[V3 Test] Configuration Matrix #741
Comments
|
Not just need to test , need also to setup each config - it will be a long week ... |
|
Ok My Azteeg Mini is dead - the SD card reader was unsoldered and I destroy all trying to fix it - too small for my fat toes... 😿 |
|
I would like to test more repetier e.g V2 but I currently have not supported board in hand: https://github.com/repetier/Repetier-Firmware/tree/dev2 |
|
I did not noticed the Cheetah board need a 24V power supply - which I do not have currently - I will go to buy one next week |
|
For some reason my Cheetah board is actually not functionnal so I need to switch corresponding tests to another one, also I did not put ESP32-S2 (which is mono core like C3) neither ESP32-S3 (dual core like ESP32), so will add one test for each |
|
I have ordered a MKS 3.5 to replace the damaged 3.2, and a BTT Octopus 1.1 to replace the cheetah that is not working. I still need to order BTT esp32/esp7 modules for the octopus as I saw the ESP SPI pins are connected to Octopus SPI SD so it may me a good oportunity to add direct sd upload on this board => TBC |
|
I have some delay but still doing tests - ESP32Cam is now working again as well as authentication - I am now working on embedded display which also need a refactoring |
|
Hi, I managed to install successfully ESP3D on my SKR Mini E3 v1.2 (TMC2209) board by plugging a D1 Mini straight onto the TFT headers. I did not install a TFT touchscreen display anyway, I'm fine with the stock Ender 3 screen, and everything is working perfect: I can provide the wiring diagram if needed, just let me know. Thank you! :) |
This comment was marked as off-topic.
This comment was marked as off-topic.
|
May be add this table result to esp3d.io could be a good reference to complete the hardware section |
|
each esp hardware has been added to esp3d.io and almost each printer board are described in how to connect |
|
This issue has been automatically locked since there has not been any recent activity after it was closed. Please open a new issue for related bugs. |
Here my testing configurations matrix for reference, any other hardware feel free to feedback I can add :
I will add features tested after the first test, also I have ordered some ESP32 with ESP01 form factor, I will add them in test list also when received.
ESP32-C3(ESP01 form factor)
Limitations due to MKS Marlin code
Display MKSTS35 V2.0
Boot delay to 24000 to see the IP
No issue when cold start unlike AZMZ
ESP32-C3(ESP01 form factor)
Need hard reset when doing cold start
TFT are used with Marlin Flashed boards
ESP32-C3(ESP01 form factor)
ESP32-C3(ESP01 form factor)
Detailed tests
BTT SKR PRO V1.2 / ESP01 & ESP32-C3
if enabled
if working
BTT SKR V1.3 / Panucatt WifiBackPack
if enabled
if working
MKS Robin Nano V2.0 / ESP12
custom output
custom output
* custom output
* subdir are not accessible
Ramp/Mega / Nodemcu
repetier/Repetier-Firmware#1084
AZSMZ mini 2.1 (2015) / ESP01 & ESP32-C3
no space allowed
only on SD
Re-ARM /Ramps / Panucatt WifiBackPack
no space allowed
MKS TFT70 V1.1 / MKS WiFi
custom output
BTT TFT70 V3 / ESP01 & ESP32-C3
BTT TFT35-E3 V3 / ESP01 & ESP32-C3
The text was updated successfully, but these errors were encountered: