E3V2-UBL-BLTouch-15x15-HS-v4.2.7-v1.3.4

[MarcDuchesne001]

Hi everyone and thanks for all your hard work, we appreciate.

I am in the process to compiling my own .bin file since I have purchased an Ender 3 extender. It is basically an ender 3 that I upgraded to a V2 (4.2.7 board) with proper screen.

I have replaced the Marlin configuration.h and configuration_adv.h (UBL-BLTouch-10x10) and edited these to fit my needs for 4.2.7 board.

I am not finding info's about the HS function, if it is enables or not on these conf files.

Any help, hoping I am clear in explanations :-)

Thanks !
-marc

[MarcDuchesne001]

Just find this info. Simply enable #define BLTOUCH_HS_MODE in configuration_adv.h for high speed probing. Will take a look tonight Is this ok or more is to be setup ?

[smooreace]

I think that's all that's needed, but why not start with a config sample that better fits what you were after? (BLTouch-3x3-HighSpeed)

…

On Mon, Jun 14, 2021 at 9:09 AM MarcDuchesne001 ***@***.***> wrote: Just find this info. Simply enable #define BLTOUCH_HS_MODE in configuration_adv.h for high speed probing. Is this ok ? — You are receiving this because you are subscribed to this thread. Reply to this email directly, view it on GitHub <#1008 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AIPE4QYQYDTVLY467WH4FL3TSYESPANCNFSM46VHPXOA> .

[smooreace]

Or, you can compare the different templates in Notepad++ and see exactly what is different between them to better understand how each feature is activated

…

On Mon, Jun 14, 2021 at 9:38 AM Steve Moore ***@***.***> wrote: I think that's all that's needed, but why not start with a config sample that better fits what you were after? (BLTouch-3x3-HighSpeed) On Mon, Jun 14, 2021 at 9:09 AM MarcDuchesne001 ***@***.***> wrote: > Just find this info. Simply enable #define BLTOUCH_HS_MODE in > configuration_adv.h for high speed probing. Is this ok ? > > — > You are receiving this because you are subscribed to this thread. > Reply to this email directly, view it on GitHub > <#1008 (comment)>, > or unsubscribe > <https://github.com/notifications/unsubscribe-auth/AIPE4QYQYDTVLY467WH4FL3TSYESPANCNFSM46VHPXOA> > . >

[MarcDuchesne001]

Cool, will do and keep posted. Thanks !!!

[MarcDuchesne001]

I also modded the bed size in the conf file for 400X400 and a few other things... Since this is a larger bed, I would like more points like 10X10 or 15X15 taken.

[smooreace]

Along those lines, I just finished pushing my v2 to 400x400x500 with BL Touch and MicroSwiss DD/Hot End. I THINK I'm still printing a few MM off-center, but SOOO much room to work now!

…

On Mon, Jun 14, 2021 at 9:51 AM MarcDuchesne001 ***@***.***> wrote: I also modded the bed size in the conf file for 400X400 and a few other things... — You are receiving this because you commented. Reply to this email directly, view it on GitHub <#1008 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AIPE4QZ7RKCJY7EYBZPSR2TTSYJO5ANCNFSM46VHPXOA> .