A Waveshare 4.2in display and a BME280 sensor are connected to a Raspberry Pi.
The display is used to show the following:
The current day and date, current time, exchange rate (GBP to TWD), Google
Calendar entries for the current and following days, temperature,
humidity and barometric pressure as measured by the BME280.

The display is painfully slow to update so time is only shown as hours and
minutes.

The readings are scheduled as follows:
BME280 readings every minute as time changes
Calendar every 30 minutes
Currency conversion every hour


  
  == Development Environment ==
  * OS: Raspbian for Raspberry Pi
  * Libraries required: 
        SPI library of Python
        PIL (Python Imaging Library) library

  == Raspberry Pi GPIO Pin map ==
 +-----+-----+---------+------+---+---Pi 3---+---+------+---------+-----+-----+
 | BCM | wPi |   Name  | Mode | V | Physical | V | Mode | Name    | wPi | BCM |
 +-----+-----+---------+------+---+----++----+---+------+---------+-----+-----+
 |     |     |    3.3v |      |   |  1 || 2  |   |      | 5v      |     |     |
 |   2 |   8 |   SDA.1 |   IN | 1 |  3 || 4  |   |      | 5v      |     |     |
 |   3 |   9 |   SCL.1 |   IN | 1 |  5 || 6  |   |      | 0v      |     |     |
 |   4 |   7 | GPIO. 7 |   IN | 1 |  7 || 8  | 1 | ALT5 | TxD     | 15  | 14  |
 |     |     |      0v |      |   |  9 || 10 | 1 | ALT5 | RxD     | 16  | 15  |
 |  17 |   0 | GPIO. 0 |   IN | 0 | 11 || 12 | 0 | IN   | GPIO. 1 | 1   | 18  |
 |  27 |   2 | GPIO. 2 |   IN | 0 | 13 || 14 |   |      | 0v      |     |     |
 |  22 |   3 | GPIO. 3 |   IN | 0 | 15 || 16 | 0 | IN   | GPIO. 4 | 4   | 23  |
 |     |     |    3.3v |      |   | 17 || 18 | 0 | IN   | GPIO. 5 | 5   | 24  |
 |  10 |  12 |    MOSI | ALT0 | 0 | 19 || 20 |   |      | 0v      |     |     |
 |   9 |  13 |    MISO | ALT0 | 0 | 21 || 22 | 0 | IN   | GPIO. 6 | 6   | 25  |
 |  11 |  14 |    SCLK | ALT0 | 0 | 23 || 24 | 1 | OUT  | CE0     | 10  | 8   |
 |     |     |      0v |      |   | 25 || 26 | 1 | OUT  | CE1     | 11  | 7   |
 |   0 |  30 |   SDA.0 |   IN | 1 | 27 || 28 | 1 | IN   | SCL.0   | 31  | 1   |
 |   5 |  21 | GPIO.21 |   IN | 1 | 29 || 30 |   |      | 0v      |     |     |
 |   6 |  22 | GPIO.22 |   IN | 1 | 31 || 32 | 0 | IN   | GPIO.26 | 26  | 12  |
 |  13 |  23 | GPIO.23 |   IN | 0 | 33 || 34 |   |      | 0v      |     |     |
 |  19 |  24 | GPIO.24 |  OUT | 1 | 35 || 36 | 1 | OUT  | GPIO.27 | 27  | 16  |
 |  26 |  25 | GPIO.25 |   IN | 0 | 37 || 38 | 0 | IN   | GPIO.28 | 28  | 20  |
 |     |     |      0v |      |   | 39 || 40 | 0 | IN   | GPIO.29 | 29  | 21  |
 +-----+-----+---------+------+---+----++----+---+------+---------+-----+-----+
 | BCM | wPi |   Name  | Mode | V | Physical | V | Mode | Name    | wPi | BCM |
 +-----+-----+---------+------+---+---Pi 3---+---+------+---------+-----+-----+

  == Hardware connection ==
    EPD    =>    Raspberry Pi
  * VCC    ->    3.3
  * GND    ->    GND
  * DIN    ->    MOSI
  * CLK    ->    SCLK
  * CS     ->    24 (Physical, BCM: CE0, 8)
  * D/C    ->    22 (Physical, BCM: 25)
  * RES    ->    11 (Physical, BCM: 17)
  * BUSY   ->    18 (Physical, BCM: 24)
  
    BME280 =>    Raspberry Pi
  * VIN    ->    17
  * GND    ->    9
  * SCL    ->    5
  * SDA    ->    3
  
    == How to use ==
    1, run with: 
        sudo python myPython.py
    # if use python3:
        sudo python3 myPython.py
    2, run in background
        chmod +x myPython.py
        nohup ~/Documents/Python-Projects/epaper/myPython.py