Settings Guide

[dontfeelcold]

In the version 2.0.40 under "Settings: Grbl", there used to be text under the tick boxes explaining what the various settings did. In the current version 2.0.42, that text has disappeared.

It would be nice to have it back.

Also, each time I go between each setting, there is a lag in the page loading.

Neither problem exist in 2.0.40

[terjeio]

Which controller and version? Paste Help > About > To Clipboard in a comment.

[dontfeelcold]

version 2.0.40
%
; grblHAL
; 1.1f.20210715
; [OPT:VNMSL+,999,1024,4,0]
; [NEWOPT:ENUMS,RT+,ES,TC,ETH]
; [FIRMWARE:grblHAL]
; [NVS STORAGE:*FLASH]
; [DRIVER:iMXRT1062]
; [DRIVER VERSION:210725]
; [DRIVER OPTIONS:USB.2]
; [BOARD:T41U5XBB]
; [AUX IO:1,3,0,0]
; [NETCON:Telnet]
; [IP:192.168.5.1]
; [PLUGIN:ENCODER v0.01]
;
$N0=
$N1=
; 0 - Step pulse time
$0=10.0
; 1 - Step idle delay
$1=25
; 2 - Step pulse invert
$2=0
; 3 - Step direction invert
$3=1
; 4 - Invert step enable pin(s)
$4=0
; 5 - Invert limit pins
$5=0
; 6 - Invert probe pin
$6=0
; 7 - Disable spindle with zero speed
$7=0
; 10 - Status report options
$10=511
; 11 - Junction deviation
$11=0.010
; 12 - Arc tolerance
$12=0.002
; 13 - Report in inches
$13=0
; 14 - Invert control pins
$14=78
; 15 - Invert coolant pins
$15=0
; 16 - Invert spindle signals
$16=0
; 17 - Pullup disable control pins
$17=0
; 18 - Pullup disable limit pins
$18=0
; 19 - Pullup disable probe pin
$19=0
; 20 - Soft limits enable
$20=0
; 21 - Hard limits enable
$21=0
; 22 - Homing cycle
$22=0
; 23 - Homing direction invert
$23=0
; 24 - Homing locate feed rate
$24=25.0
; 25 - Homing search seek rate
$25=500.0
; 26 - Homing switch debounce delay
$26=250
; 27 - Homing switch pull-off distance
$27=1.000
; 28 - G73 Retract distance
$28=0.100
; 29 - Pulse delay
$29=0.0
; 30 - Maximum spindle speed
$30=1000.000
; 31 - Minimum spindle speed
$31=0.000
; 32 - Mode of operation
$32=0
; 33 - Spindle PWM frequency
$33=5000
; 34 - Spindle PWM off value
$34=0.0
; 35 - Spindle PWM min value
$35=0.0
; 36 - Spindle PWM max value
$36=100.0
; 37 - Steppers deenergize
$37=0
; 39 - Enable legacy RT commands
$39=1
; 40 - Limit jog commands
$40=0
; 41 - Parking cycle
$41=0
; 42 - Parking axis
$42=2
; 43 - Homing passes
$43=1
; 44 - Axes homing, first pass
$44=4
; 45 - Axes homing, second pass
$45=3
; 46 - Axes homing, third pass
$46=0
; 47 - Axes homing, fourth pass
$47=0
; 56 - Parking pull-out distance
$56=5.0
; 57 - Parking pull-out rate
$57=100.0
; 58 - Parking target
$58=-5.0
; 59 - Parking fast rate
$59=500.0
; 60 - Restore overrides
$60=0
; 61 - Safety door options
$61=0
; 62 - Sleep enable
$62=0
; 63 - Feed hold actions
$63=2
; 64 - Force init alarm
$64=0
; 65 - Probing feed override
$65=0
; 70 - Network Services
$70=3
; 80 - Spindle P-gain
$80=1.000
; 81 - Spindle I-gain
$81=0.010
; 82 - Spindle D-gain
$82=0.000
; 84 - Spindle PID max error
$84=0.000
; 85 - Spindle PID max I error
$85=10.000
; 90 - Spindle sync P-gain
$90=0.000
; 91 - Spindle sync I-gain
$91=0.000
; 92 - Spindle sync D-gain
$92=0.000
; 95 - Spindle sync PID max I error
$95=0.000
; 100 - X-axis travel resolution
$100=315.000
; 101 - Y-axis travel resolution
$101=250.000
; 102 - Z-axis travel resolution
$102=250.000
; 103 - A-axis travel resolution
$103=250.000
; 110 - X-axis maximum rate
$110=1000.000
; 111 - Y-axis maximum rate
$111=500.000
; 112 - Z-axis maximum rate
$112=500.000
; 113 - A-axis maximum rate
$113=500.000
; 120 - X-axis acceleration
$120=100.000
; 121 - Y-axis acceleration
$121=10.000
; 122 - Z-axis acceleration
$122=10.000
; 123 - A-axis acceleration
$123=10.000
; 130 - X-axis maximum travel
$130=200.000
; 131 - Y-axis maximum travel
$131=200.000
; 132 - Z-axis maximum travel
$132=200.000
; 133 - A-axis maximum travel
$133=200.000
; 160 - X-axis backlash compensation
$160=0.000
; 161 - Y-axis backlash compensation
$161=0.000
; 162 - Z-axis backlash compensation
$162=0.000
; 163 - A-axis backlash compensation
$163=0.000
; 300 - Hostname
$300=GRBL
; 301 - IP Mode
$301=0
; 302 - IP Address
$302=192.168.5.1
; 303 - Gateway
$303=192.168.5.1
; 304 - Netmask
$304=255.255.255.0
; 305 - Telnet port
$305=23
; 307 - Websocket port
$307=80
; 341 - Tool change mode
$341=0
; 342 - Tool change probing distance
$342=30.0
; 343 - Tool change locate feed rate
$343=25.0
; 344 - Tool change search seek rate
$344=200.0
; 345 - Tool change probe pull-off rate
$345=100.0
; 347 - Dual axis length fail
$347=5.0
; 348 - Dual axis length fail min
$348=2.500
; 349 - Dual axis length fail max
$349=25.000
; 370 - Invert I/O Port inputs
$370=0
; 372 - Invert I/O Port outputs
$372=0
; 400 - Encoder mode
$400=0
; 401 - Encoder counts per revolution
$401=400
; 402 - Encoder counts per detent
$402=4
; 403 - Encoder double click sensitivity
$403=500
%

version 2.0.42
%
; grblHAL
; 1.1f.20210715
; [OPT:VNMSL+,999,1024,4,0]
; [NEWOPT:ENUMS,RT+,ES,TC,ETH]
; [FIRMWARE:grblHAL]
; [NVS STORAGE:*FLASH]
; [DRIVER:iMXRT1062]
; [DRIVER VERSION:210725]
; [DRIVER OPTIONS:USB.2]
; [BOARD:T41U5XBB]
; [AUX IO:1,3,0,0]
; [NETCON:Telnet]
; [IP:192.168.5.1]
; [PLUGIN:ENCODER v0.01]
;
$N0=
$N1=
; 0 - Step pulse time
$0=10.0
; 1 - Step idle delay
$1=25
; 2 - Step pulse invert
$2=0
; 3 - Step direction invert
$3=1
; 4 - Invert step enable pin(s)
$4=0
; 5 - Invert limit pins
$5=0
; 6 - Invert probe pin
$6=0
; 7 - Disable spindle with zero speed
$7=0
; 10 - Status report options
$10=511
; 11 - Junction deviation
$11=0.010
; 12 - Arc tolerance
$12=0.002
; 13 - Report in inches
$13=0
; 14 - Invert control pins
$14=78
; 15 - Invert coolant pins
$15=0
; 16 - Invert spindle signals
$16=0
; 17 - Pullup disable control pins
$17=0
; 18 - Pullup disable limit pins
$18=0
; 19 - Pullup disable probe pin
$19=0
; 20 - Soft limits enable
$20=0
; 21 - Hard limits enable
$21=0
; 22 - Homing cycle
$22=0
; 23 - Homing direction invert
$23=0
; 24 - Homing locate feed rate
$24=25.0
; 25 - Homing search seek rate
$25=500.0
; 26 - Homing switch debounce delay
$26=250
; 27 - Homing switch pull-off distance
$27=1.000
; 28 - G73 Retract distance
$28=0.100
; 29 - Pulse delay
$29=0.0
; 30 - Maximum spindle speed
$30=1000.000
; 31 - Minimum spindle speed
$31=0.000
; 32 - Mode of operation
$32=0
; 33 - Spindle PWM frequency
$33=5000
; 34 - Spindle PWM off value
$34=0.0
; 35 - Spindle PWM min value
$35=0.0
; 36 - Spindle PWM max value
$36=100.0
; 37 - Steppers deenergize
$37=0
; 39 - Enable legacy RT commands
$39=1
; 40 - Limit jog commands
$40=0
; 41 - Parking cycle
$41=0
; 42 - Parking axis
$42=2
; 43 - Homing passes
$43=1
; 44 - Axes homing, first pass
$44=4
; 45 - Axes homing, second pass
$45=3
; 46 - Axes homing, third pass
$46=0
; 47 - Axes homing, fourth pass
$47=0
; 56 - Parking pull-out distance
$56=5.0
; 57 - Parking pull-out rate
$57=100.0
; 58 - Parking target
$58=-5.0
; 59 - Parking fast rate
$59=500.0
; 60 - Restore overrides
$60=0
; 61 - Safety door options
$61=0
; 62 - Sleep enable
$62=0
; 63 - Feed hold actions
$63=2
; 64 - Force init alarm
$64=0
; 65 - Probing feed override
$65=0
; 70 - Network Services
$70=3
; 80 - Spindle P-gain
$80=1.000
; 81 - Spindle I-gain
$81=0.010
; 82 - Spindle D-gain
$82=0.000
; 84 - Spindle PID max error
$84=0.000
; 85 - Spindle PID max I error
$85=10.000
; 90 - Spindle sync P-gain
$90=0.000
; 91 - Spindle sync I-gain
$91=0.000
; 92 - Spindle sync D-gain
$92=0.000
; 95 - Spindle sync PID max I error
$95=0.000
; 100 - X-axis travel resolution
$100=315.000
; 101 - Y-axis travel resolution
$101=250.000
; 102 - Z-axis travel resolution
$102=250.000
; 103 - A-axis travel resolution
$103=250.000
; 110 - X-axis maximum rate
$110=1000.000
; 111 - Y-axis maximum rate
$111=500.000
; 112 - Z-axis maximum rate
$112=500.000
; 113 - A-axis maximum rate
$113=500.000
; 120 - X-axis acceleration
$120=100.000
; 121 - Y-axis acceleration
$121=10.000
; 122 - Z-axis acceleration
$122=10.000
; 123 - A-axis acceleration
$123=10.000
; 130 - X-axis maximum travel
$130=200.000
; 131 - Y-axis maximum travel
$131=200.000
; 132 - Z-axis maximum travel
$132=200.000
; 133 - A-axis maximum travel
$133=200.000
; 160 - X-axis backlash compensation
$160=0.000
; 161 - Y-axis backlash compensation
$161=0.000
; 162 - Z-axis backlash compensation
$162=0.000
; 163 - A-axis backlash compensation
$163=0.000
; 300 - Hostname
$300=GRBL
; 301 - IP Mode
$301=0
; 302 - IP Address
$302=192.168.5.1
; 303 - Gateway
$303=192.168.5.1
; 304 - Netmask
$304=255.255.255.0
; 305 - Telnet port
$305=23
; 307 - Websocket port
$307=80
; 341 - Tool change mode
$341=0
; 342 - Tool change probing distance
$342=30.0
; 343 - Tool change locate feed rate
$343=25.0
; 344 - Tool change search seek rate
$344=200.0
; 345 - Tool change probe pull-off rate
$345=100.0
; 347 - Dual axis length fail
$347=5.0
; 348 - Dual axis length fail min
$348=2.500
; 349 - Dual axis length fail max
$349=25.000
; 370 - Invert I/O Port inputs
$370=0
; 372 - Invert I/O Port outputs
$372=0
; 400 - Encoder mode
$400=0
; 401 - Encoder counts per revolution
$401=400
; 402 - Encoder counts per detent
$402=4
; 403 - Encoder double click sensitivity
$403=500
%

[terjeio]

Ok, thats an old controller version. You are either stuck with 2.0.40 or you have to update the controller firmware. You may use the Web Builder to create a binary if you decide to update.

[dontfeelcold]

Thank you

[dontfeelcold]

Fixed