/
hwdef.dat
172 lines (134 loc) · 4.1 KB
/
hwdef.dat
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
# hw definition file for processing by chibios_pins.py
# Mamba F405 MK2
# With F405 MCU, MPU6000 IMU and 7456 series OSD
# Based on Mamba F405 from jeanphilippehell
@ thanks to betaflight for pin information
# MCU class and specific type.
MCU STM32F4xx STM32F405xx
HAL_CHIBIOS_ARCH_F405 1
# board ID for firmware load
APJ_BOARD_ID 1019
# crystal frequency
OSCILLATOR_HZ 8000000
# board voltage
STM32_VDD 330U
STM32_ST_USE_TIMER 4
define CH_CFG_ST_RESOLUTION 16
# order of I2C buses
I2C_ORDER I2C1
# order of UARTs (and USB)
# this order follows the labels on the board
# namely COMPUTER, PPM/SBUS (configurable as USART), TX3/RX3, TX6/RX6
SERIAL_ORDER OTG1 USART1 EMPTY USART3 EMPTY EMPTY USART6
# The pins that USB is connected on
PA11 OTG_FS_DM OTG1
PA12 OTG_FS_DP OTG1
PC5 VBUS INPUT OPENDRAIN
# USART1 is wired to SBUS and PPM input
# RC input defaults to timer capture
PA10 TIM1_CH3 TIM1 RCININT PULLDOWN
PA9 USART1_TX USART1
# Alt config to allow RCIN on UART
PA10 USART1_RX USART1 ALT(1)
define DEFAULT_SERIAL1_PROTOCOL SerialProtocol_RCIN
# SBUS inversion control pin, active low
PC0 USART1_RXINV OUTPUT HIGH GPIO(78) POL(0)
define DEFAULT_SERIAL2_PROTOCOL SerialProtocol_None
# USART3 (VTX)
PB10 USART3_TX USART3
PB11 USART3_RX USART3
define DEFAULT_SERIAL3_PROTOCOL SerialProtocol_Tramp
define DEFAULT_SERIAL4_PROTOCOL SerialProtocol_None
define DEFAULT_SERIAL5_PROTOCOL SerialProtocol_None
# USART6 (ESC Telemetry)
PC6 USART6_TX USART6
PC7 USART6_RX USART6
define DEFAULT_SERIAL6_PROTOCOL SerialProtocol_ESCTelemetry
# The pins for SWD debugging with a STlinkv2 or black-magic probe (not tested)
PA13 JTMS-SWDIO SWD
PA14 JTCK-SWCLK SWD
# ADC
PC1 BATT_VOLTAGE_SENS ADC1 SCALE(1)
PC2 RSSI_ADC ADC1
PC3 BATT_CURRENT_SENS ADC1 SCALE(1)
# PWM output. 1 - 4 on ESC header
PA3 TIM2_CH4 TIM2 PWM(1) GPIO(50) BIDIR
PB0 TIM3_CH3 TIM3 PWM(2) GPIO(51)
PB1 TIM3_CH4 TIM3 PWM(3) GPIO(52) BIDIR
PA2 TIM2_CH3 TIM2 PWM(4) GPIO(53)
# Board LEDs
PB5 LED_BLUE OUTPUT LOW GPIO(1)
PB4 LED_GREEN OUTPUT LOW GPIO(2)
define HAL_GPIO_A_LED_PIN 1
define HAL_GPIO_B_LED_PIN 2
# External LEDs
PA0 TIM5_CH1 TIM5 PWM(5) GPIO(54)
# Buzzer
PA8 BUZZER OUTPUT GPIO(80) LOW
define HAL_BUZZER_PIN 80
# Camera control
PB9 CAM_C OUTPUT LOW GPIO(81)
define RELAY2_PIN_DEFAULT 81
# Note that this board needs PULLUP on I2C pins
PB6 I2C1_SCL I2C1 PULLUP
PB7 I2C1_SDA I2C1 PULLUP
# SPI1 - Internal IMU
PA4 MPU6000_CS CS
PA5 SPI1_SCK SPI1
PA6 SPI1_MISO SPI1
PA7 SPI1_MOSI SPI1
# SPI2 - OSD
PB15 SPI2_MOSI SPI2
PB14 SPI2_MISO SPI2
PB13 SPI2_SCK SPI2
# OSD max7456
PB12 OSD_CS CS
# SPI3 - dataflash
PC10 SPI3_SCK SPI3
PC11 SPI3_MISO SPI3
PC12 SPI3_MOSI SPI3
# Dataflash M25P16
PB3 FLASH_CS CS
# SPI Device table
SPIDEV mpu6000 SPI1 DEVID1 MPU6000_CS MODE3 1*MHZ 4*MHZ
SPIDEV icm42688 SPI1 DEVID1 MPU6000_CS MODE3 1*MHZ 10*MHZ
SPIDEV dataflash SPI3 DEVID1 FLASH_CS MODE3 32*MHZ 32*MHZ
SPIDEV osd SPI2 DEVID4 OSD_CS MODE0 10*MHZ 10*MHZ
# One IMU rotated in yaw
IMU Invensense SPI:mpu6000 ROTATION_YAW_90
IMU Invensensev3 SPI:icm42688 ROTATION_PITCH_180
# Probe for I2C BMP280
BARO BMP280 I2C:0:0x76
define AP_BARO_BACKEND_DEFAULT_ENABLED 0
define AP_BARO_BMP280_ENABLED 1
define HAL_BARO_ALLOW_INIT_NO_BARO 1
# no built-in compass, but probe the i2c bus for all possible
# external compass types
define ALLOW_ARM_NO_COMPASS
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
define HAL_I2C_INTERNAL_MASK 0
define HAL_COMPASS_AUTO_ROT_DEFAULT 2
# enable logging to dataflash
define HAL_LOGGING_DATAFLASH_ENABLED 1
define HAL_STORAGE_SIZE 15360
STORAGE_FLASH_PAGE 1
# flash size
FLASH_SIZE_KB 1024
# reserve 32k for bootloader and 32k for flash storage
FLASH_RESERVE_START_KB 64
# define default battery setup
define HAL_BATT_VOLT_PIN 11
define HAL_BATT_CURR_PIN 13
define HAL_BATT_VOLT_SCALE 11
define HAL_BATT_CURR_SCALE 25.0
define HAL_BATT_MONITOR_DEFAULT 4
# Analog RSSI pin (also could be used as analog airspeed input)
define BOARD_RSSI_ANA_PIN 12
# Setup for OSD
define OSD_ENABLED 1
define HAL_OSD_TYPE_DEFAULT 1
# Font for the osd
ROMFS_WILDCARD libraries/AP_OSD/fonts/font*.bin
DMA_PRIORITY TIM2* TIM3*
# minimal drivers to reduce flash usage
include ../include/minimize_fpv_osd.inc