-
Notifications
You must be signed in to change notification settings - Fork 100
New issue
Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.
By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.
Already on GitHub? Sign in to your account
Can't change speed to knots #45
Comments
Have you already tried to do the same thing without the mod? |
@FabioMike06 I tried this with/without the mod on 1.9.3 didn't switch during descent. Once in mach, it cannot be changed. |
@nobodyn0se At this point I think it's most likely an asobo bug. I don't know if it can be fixed by SaltySimulation. |
Might be, I've been unable to figure out what's causing the issue in the code. |
Ok because I remember it being a problem on the default a320 and the a32x mod but then they fixed it on the a32x. Don't know what they did though |
flybywiresim/aircraft#739 This? Not sure by the way |
@bscout9956 the PR you mentioned only enables the toggle on ground. Above crossover altitude, the A32NX and B748 currently requires manual switch from SPD to MACH and vice versa below crossover altitude. The problem lies with vanilla code. The variable XMLVAR_AirspeedIsInMach correctly shows a value of 1 above crossover, in Autopilot_Subtemplates.xml there is some code dedicated to this switch. |
The switches I demonstrated in the pictures to change Mach to IAS and vice versa work perfectly fine at altitude. Unlike Asobo, I actually test things before I put them out for consumption.
From: nobodyn0se [mailto:notifications@github.com]
Sent: Friday, October 23, 2020 1:40 PM
To: saltysimulations/salty-747 <salty-747@noreply.github.com>
Cc: DesertRick13 <Ricardoescondido@hotmail.com>; Comment <comment@noreply.github.com>
Subject: Re: [saltysimulations/salty-747] Can't change speed to knots (#45)
@bscout9956<https://github.com/bscout9956> the PR you mentioned only enables the toggle on ground. Above crossover altitude, the A32NX and B748 currently requires manual switch from SPD to MACH and vice versa below crossover altitude. The problem lies with vanilla code. The variable XMLVAR_AirspeedIsInMach correctly shows a value of 1 above crossover, in Autopilot_Subtemplates.xml there is some code dedicated to this switch.
—
You are receiving this because you commented.
Reply to this email directly, view it on GitHub<#45 (comment)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/AROXLEVXRUORQN7BXI4AGFLSMHS3RANCNFSM4R555URQ>.
|
See attached
From: nobodyn0se [mailto:notifications@github.com]
Sent: Friday, October 23, 2020 1:40 PM
To: saltysimulations/salty-747 <salty-747@noreply.github.com>
Cc: DesertRick13 <Ricardoescondido@hotmail.com>; Comment <comment@noreply.github.com>
Subject: Re: [saltysimulations/salty-747] Can't change speed to knots (#45)
@bscout9956<https://github.com/bscout9956> the PR you mentioned only enables the toggle on ground. Above crossover altitude, the A32NX and B748 currently requires manual switch from SPD to MACH and vice versa below crossover altitude. The problem lies with vanilla code. The variable XMLVAR_AirspeedIsInMach correctly shows a value of 1 above crossover, in Autopilot_Subtemplates.xml there is some code dedicated to this switch.
—
You are receiving this because you commented.
Reply to this email directly, view it on GitHub<#45 (comment)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/AROXLEVXRUORQN7BXI4AGFLSMHS3RANCNFSM4R555URQ>.
|
After skipping (The travel to function) to decent the speed is in mach and when i click the change button nothing happens. I remember this was a problem in the A32X mod as well but they fixed.
The text was updated successfully, but these errors were encountered: