Skip to content

timdawg/Deeper-Tought-2

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

10 Commits
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

#Deeper Thought 2 A program that blinks the LEDs on the PiDP-8 kit created by Oscar Vermeulen. This program is C++ and does not run in the PDP-8 simulator. The default mode is designed to be similar to Steve Gibson's Deep Thought program for the PDP-8.

Deeper Thought 2 is a fork of Deeper Thought by Norman Davie. The file gpio.c and gpio.h were copied from Oscar Vermeulen's PDP-8/simH project.

Deeper Thought 2 Demo Video on YouTube

#####Added modes by changing the 3 far left brown switches (0=down / 1=up)

  • 111 = Normal mode with all LEDs flashing (Default / Undefined fallback)
  • 011 = Sleep Mode (All LEDs off except for the columns on the right side of the panel)
  • 101 = Dim Mode - Fewer LEDs Blink (Only the Program Counter, Memory Address and Memory Buffer groups)
  • 110 = Binary Clock (From top to bottom: Hour, Minute, Second, Month, Day)
  • 001 = Snake Mode (3 LEDs move across a row then down to the next row in the opposite direction)
  • 000 = Test Mode (All LEDs on steady, except some of the columns of LEDs on the right blink off for 20ms)
  • 010 = {Spare}
  • 100 = {Spare}

#####Expanded the timing switches from 6 to 12 switches

  • The third brown and third white switch groups from the left control the maximum delay (slowest speed)
    • Up = More delay (slower)
    • Down = Less delay (faster)
    • The value from the switches is multiplied by 50,000us (50ms).
  • The second brown and second white switch groups from the left control the variability of the timing
    • Up = More variability
    • Down = Less variability (all down results in steady timing)
    • The varied amount is subtracted from the max delay, making the LEDs change faster.
  • The timing range should be the similar to version 1.0, but with more degrees of change
    • The maximum delay switch mask value has 1 added to it to prevent a delay of 0, which crashed the program.
    • The delay range (before variability) is 50ms to 3200ms

#####Changed the behavior of the LED columns on the right side of the panel

  • All LEDs in the left column blink randomly.
    • Some of these LEDs are programmed to flash more often than others (see the rand_flag function).
  • The left column of LEDs are turned off for 20ms at the end of each cycle.
    • This gives the left column a short blink even if that LED stays on in the next cycle.
    • The 20ms delay is subtracted from the main blink delay to keep the same timing.
  • Instead of toggling the execute LED, it blinks for 20ms.
    • It is turned on at the beginning of the cycle and turned off before the 20ms delay described above.

#####Changed the stop switch so that it must be held for 3 seconds to quit the program

#####Added new command sequences:

  • Shutdown system - Flip both the Sing Inst and Sing Step switches down and hold the Stop button for 3 seconds
  • Reboot system - Flip both the Sing Inst and Sing Step switches down and hold the Start button for 3 seconds

#####Misc Notes:

  • Added console output that shows switch values when the switches change.
  • The blink delay is fixed to 1/2 second in Binary Clock mode.
  • This should not be run simultaneously with the pidp8 simulator

#####Installation

  • To install run "sudo ./install_deeper.sh" in the deeper directory (also builds)
  • The install script enables auto-start and disables auto-start for the pidp8 simulator
    • To install without enabling auto-start, add the "--no-autostart" parameter
    • To later disable auto-start and restore the pidp8 simulator auto-start, add the "--restore-pidp8" parameter
  • To just build run "make" in the deeper directory.

#####Running Deeper Thought 2 (if installed with the install script)

  • Stop the pidp8 simulator before running this (sudo /etc/init.d/pidp8 stop)
  • To run as a daemon in the background:
    • sudo /etc/init.d/deeper {start|stop|restart|status}
  • To run in the terminal window run:
    • sudo /usr/bin/deeper

About

A program that blinks the LEDs on the PiDP-8 kit

Resources

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published