-
Notifications
You must be signed in to change notification settings - Fork 0
Shelly 2.5
The Shelly 2.5 is supported from Tasmota 6.5.0.8 using a template.
Do not connect AC power and the serial connection at the same time The GND connection of the Shelly has a 50% chance of being connected to the live AC wire. Connecting serial with your PC will fry your PC.
Do not connect any additional sensors to serial pins. It can at least destroy your Shelly!
Check the correct jumper position before connecting AC power to Shelly 1. If the jumper is set to 12V you will destroy your Shelly!
Warning (April 10, 2019): https://www.facebook.com/groups/ShellyIoTCommunitySupport/permalink/2029876037111750/
This appears to affect a percentage of their entire first run production. Check your device before powering it on.
An ESP8266 with 2MB flash dual relay device with Energy Monitoring. Slightly smaller than the original Shelly 2.
New Shelly 2.5 model comes with a partially exposed programming/debug header which can be used to flash Tasmota on the device. A USB-to-UART adapter is needed as well as a reliable 3.3V with at least 350 mA drive capability. The following diagram shows the device pinout and power source voltage selection jumper.
Tasmota 6.5.0.8 and up supports Shelly 2.5 using the following template:
{"NAME":"Shelly 2.5","GPIO":[56,255,17,255,21,83,0,0,6,82,5,22,156],"FLAG":2,"BASE":18}
As the Temperature sensor uses the Analog input the firmware needs to be compiled with //#define USE_ADC_VCC
.
If you connect momentary switches and want press/double press/hold functionality, use the following template:
{"NAME":"Shelly 2.5 (buttons)","GPIO":[56,255,17,255,21,127,0,0,6,128,5,22,156],"FLAG":2,"BASE":18}
Run
backlog SetOption1 1; SetOption11 1; SetOption32 1```
to enable all three states. Button1 is the button on the back of the device, Button2 and Button3 are the externally connected buttons.
## Flash mode
To be able to flash the Tasmota firmware you need to get into flash mode. Therefore connect a wire from GPIO0 to ground. For further information have a look at [bringing-the-module-in-flash-mode](https://github.com/arendst/Sonoff-Tasmota/wiki/Hardware-Preparation#bringing-the-module-in-flash-mode).
## Calibration
Tasmota will disable serial logging after a restart as the communication between Tasmota and the Energy Monitoring chip is using the same serial interface. Make sure not to enable `SerialLog` as it will interfere with the Energy Monitoring functionality.
To calibrate the Energy monitoring feature connect a known load and execute the commands shown below. Assumed an AC voltage of 240V, a resistive load of 60W and a line frequency of 50Hz. With a load of 60W the current should be 60W / 240V = 0.25A.
FrequencySet 50.000 PowerSet 60.00 VoltageSet 240.0 CurrentSet 250.0
Pause a few seconds between executing the commands as the communication between Tasmota and the Energy Monitoring chip is a serial interface which can take over a second to complete.
## Use rules to control shutter endpoints
As the Shelly 2 contains energy monitoring you can use rules to power off the shutter when too much current is drawn at the end point. The below rule will power off both directions when the current becomes more than 500mA.
rule on energy#current>0.500 do backlog power1 0; power2 0 endon rule 1 rule 5
## Ghost switching
The Shelly 2 inputs appear to bne notoriously susceptible to interference. Therefore ghost switching can happen.
You might want to experiment with the switch debounce delay. It is set to 50 milliseconds by default.
Use command `switchdebounce 100` to change it to a less sensitive value, which might work better. The value can change up to 1000 milliseconds.
Some issues were reported for this topic. You can have a look at the following search query: https://github.com/arendst/Sonoff-Tasmota/issues?utf8=%E2%9C%93&q=ghost+shelly
Home
What's New
Contributing
Installation
Prerequisites
Hardware Preparation
Flashing
Initial Configuration
MQTT
Upgrading
Troubleshooting
Tutorials
FAQ
Features
Commands
Templates
Modules
Components
Rules
Smart Home Integrations
Device Configuration
Device Templates Repository
Flashing Guides
Buttons and Switches
Sensors
Lights
Displays
Useful Topics
Power Monitoring Calibration
MQTT Overview
MQTT Retained Messages
Energy Saving
Securing Your Setup
Syslog Setup
Theo's Tips
Various Tips
LEGO Nightstand Switch
For Developers
JSON Status Responses
Sensor API
Time Proportioned Output Fork
PID Control Fork