-
Notifications
You must be signed in to change notification settings - Fork 1.1k
/
dw1000_arduino.xml
43 lines (40 loc) · 2.73 KB
/
dw1000_arduino.xml
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
<!DOCTYPE module SYSTEM "module.dtd">
<module name="dw1000_arduino" dir="decawave">
<doc>
<description>
Driver to get ranging data from Decawave DW1000 modules connected to Arduino
Decawave DW1000 modules (http://www.decawave.com/products/dwm1000-module) are Ultra-Wide-Band devices that can be used for communication and ranging.
Especially, using 3 modules as anchors can provide data for a localization system based on trilateration.
The DW1000 is using a SPI connection, but an arduino-compatible board can be used with the library https://github.com/thotro/arduino-dw1000 to hyde the low level drivers and provide direct ranging informations.
</description>
<configure name="DW1000_ARDUINO_UART" value="UARTX" description="UART on which arduino and its DW1000 module is connected"/>
<configure name="DW1000_ARDUINO_BAUD" value="B115200" description="UART Baudrate, default to 115200"/>
<section name="DW1000" prefix="DW1000_">
<define name="ANCHORS_IDS" value="1, 2, 3" type="int[]" description="Comma separated list of anchors ID"/>
<define name="ANCHORS_POS_X" value="0., 0., 5." type="float[]" description="Comma separated list of anchors ID over X axis"/>
<define name="ANCHORS_POS_Y" value="0., 5., 0." type="float[]" description="Comma separated list of anchors ID over Y axis"/>
<define name="ANCHORS_POS_Z" value="0., 0., 0." type="float[]" description="Comma separated list of anchors ID over Z axis"/>
<define name="OFFSET" value="0., 0., 0." type="float[]" description="Position offset other X, Y and Z axis"/>
<define name="SCALE" value="1., 1., 1." type="float[]" description="Position scale factor other X, Y and Z axis"/>
<define name="INITIAL_HEADING" value="0." description="Initial heading correction between anchors frame and global frame"/>
<define name="NB_ANCHORS" value="3" description="Set number of anchors, only 3 are required/supported at the moment"/>
</section>
</doc>
<header>
<file name="dw1000_arduino.h"/>
</header>
<init fun="dw1000_arduino_init()"/>
<periodic fun="dw1000_arduino_periodic()" freq="10"/>
<periodic fun="dw1000_arduino_report()" freq="10" autorun="FALSE"/>
<periodic fun="dw1000_reset_heading_ref()" freq="1" autorun="FALSE"/>
<event fun="dw1000_arduino_event()"/>
<makefile>
<configure name="DW1000_ARDUINO_UART" case="upper|lower"/>
<configure name="DW1000_ARDUINO_BAUD" default="B115200"/>
<file name="dw1000_arduino.c"/>
<file name="trilateration.c"/>
<define name="USE_$(DW1000_ARDUINO_UART_UPPER)"/>
<define name="DW1000_ARDUINO_DEV" value="$(DW1000_ARDUINO_UART_LOWER)"/>
<define name="$(DW1000_ARDUINO_UART_UPPER)_BAUD" value="$(DW1000_ARDUINO_BAUD)"/>
</makefile>
</module>