Open Datasheet Errata #19

Open
technobly opened this Issue May 4, 2015 · 24 comments

Projects

None yet

3 participants

@technobly
Member
technobly commented May 4, 2015 edited

Datasheet errata will be added to this issue when found. Datasheets will be updated with the listed version after items are checked off. Some errata may persist between revisions, and they will be moved up to the next proposed revision.

P1 Datasheet (v007)

Low Priority Items

  • Replace STM32 pin names with Particle/Wiring API names to keep everything intuitive and high level. Leave STM32 pin numbers for deep dives. #545
  • Make Image of P1 Block Diagram Snazzy
  • Change name of Spark.lbr to Particle.lbr in photon repo
  • CAN bus pins should be noted as 3.3V tolerant (technically they are 5V tolerant on the RX but since you wouldn't operate them with a 5V transceiver it's proper to classify them as 3.3V)
  • Fix and clarify pin descriptions #399 (make sure to review P1 and Photon datasheets as well)
  • Add note to clarify why MICRO_SPI1_SS is not hooked up to DAC/A6 (PA4) #469
  • Add new spare pin P1S6 to pinout, PWM list, pin description, update TESTMODE description, etc.. spark/firmware#1120 Branch added here: https://github.com/spark/docs/tree/feature/p1-datasheet-v007/p1s6
  • update DCT Layout https://docs.particle.io/datasheets/p1-datasheet/#dct-layout notably adding radio_flags, and any other new sections.

Photon Datasheet (v015)

  • Add power pin limits. #556
  • Replace STM32 pin names with Particle/Wiring API names to keep everything intuitive and high level. Leave STM32 pin numbers for deep dives. #545
  • Memory Map: Rename device_id to device_code and add device_id to DCT layout
  • CAN bus pins should be noted as 3.3V tolerant (technically they are 5V tolerant on the RX but since you wouldn't operate them with a 5V transceiver it's proper to classify them as 3.3V)
  • Fix and clarify pin descriptions #399 (make sure to review P1 and Photon datasheets as well)
  • update DCT Layout https://docs.particle.io/datasheets/photon-datasheet/#dct-layout notably adding radio_flags, and any other new sections.
  • Add warning about powering the Photon from long wires on USB and VIN, and give advice on what components can be added externally to mitigate this. From Richtek datasheet:

When a ceramic capacitor is used at the input and the power is supplied by a wall adapter through long wires, a load step at the output can induce ringing at the input, VIN. At best, this ringing can couple to the output and be mistaken as loop instability. At worst, a sudden inrush of current through the long wires can potentially cause a voltage spike at VIN large enough to damage the part

Electron Datasheet (v005)

  • Replace STM32 pin names with Particle/Wiring API names to keep everything intuitive and high level. Leave STM32 pin numbers for deep dives. #545
  • How to power the Electron without a battery.
  • Describe the usage of the VBAT to 3V3 bridge on the bottom. Update link to instructions for removing VBAT to 3V3 jumper located here: https://docs.particle.io/datasheets/electron-datasheet/#pin-markings- and here are some rough draft instructions: https://community.particle.io/t/electron-power-leak-from-vbat/21312/5
  • Electron Charging LED: But what is the "appropriate firmware command"? #326
  • Change Vin and Iin parameters to Vvin and Ivin to be more clear
  • EEPROM emulation bank 2 (64 KB) - remove only 16k used
  • v002 of the Pinout PDF has an error in the lower left of the Legend, UART4 and UART5 should be Serial4 and Serial5, not Serial2 and Serial3.
  • CAN bus pins should be noted as 3.3V tolerant (technically they are 5V tolerant on the RX but since you wouldn't operate them with a 5V transceiver it's proper to classify them as 3.3V)
  • Memory Map: for v0.6.0-rc.1 and later has 3 system parts and re-ordering (1,2,3 is now 2,1,3).
  • update DCD Layout https://docs.particle.io/datasheets/electron-datasheet/#dcd-layout notably adding radio_flags, and any other new sections.

Electron Datasheet (v004)

  • Replace some copy/paste errors in STM32 part number in Electron datasheet copied from Photon datasheet. Replace all STM32F205RGY6 with STM32F205RGT6.
  • Add full STM32F205RGT6 part number to every mention of STM32 in datasheet.

Photon Datasheet (v014)

  • Updated list of Mating Connectors

Electron Datasheet (v003)

  • Fix and clarify pin descriptions #399 (make sure to review P1 and Photon datasheets as well)
  • ERROR in Operating Current (Cellular OFF) IINavg 2-15mA, it should be IINavg 47-50mA
  • Updated list of Mating Connectors

P1 Datasheet (v006)

  • Update P1 pin listing: TESTMODE pin 33 (PA8), connected to MCO1 by default, outputs 32kHz clock for WICED powersave mode - currently unsupported for user control.

Electron Datasheet (v002)

  • Add size of Electron SIM card Nano (4FF) to all places in where SIM is referenced in the datasheet. Also include a link to a comparison of sizes.
  • Add memory map to datasheet, high level DCD view with link to the API for DCD: (use #82 as reference as well)
  • Add explanation of power inputs/outputs (PMIC/USB/VIN/Li+/3V3/3V8), and add this warning: It is not recommended to feed the Electron's 3V3 node with an external 3.3V source. Only use this 3V3 pin as an output for supporting circuitry.
  • Add DAC output limits: min resistive load is 5k ohms, and max capacitive load is 50pF.
  • SWD pin locations
  • Pinout diagram could use clarification, see #310
  • Rework block diagram to remove the dot-junction for VUSB and STM32F205, they are not connected. Only the two data lines are connected. https://docs.particle.io/datasheets/electron-datasheet/#block-diagram
  • Clean-up Recommended Operating Conditions Table #325

Photon Datasheet (v013)

  • Update Block Diagram to show VBAT broken out separately from the 3.3V supply https://docs.particle.io/datasheets/photon-datasheet/#block-diagram
  • Add full STM32F205RGY6 part number to the datasheet.
  • Change Vin and Iin parameters to Vvin and Ivin to be more clear
  • Update BT COEX section with link to example of how to control as GPIO, or add a note as note supported.Remove reference to using BT COEX pins as GPIO, this is not currently practical.
  • Add memory map to datasheet, high level DCD view with link to the API for DCD: #82
  • Add max source/sink current for I/Os, and total (each I/O is 25mA and total is 120mA)
  • Add SWD mode hookups to the JTAG info: https://community.particle.io/t/connections-for-st-link-v2-mini-jtag/16659
  • "Typical current consumption is 80mA with a 3.3V input. Deep sleep quiescent current is 160uA. " OLD INFO (SEE recommended operating conditions instead)
  • Add a section for test points, and point out where in the datasheet they are referenced. #223
  • Add known errata link that points back to this issue, which will be updated in the future with new issues found in the datasheet.
  • Add DAC output limits: min resistive load is 5k ohms, and max capacitive load is 50pF.
  • clarified note about routing signals under the Photon's antenna

P1 Datasheet (v005)

  • Pinout image 3, RESET button pin is 34 (MICRO_RST_N), not 26.
  • Add full STM32F205RGY6 part number to the datasheet.
  • Update BT COEX section with link to example of how to control as GPIO, or add a note as note supported.Remove reference to using BT COEX pins as GPIO, this is not currently practical.
  • Add memory map to datasheet, high level DCT view with link to the API for DCT: #82
  • Add max source/sink current for I/Os, and total (each I/O is 25mA and total is 120mA)
  • Add SWD mode hookups to the JTAG info: https://community.particle.io/t/connections-for-st-link-v2-mini-jtag/16659
  • Add note about 5V @ VIN for P1, this is in reference to when the SMPS shown in the Reference Design is implemented and current is measured from the VIN node shown on the schematic: https://docs.particle.io/datasheets/p1-datasheet/#recommended-operating-conditions-i-class-icon-check-i-
  • "Typical current consumption is 80mA with a 3.3V input. Deep sleep quiescent current is 160uA. " OLD INFO (SEE recommended operating conditions instead)
  • Add known errata link that points back to this issue, which will be updated in the future with new issues found in the datasheet.
  • Change all references to "Spare1-6" to "P1S0" - "P1S5"
  • Add dimension info for TAPE: https://docs.particle.io/datasheets/-datasheet/#tape-and-reel-info
  • Add DAC output limits: min resistive load is 5k ohms, and max capacitive load is 50pF.
  • clarified note about routing signals under the P1's antenna

Photon Datasheet (v012)

  • Added some information for TELEC certification stuff

Photon Datasheet (v011)

  • Add FCC IC CE Warnings and End Product Labeling Requirements, Update power output
  • Minor fix to section 3.2: A0A9 should be A0A7. Description is correct.
  • Section 3.2: Mention of A5 should be A3. Also call out DAC1 as A6. Can also be used as A3, and A6 in software.
  • Add extra pin numbers to the land pattern (25 - 31) and ref. to section 3 of the datasheet.
  • Fix RGB led part number on BOM: https://community.particle.io/t/photon-rgb-led-bom-and-footprint-dont-match/12973

Photon Datasheet (v010)

  • Update VBAT info.

Photon Datasheet (v009)

  • Remove RX and TX as ADCs.
  • Add DAC as an ADC channel 4 to the pinout diagrams and text.
  • DAC1 and DAC2 are both 12-bit, not 10-bit.
  • Fix height dimensions:
    Should be:
    With 1.44 x 0.8 x 0.27 (36.58 x 20.32 x 6.86) 5 grams
    Without 1.44 x 0.8 x 0.17 (36.58 x 20.32 x 4.32) 3.7 grams
  • Update quiescent current (80uA typical, 100uA max)

Photon Datasheet (v008)

  • Replace "Spark" with "Particle"
  • Add lead-free logo
  • Add Ordering information section (just points to store)
  • Add FCC ID, IC ID and FCC and CE logos
  • Replace the packaging image with a better quality one

PØ Datasheet (v002) - Not Released Yet

  • Image of PØ with pin numbers
  • Image of PØ with dimensions
  • Image of PØ module dimensions
  • Image of PØ module land pattern (and solder mask size)
  • Image of PØ Tape with Dimensions, Orientation and Feed Direction
  • Images of Reference Design Schematic
  • Images of Reference Design PCB
  • Image of colorful pinouts (use Photon's)
  • Image of Power Connections
  • Image of PØ module (vector) for cover page.
  • Image of PØ Block Diagram
  • Replace "Spark" with "Particle"
  • Change github.com/spark to github.com/particleio
  • Change Spark.lbr to Particle.lbr
  • Text for all sections

P1 Datasheet (v004)

  • Pin number 54 is used twice in pin mapping table. A0 / GPIO14 is pin 50 and not 54
  • Fold in any corrections made to Photon Datasheet.
  • Evaluation of this report:
  • JTAG: The schematic shows the Photon instead of the P1. Also, I was wondering if I need to breakout the Broadcom JTAG pins as well.
  • 2.6 External Coexistence Interface: I guess this text is from the Photon. I don't have a P1 in-hand yet so I can only guess based on pictures but aren't the coexistence signals routed to regular pads on the bottom of the module, unlike yours on the Photon? Accordingly, the table should show the P1 pin numbers as 57, 56, 58.
  • 3.2 Pin Description (DAC): I think DAC2 is A3 instead of A5.

P1 Datasheet (v003)

  • Update VBAT_MICRO info

P1 Datasheet (v002)

  • Image of P1 with pin numbers
  • Image of P1 with dimensions
  • Image of P1 module dimensions
  • Image of P1 module land pattern (and solder mask size)
  • Image of P1 Tape with Dimensions, Orientation and Feed Direction
  • Images of Reference Design Schematic
  • Image of colorful pinouts (use Photon's, add extra pins)
  • Image of Power Connections
  • Image of P1 module (vector) for cover page.
  • Replace "Spark" with "Particle"
  • Text for all sections

Community Updates

Update these threads when P1, PØ datasheets are released.

@technobly technobly self-assigned this May 4, 2015
This was referenced Jul 11, 2015
@technobly technobly changed the title from Datasheets to Open Datasheet Errata Feb 15, 2016
@technobly
Member

When I edit the main post such as right now, I will add a new comment here for visibility. I'm also updating all datasheets to point back to this known errata today.

@technobly
Member

Just changed this info in the P1 Datasheet Errata (SETUP -> RESET).

From:

Pinout image 3, SETUP button pin is 34 (MICRO_RST_N), not 26.

To:

Pinout image 3, RESET button pin is 34 (MICRO_RST_N), not 26.
@technobly
Member

Add electrical specification note for Photon/P1/Electron:

DAC output limits: min resistive load is 5k ohms, and max capacitive load is 50pF.
@kennethlimcp
Contributor

Electron - pinout pdf needs clarification - #310

@technobly
Member

Electron Datasheet Block Diagram error.

Rework block diagram to remove the dot-junction for VUSB and STM32F205, they are not connected. Only the two data lines are connected. https://docs.particle.io/datasheets/electron-datasheet/#block-diagram

@technobly
Member

Changed requirement for update to BT COEX pins section:

Update BT COEX section with link to example of how to control as GPIO, or add a note as note supported. Remove reference to using BT COEX pins as GPIO, this is not currently practical.

This was referenced Apr 11, 2016
@technobly
Member

Added an Electron Datasheet v003 list (some carried over from v002)

  • How to power the Electron without a battery.
  • Describe the usage of the VBAT to 3V3 bridge on the bottom
  • Electron Charging LED: But what is the "appropriate firmware command"? #326
  • Change Vin and Iin parameters to Vvin and Ivin to be more clear
@technobly
Member

Added more info to:

  • Describe the usage of the VBAT to 3V3 bridge on the bottom.
@technobly
Member

Added to the Electron Datasheet v003 list:

  • Fix and clarify pin descriptions #399 (make sure to review P1 and Photon datasheets as well)
@monkbroc
Member
monkbroc commented Jun 3, 2016

Added to Electron Datasheet list: all 64kb of EEPROM page 2 is used

@monkbroc
Member

Added to Photon datasheet: rename device_id to device_code in DCT and add device_id

@technobly
Member

Added to the Electron Datasheet v003 list:

  • v002 of the Pinout PDF has an error in the lower left of the Legend, UART4 and UART5 should be Serial4 and Serial5, not Serial2 and Serial3.
@technobly
Member

P1 Datasheet (v006) - released... other pending P1 changes slated for v007 now.

  • Update P1 pin listing: TESTMODE pin 33 (PA8), connected to MCO1 by default, outputs 32kHz clock for WICED powersave mode - currently unsupported for user control.
@technobly
Member

Added to:

P1 Datasheet (v007)

  • CAN bus pins should be noted as 3.3V tolerant (technically they are 5V tolerant on the RX but since you wouldn't operate them with a 5V transceiver it's proper to classify them as 3.3V)

Photon Datasheet (v014)

  • CAN bus pins should be noted as 3.3V tolerant (technically they are 5V tolerant on the RX but since you wouldn't operate them with a 5V transceiver it's proper to classify them as 3.3V)

Electron Datasheet (v003)

  • CAN bus pins should be noted as 3.3V tolerant (technically they are 5V tolerant on the RX but since you wouldn't operate them with a 5V transceiver it's proper to classify them as 3.3V)
  • Memory Map: for v0.6.0-rc.1 and later has 3 system parts and re-ordering (1,2,3 is now 2,1,3).
@technobly
Member

Added to Photon Datasheet (v014)

  • Add warning about powering the Photon from long wires on USB and VIN, and give advice on what components can be added externally to mitigate this. From Richtek datasheet:

When a ceramic capacitor is used at the input and the power is supplied by a wall adapter through long wires, a load step at the output can induce ringing at the input, VIN. At best, this ringing can couple to the output and be mistaken as loop instability. At worst, a sudden inrush of current through the long wires can potentially cause a voltage spike at VIN large enough to damage the part

@technobly
Member

Added to Electron Datasheet (v003)

  • ERROR in Operating Current (Cellular OFF) IINavg 2-15mA, it should be IINavg 47-50mA
@technobly
Member
technobly commented Sep 12, 2016 edited

Pulled two changes into a separate release (v003), the rest are going into (v004):

Electron Datasheet (v003)

  • Fix and clarify pin descriptions #399 (make sure to review P1 and Photon datasheets as well)
  • ERROR in Operating Current (Cellular OFF) IINavg 2-15mA, it should be IINavg 47-50mA
@technobly
Member

Electron Datasheet v003 has been released :)
https://docs.particle.io/datasheets/electron-datasheet/

@technobly
Member

Photon Datasheet (v014)

  • Updated list of Mating Connectors

Electron Datasheet (v003)

  • Updated list of Mating Connectors

and released!

@technobly
Member

Added item for P1 Datasheet v007 changes:

  • Add note to clarify why MICRO_SPI1_SS is not hooked up to DAC/A6 (PA4) #469
@technobly
Member
technobly commented Sep 19, 2016 edited

Added items for P1 Datasheet v007:

Added item for Photon Datasheet v015:

Added item for Electron Datasheet v004:

@technobly
Member

Bumped Electron Datasheet (v004) changes to (v005)

Added:

Electron Datasheet (v004)

  • Replace some copy/paste errors in STM32 part number in Electron datasheet copied from Photon datasheet. Replace all STM32F205RGY6 with STM32F205RGT6.
  • Add full STM32F205RGT6 part number to every mention of STM32 in datasheet.
@technobly
Member

Electron Datasheet (v004) Released!

https://docs.particle.io/datasheets/electron-datasheet/

@technobly
Member

Added todo item for all datasheets:

  • Replace STM32 pin names with Particle/Wiring API names to keep everything intuitive and high level. Leave STM32 pin numbers for deep dives. #545
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment