Balanced Cross Sections, Shortening Estimates, and the Magnitude of Out-of-Sequence Thrusting in the Nankai Trough Accretionary Prism, Japan
This is a repository of data and calculations for an upcoming paper. A draft of the paper is available at: http://www.geology.wisc.edu/~jkington/Kington-OOST_Paper.pdf
This work extensively references and depends on the results of another unpublished (so far) study, which is available here: http://www.geology.wisc.edu/~jkington/Kington-OuterWedgeStructure.pdf
This work was also presented at the 2013 Fall AGU Meeting. The poster is available at: http://www.geology.wisc.edu/~jkington/2013_AGU_Poster_color_coded_reduced.pdf
The 3D inclined shear method used to restore the horizons is implemented in the
fault_kinematics library: https://github.com/joferkington/fault_kinematics.
The Python scripts in this repository handle the site and project specific
calculations and visualizations.
Out-of-sequence thrusting seaward of the Kumano Basin in the Nankai Accretionary Prism, Japan has been a focus of extensive recent work and multiple IODP expeditions. However, the amount of shortening and along strike motion accommodated by the thrusts has not been studied in detail. We constrain the total amount of shortening accommodated by the out-of-sequence thrust system (OOSTS) in two ways. First, we compare the total shortening accommodated by all other structures in the outer wedge to the amount of shortening predicted by plate motions. Bed-length balancing of structures suggests that the outer wedge has accommodated 75±16 km of shortening over the last 2.3±0.2 myr, while plate motion models [Loveless & Meade, 2010] predict 99±10 km of convergence between the forearc block and the subducting Philippine Sea Plate. If we assume that all other shortening is accommodated by the out-of-sequence thrust system, this predicts 24±19 km of shortening on the OOSTS. For the second method, we use fault geometry and syn-kinematic forearc stratigraphy to model the magnitude and direction of slip on the zone’s youngest structure. Modeling growth stratigraphy within the forearc basin using inclined shear along the observed 3D fault geometry predicts 15±2 km of shortening (14±2 km dip-slip, 6±1 km right-lateral strike-slip) accommodated by the younger of the two major thrusts in the OOSTS. Additionally, the growth strata in the forearc older than ∼0.5 Ma are best fit by oblique slip along the fault at an azimuth of 321°, subparallel to plate motion. The growth strata also constrain uplift of the forearc to have begun no earlier than 0.9-1.04 Ma and to have continued until sometime more recently than ∼0.5 Ma. In contrast, Gulick, et al [2010] concluded that uplift of the forearc began at 1.24-1.34 Ma and ended by 0.9-1.04 Ma. Our constraints on the timing suggests that there was a ∼0.2-0.3 myr period between activity on older and younger thrusts in the OOSTS when shortening was primarily accommodated on structures near the toe of the accretionary prism. Furthermore, comparing the duration of activity with our estimates for the motion on each structure in the OOSTS suggests that each of the two thrusts accommodated ∼~40% of the total plate convergence during the time that they were active.
- Python 2.6 or 2.7
- Matplotlib >= 1.0
- Numpy >= 1.5
- Scipy >= 0.6
- h5py >= 2.0
- Uncertainties >= 2.0
- Python-geoprobe
- <https://github.com/joferkington/fault_kinematics>
- <https://github.com/joferkington/seismic_plotting>
Some visualizations (e.g.
interactive_inclined_shear.py) require Mayavi and Tvtk.
- shortening_calculations.py
- Calculation of shortening and error from line-length balancing and plate convergence.
- process_bootstrap_results.py
- Calculates shortening (and errors) parallel to the section line from the saved results of bootstrapping the inclined-shear restoration.
- bootstrap_error.py
- Runs a parallel monte-carlo inversion to estimate both the amount of
slip and the error in the estimate. This inverts for slip 200 times for
each horizon, using boostrapping with replacement on the points in both
the horizon and fault geometries. The results are stored in
bootstrap.hdf5. - basic.py
- A simple best-fit inversion of the amount of slip along the fault to
restore each horizon to horizontal. For the paper, the results are
obtained from
bootstrap_error.py, but this demonstrates a single, best-fit inversion.
- plot_bootstrap_results.py
- Plots slip over time with error ellipses. Generates the base for Figure 8 in the paper.
- plot_dip_development.py
- Plots present-day strike and dip of forearc stratigraphy. Generates the base for Figure 9 in the paper.
- plot_line_balancing_and_plate_motion.py
- Plots the results of the bootstrapped inclined shear restoration.
- forearc_detail_section.py
- Plots a detailed cross section through the uplifted forearc basin stratigraphy. The base plot for Figure 3 in the paper.
- error_ellipse.py
- Utilities for plotting error ellipses.
- interactive_basic.py
- An interactive 3D visualization of the results. Displays the restored position of one of the horizons and the fault geometry and lets the user simulate slip on the fault.
- interactive_inclined_shear.py
- Functions used in
interactive_basic.py. Displays the present day geometries of the fault and a horizon and lets the user simulate slip on the fault. - visualize_solution.py
- An interactive 3D visualization of of the results.
- depth_conversion_simple.py
- Builds a 1D time-depth for the fault surface beneath the forearc (and only the fault surface beneath the forearc) using the observed fault geometry in both time and depth. (We didn't have access to the velocity model for the 3D volume at the time.) This is then applied to the fault surface picked from the 2D data to convert it to depth.
- fit_shear_angle.py
- Finds the best fitting shear angle for each horizon using a grid search.
- sequential_restoration.py
- Attempt to invert for slip where the horizons are not restored
independently. This gives identical results as the independent version
(
basic.pyandbootstrap_error.py). This demonstrates that the result is not sensitive to the fact that each horizon is restored independently of the one before it.
- data.py
- Locations of datafiles and transform utilities.
- utilities.py
- Various utility functions used throughout the project.
- restore_horizons.py
- Restores horizons (same as
basic.py) and writes the restored horizons out as geoprobe horizon files. - sequential_restoration_cross_section.py
- Plots Figure 7 in the paper.
- grid_search.py
- Preforms a grid search for the best fit and displays the "roughness" of the horizon (i.e. misfit) at each point in the grid and displays the misfit surface. This demonstrates that there are few local minima, validating the choice of basic "gradient descent" inversions.