flying mode.
 
-You can use `MAX` servo input to set a fixed input for the tilting servo. Speed setting for `MAX` input is available in the CLI.
-
-It is recommended to have some amount of control surface (elevon / elevator) mapped for stabilization even in MR mode to get improved authority when airspeed is high.
-
-**Double check all settings in CLI with the `diff all` command**; make sure you have set the correct settings. Also check what will change with `mixer_profile`. For example servo output min / max range will not change. But `smix` and `mmix` will change.
+Please note that this is an emerging / experimental capability that will require some effort by the pilot to implement.
 
-### Mixer Transition input
+## Mixer Transition input
 
 Typically, 'transition input' will be useful in MR mode to gain airspeed.
-Both the servo mixer and motor mixer can accept transition mode as an input.
 The associated motor or servo will then move accordingly when transition mode is activated.
 Transition input is disabled when navigation mode is activate
 
 The use of Transition Mode is recommended to enable further features and future developments like fail-safe support. Mapping motor to servo output, or servo with logic conditions is **not** recommended
 
-#### Servo
+## Servo
 
-38 is the input source for transition input; use this to tilt motor to gain airspeed.
+`Mixer Transition` is the input source for transition input; use this to tilt motor to gain airspeed.
 
 Example: Increase servo 1 output by +45 with speed of 150 when transition mode is activated for tilted motor setup:
 
 ```
 # rule no; servo index; input source; rate; speed; activate logic function number
 smix 6 1 38 45 150 -1
 ```
-Please note there will be a time window that tilting motors is providing up lift but rear motor isn't. Result in a sudden pitch raise on the entering of the mode. More forward tilting servo position on transition input(you can use 'speed' in servo rules to slowly move to this position), A faster tilting servo speed on `MAX` servo input will reduce the time window. OR lower the throttle on the entering of the FW mode to mitigate the effect.
 
-#### Motor
+## Motor
 
-The default `mmix` throttle value is 0.0, It will not show in `diff` command when throttle value is 0.0 (unused); this causes the motor to stop.
+The default `mmix` throttle value is 0.0, It will not show in `diff` command when throttle value is 0.0 (unused);
 
 - 0.0<throttle<=1.0 : normal mapping
-- -1.0<throttle<=0.0 : motor stop, default value 0
-- -2.0<throttle<-1.0 : spin regardless of the radio's throttle position at speed `abs(throttle)-1` when Mixer Transition is activated.
+- -1.0<throttle<=0.0 : motor stop, default value 0, set to -1 to use a place holder for subsequent motor rules
+- -2.0<throttle<-1.0 : spin regardless of throttle position at speed `abs(throttle)-1` when Mixer Transition is activated.
 
 Example: This will spin motor number 5 (counting from 1) at 20%, in transition mode only, to gain speed for a "4 rotor 1 pusher" setup:
 
@@ -99,14 +48,13 @@ Example: This will spin motor number 5 (counting from 1) at 20%, in transition m
 mmix 4 -1.200  0.000  0.000  0.000
 ```
 
-### RC mode settings
+## RC mode settings
 
 It is recommend that the pilot uses a RC mode switch to activate modes or switch profiles.
-Profile files Switching is not available until the runtime sensor calibration is done. Switching is NOT available when navigation mode is activate or position controller is activate, including altitude hold.
+Profile files Switching is not available until the runtime sensor calibration is done. Switching is NOT available when navigation mode is activate.
 
-`mixer_profile` 1 will be used as default, `mixer_profile` 2 will be used when the `MIXER PROFILE 2` mode box is activated. Once successfully set, you can see the profiles / model preview etc. will switch accordingly when you view the relevant INAV Configurator tabs. Checking these tabs in the INAV Configurator will help make the setup easier.
-
-Set `MIXER TRANSITION` accordingly when you want to use `MIXER TRANSITION` input for motors and servos. Here is sample of using the `MIXER TRANSITION` mode:
+`mixer_profile` 1 will be used as default, `mixer_profile` 2 will be used when the `MIXER PROFILE 2` mode box is activated. 
+Set `MIXER TRANSITION` accordingly when you want to use `MIXER TRANSITION` input for motors and servos. Here is sample of using these RC modes:
 
 ![Alt text](Screenshots/mixer_profile.png)
 
@@ -116,29 +64,50 @@ Set `MIXER TRANSITION` accordingly when you want to use `MIXER TRANSITION` input
 
 It is also possible to set it as 4 state switch by adding FW(profile1) with transition on.
 
-### Automated Transition
+## Automated Transition
 This feature is mainly for RTH in a failsafe event. When set properly, model will use the FW mode to fly home efficiently, And land in the MC mode for easier landing.
-Set `mixer_automated_switch` to `ON` in mixer_profile for MC mode. Set `mixer_switch_trans_timer` in mixer_profile for MC mode for the time required to gain airspeed for your model before entering to FW mode, for example, 50 ds. Finally set `mixer_automated_switch` to `ON` in mixer_profile for FW mode to let the model land in MC mode.
-```
-mixer_profile 2
-set mixer_automated_switch = ON
-set mixer_switch_trans_timer = 50
-mixer_profile 1
-set mixer_automated_switch = ON
-save
-```
-
 `ON` for a mixer_profile\`s `mixer_automated_switch` means to schedule a Automated Transition when RTH head home(applies for MC mixer_profile) or RTH Land(applies for FW mixer_profile) is requested by navigation controller.
-
+Set `mixer_automated_switch` to `ON` in mixer_profile for MC mode. Set `mixer_switch_trans_timer` in mixer_profile for MC mode for the time required to gain airspeed for your model before entering to FW mode.
 When `mixer_automated_switch`:`OFF` is set for all mixer_profiles(defaults). Model will not perform automated transition at all.
 
+## TailSitter (planned for INAV 7.1)
+TailSitter is supported by add a 90deg offset to the board alignment. Set the board aliment normally in the mixer_profile for FW mode(`set platform_type = AIRPLANE`), The motor trust axis should be same direction as the airplane nose. Then, in the mixer_profile for takeoff and landing set `tailsitter_orientation_offset = ON ` to apply orientation offset. orientation offset will also add a 45deg orientation offset.
+
+## Parameter list (Partial List)
+####  Please be aware of what parameter is shared among FW/MC modes and what isn't. 
+### Shared Parameters
+
+- **Timer Overrides**
+- **Outputs [Servo]:**
+  - Servo min-point, mid-point, max-point settings
+- **Motor Configuration:**
+  - motor_pwm_protocol
+  - motor_poles
+- **Servo Configuration:**
+  - servo_protocol
+  - servo_pwm_rate
+- **Board Alignment**
+- ·······
+### Profile-Specific Parameters in VTOL
+- **Mixer Profile**
+    - **Mixer Configuration:**
+        - platform_type
+        - motor_stop_on_low
+        - tailsitter_orientation_offset
+        - motor_direction_inverted, and more·······
+    - **Motor Mixing (mmix)**
+    - **Servo Mixing (smix)**
+- **PID Profile**
+  - PIDs for Roll, Pitch, Yaw
+  - PIDs for Navigation Modes
+  - TPA (Throttle PID Attenuation) Settings
+  - Rate Settings
+  - ·······
 
 ## Happy flying
 
 Remember that this is currently an emerging capability:
 
 * Test every thing on bench first.
-* Remove the props and try `MIXER PROFILE 2`, `MIXER TRANSITION` RC modes while arming.
-* Then try MR or FW mode separately see if there are any problems.
-* Try it somewhere you can recover your model in case of fail-safe. Fail-safe behavior is unknown at the current stage of development.
+* Try MR or FW mode separately see if there are any problems.
 * Use the INAV Discord for help and setup questions; use the Github Issues for reporting bugs and unexpected behaviors. For reporting on Github, a CLI `diff all`, a DVR and a Blackbox log of the incident will assist investigation.