forked from ninjablocks/arduino
-
Notifications
You must be signed in to change notification settings - Fork 0
Erikle/arduino
Folders and files
Name | Name | Last commit message | Last commit date | |
---|---|---|---|---|
Repository files navigation
Ninja Blocks Arduino Source Code. Developed by www.ninjablocks.com based on Arduino and other Open Source libraries. Version 0.45: 21st December 2012 by JZ - added DID defines - added new DID 2007 for Version 1.2 board LED's Version 0.44: 8th October 2012 by JP Liew - changed RCSwitch code to ignore any data with less than 24 bits to reduce noise - removed RCSwitch::receiveProtocol2() to reduce code size - removed many functions from libraries to reduce code size - added receiveWT450() to decode WT450 raw stream - added doWT450()to decode house, station, humidity & temp from WT450 Sensor - added WT450 Humidity Device ID=30, and Temperature Device ID=31 - changed Power on status LED to BLUE Version 0.43: 2nd October 2012 by JP Liew - added TESTER code for Ninja Cape to test another fresh cape out from production - added DID 8888,8889,8890 to support special command for TESTER to send/receive signal - changed VNO to be "0.xx" for easy server parsing - added "\n" when Arduino start for a clean new line output Version 0.42: 24th August 2012 by JP Liew - added RGB Status light support - added DID 999 for V12 status RGB - added PLUGIN and UNPLUG events - changed doJSONData() to support, DEVICE, PLUGIN and UNPLUG event in one function - changed PIR and Push Button high from 1023 to 1 - changed sensor to only send on changed event, except Distance, Light and Sound - changed Light sensor to report value from 0% to 100%, in a 10 average reading Version 0.41: 20th August 2012 by JP Liew - cleaned commented codes - enabled accelerometer for V11 after testing - split do433() into GUID=0 and GUID=1 for V12 and V11 respectively Version 0.40: 20th August 2012 by JP Liew - changed doOnBoardRGB(), doOnBoardTemperature(), doDHT22() to slow down to 30 seconds per update - changed doDHT22() to continue poll data when first plugin until valid before obeying the heartbeat delay - tidied doPort1(), doPort2() and doPort3() when dealing with DHT22 - disabled DHT22 from sending -99 or 0 - disabled 433 functions from sending 0 data - changed getBoardTemperature() resolution to 1 decimal point Version 0.39: 17th August 2012 by JP Liew - added receiveLaCrosse() in RCSwitch lib to decode LaCrosse 433 Transmitter - changed RCSwitch ISR routine to be able to accept LaCrosse protocol - changed decoding to use unsigned long long for protocol longer than 32bits - added support for LaCrosse WS2355 protocol for temp, humidity, rain, wind, win direction - added support for LaCrosse TX3 protocol for temp - changed do433() in ordered to use the same routine for V11 and V12 - disabled do433() from sending -1 result Version 0.38: MAJOR code changes to accomodate V11 and V12 board, 14th August 2012 by JP Liew - added doJSONData(...) to allow easier calling of the library - clean up many precompile warnings - added V11 V12 preprocessor directives for version selection - disabled getBoardTemperature() for V12 board - disabled doOnBoardAccelerometer() for V12 board - changed doOnBoardRGB() to cater PWM for V12 board - added doOnBoard433() for V12 board Version 0.37: 30th July 2012 by JP Liew - fixed RCSwitch to add leading zeros when sending JSON data in binary - fixed GREEN LED blink on GREEN when receiving 433 data Version 0.36: 5th July 2012 by JP Liew - fixed Relay digitalWrite() not in OUTPUT mode - added Device ID 1003, DATA="VNO" for cape to report software version - disabled responding to DID 1001 with the new all in one TX & RX board - changed 433 transmit from 5 times to 8 times Version 0.35: 2nd July 2012 by JP Liew - added handling for Relay Breakout board. 2nd July 2012 - added reading ID for Relay Breakout board. 2nd July 2012 Version 0.34.1: 22th June 2012 by JP Liew - added blinkLED() for push button triggered. 22nd June 2012 Version 0.34: 15th June 2012 by JP Liew - added doOnBoardRGB() to report status of RGB Led. 15th June 2012 - added doJSONResponse() to ack server messages. 15th June 2012 - added doJSONError(int) to report error. 15th June 2012 Version 0.33: - added sound sensor support and blink RED LED if sound level exceeds 0. 1st June 2012 - fixed 433Mhz Tx & Rx interfering. 1st June 2012 - fixed readSerialString() stucked in while loop. 1st June 2012 - changed blinkGreenLED() to blinkLED() so that any LED could be blinked. 1st June 2012 Version 0.32: 31st May 2012 by JP Liew - changed TMP102 to read in 30 sec interval, reading too quickly will cause chip to heat up, thus giving slightly higher temperature reading. 30th May 2012 - added code to prevent multiple creation of ISR in enableReceive() for RCSwitch library. 31st May 2012 - added 433Mhz Rx module code. 31st May 2012 - added blinkGreenLED() when valid 433Mhz code received. 31st May 2012 Version 0.31: 29th May 2012 by JP Liew - changed JSON protocol, shorten to G,V,D,DA - fixed RGB ID bug, should be 1000 - added UNKNOWN sensor to return ADC value - added 433Mhz Tx module code - changed DHT22 humidity & temp to return float value Version 0.2: 25th May 2012 by JP Liew - restructured JSON protocol to encapsulate devices with GUID, VID, DID and DATA Version 0.1: by Marcus Schappi www.ninjablocks.com Libraries Required ================== 1. Ninja (Ninja.h header file) 2. Sensors (Ninja Blocks library) 3. NinjaObjects (Ninja Blocks library) 4. aJson 5. DHT22 6. Wire 7. I2C 8. MMA8453Q 9. RCSwitch NOTE: Please read 3rd party library's README for respective author's name and usage guide. Installation instructions ========================= 1. Extract / Check out to Arduino's libraries folder. 2. Ninja Arduino's sketch is located inside libraries --->Ninja --->NinjaArduino
About
No description, website, or topics provided.
Resources
Stars
Watchers
Forks
Packages 0
No packages published
Languages
- C++ 64.4%
- Other 16.2%
- C 9.5%
- Processing 6.8%
- Objective-C 3.1%