English | 中文
This hackintosh configuration is built for the Dell XPS 9570 laptop based Clover.It theoretically supports macOS 10.14.X - macOS 10.15.X. It integrates common kexts for almost all devices,such as audio card, intel graphic card, 4K display and so on.It fully supports dual signals output using 4K@60Hz via HDMI 2.0 and Type C, thunderbolt devices are boot coldly and DW1830 is used to suppot WLAN and Airdop.It also brings original touch gestures like Mac devices, and sleep and wake up are general normal.。
- Model: Dell XPS 9570
- CPU: Intel Core i7-8750H
- Intel Graphic: UHD630
- Memory: Micron 8ATF1G64HZ-2G6E1 8GB* 2
- Display: 4K Sharp Display
- SSD: PC401 NVMe SK hynix 512GB SSD
- Trackpad: Synaptics SYNA2393
- Audio: Realtek ALC298
- Touchscreen: Wacom WCOM488F
- WLAN + Bluetooth : DW1830
- Killer 1535
- Goodix fingerpint reader
- Nvidia Geforce 1050Ti
1.5.0 - 1.11.2
- macOS Mojave:
10.14.0 - 10.14.6
- macOS Catalina:
10.15.0 - 10.15.5
This is used for installation phase, the purpose is to inject a incorrect
ig-platform-id = 0x12345678, and disable graphic card, so that the system can enter desktop after complete installation.
This file is used for
XPS 9570 8750H 4K model. The following sub-item injects the correct graphic platform and enables graphic acceleration.
- framebuffer-portcount = <04000000>
- framebuffer-con1-enable = <01000000>
- framebuffer-con1-alldata = <01050900 00040000 87010000>
- framebuffer-con2-enable = <01000000>
- framebuffer-con2-alldata = <02060900 00040000 87010000>
- framebuffer-con3-enable = <01000000>
- framebuffer-con3-alldata = <03040a00 00080000 87010000>
- enable-hdmi20 = <01000000>
- enable-lspcon-support = <01000000>
- framebuffer-con3-has-lspcon = <01000000>
- framebuffer-con3-preferred-lspcon-mode = <01000000>
It's different from
config_install.plist is that the correct
ig-platform-id = 0x3e9b0000 is injected into our system.One the other hand，the maximum link rate of the
XPS 9570 8750H 4K model is fixed by the following field:
This file is used for
XPS 9570 8750H 1080P model.The difference from
config.plist is only that:
1. Replace EFI of installation volume
Delete the clover folder from original EFI partition and replace it with the Clover folder of this repository.
2. Complete Installation
config_install.plist to enter installation UI and complete the installation; if there are installation failure problems, try multiple times to enter the installation UI.(3~5 times）
3. Rebuild kext cache
sudo kextcache -i / command in terminal to rebuild kext cache after entering desktop.
If your model is 4K, use
config.plist to enter desktop directly.Otherwise,use
5. Install some drivers into
It is recommended to only keep
CLOVE/kexts/Other, install the rest of kexts into
S/L/E. Delete all kexts in
CLOVER/kexts/other which already are installed.Finally, rebuild kext cache again and restart your computer.
config_install.plist to complete upgrade, run
sudo kextcache -i / to rebuild kext cache immediately after entering destop.
I sincerely apologize for my procrastination.But the project is stable enough and has supported full version of Catalina so far.Thank you for all passion and stars.I am strongly support everyone to promote this project. If you need to publish this EFI or reprint it to others, please be sure to indicate my repo, bavariancake's repo and Xigtun's repo.Star me if you really like my contribution for hackintosh community!