OPI gRPC to Intel SDK bridge

Download 🚀 · Report issue 🐞 · Contribute 👋

This is an Intel bridge to OPI APIs. Currently it supports storage APIs and is subject to extension for other domains including inventory, ipsec and networking. The intel-opi-bridge (further bridge) acts as a gRPC server for xPU management and configuration. See Intel xPU (IPU) for more details about IPU.

The diagram below illustrates main system components of an exemplary xPU NVMe-oF initiator deployment. The bridge (in blue) runs on an xPU and translates OPI API commands to appropriate sequences of Intel SDK instructions. Ultimately, two emulated NVMe/PCIe storage devices are exposed to the host. These devices are backed by an "over Fabrics"-connection to some remote storage backends while the host has an illusion of accessing locally attached storage and can run standard and unmodified apps/drivers to access it. Storage-related services and computations are offloaded from the host and accelerated on the xPU itself.

Fig. 1 - System components in NVMe-oF initiator scenario.

Next to the initiator mode, the xPU can also be run in a target mode and serve as an acceleration and virtualization layer for locally attached SSD drives (JBOF usage model). Note that in this case xPU is not required to be plugged into a physical server and runs headless as a low-power, low-cost storage appliance. Customized storage services can be run on the xPU as well to realize arbitrary storage operations. In the diagram below a standard NVMe/TCP driver is used on a host to access physical storage which is exposed by the xPU over network via two NVMe namespaces.

Fig. 2 - System components in NVMe-oF target scenario.

Combining both above usage scenarios results in xPU acting as both initiator and target to accelerate NVMe-oF communication on both ends of a network connection - see the diagram below. Hyperconverged use cases are possible if two xPUs are plugged into the same physical server

Fig. 3 - System components in a combined NVMe-oF initiator and target scenario with two independent xPUs.

or if an xPU is run in initiator and target mode simultaneously.

Fig. 4 - System components in a combined NVMe-oF initiator and target scenario with one xPU running in both modes simultaneously.

Quickstart

This section outlines the basic steps to get you up-and-running with the bridge and shows some examples of its usage to expose storage devices to the host, set bandwidth/rate limiters on them or enable data-at-rest crypto. The steps are mainly executed as gRPC commands to the bridge but may also involve some host-side interactions or initial xPU-side setup.

Note
It is assumed that Intel IPU is already properly set up to be used with Intel OPI bridge.

The following variables are used throughout this document:

Variable	Description
BRIDGE_IP	opi-intel-bridge gRPC/HTTP listening IP address e.g. 10.10.10.10 or localhost
BRIDGE_PORT	opi-intel-bridge gRPC listening port e.g. 50051
BRIDGE_ADDR	BRIDGE_IP:BRIDGE_PORT
BRIDGE_HTTP_PORT	opi-intel-bridge http gateway port e.g. 8082
NVME_PF_BDF	physical function PCI address e.g. 0000:3b:00.1 for Nvme
NVME_VF_BDF	virtual function PCI address e.g. 0000:40:00.0 can be found in pf's virtfn<X> where X equals to virtual_function in CreateNvmeController minus 1
BLK_PF_BDF	physical function PCI address e.g. 0000:af:01.0 for virtio-blk
TARGET_IP	storage target ip address
TARGET_PORT	storage target port

Build and import

To build the solution execute

go build -v -o /opi-intel-bridge ./cmd/...

To import the bridge within another go package or module use

import "github.com/opiproject/opi-intel-bridge/pkg/frontend"

Usage

Before initiating the bridge, the Redis and Jaeger services must be operational. To specify non-standard ports for these services, use the --help command with the binary to find out which parameters needs to be passed.

According to this guideline, the Docker should be installed and appropriately configured in compliance with your organization's policies, such as the utilization of a Proxy, to ensure its proper functioning.

On xPU run

$ docker run --rm -it -v /var/tmp/:/var/tmp/ -p $BRIDGE_PORT:$BRIDGE_PORT -p $BRIDGE_HTTP_PORT:$BRIDGE_HTTP_PORT ghcr.io/opiproject/opi-intel-bridge:main /opi-intel-bridge -grpc_port=$BRIDGE_PORT -http_port=$BRIDGE_HTTP_PORT

2023/09/12 20:29:05 TLS files are not specified. Use insecure connection.
2023/09/12 20:29:05 Connection to SPDK will be via: unix detected from /var/tmp/spdk.sock
2023/09/12 20:29:05 gRPC server listening at [::]:50051
2023/09/12 20:29:05 HTTP Server listening at 8082

To send commands to the bridge, grpc_cli tool is used. It can be used as a containerized or a native version. If containerized version is preferable, then an alias can be defined as follows

alias grpc_cli="docker run --network=host --rm -it namely/grpc-cli"

On management machine run below command to check bridge availability and reflection capabilities

$ grpc_cli ls --json_input --json_output $BRIDGE_ADDR

grpc.reflection.v1alpha.ServerReflection
opi_api.inventory.v1.InventorySvc
opi_api.security.v1.IPsec
opi_api.storage.v1.AioControllerService
opi_api.storage.v1.FrontendNvmeService
opi_api.storage.v1.FrontendVirtioBlkService
opi_api.storage.v1.FrontendVirtioScsiService
opi_api.storage.v1.MiddleendEncryptionService
opi_api.storage.v1.MiddleendQosVolumeService
opi_api.storage.v1.NvmeRemoteControllerService
opi_api.storage.v1.NullDebugService

run either gRPC or HTTP requests

# gRPC requests
# Nvme PF creation
grpc_cli call --json_input --json_output $BRIDGE_ADDR CreateNvmeSubsystem "{nvme_subsystem : {spec : {nqn: 'nqn.2022-09.io.spdk:opitest2', serial_number: 'myserial2', model_number: 'mymodel2', max_namespaces: 11} }, nvme_subsystem_id : 'subsystem2' }"
grpc_cli call --json_input --json_output $BRIDGE_ADDR ListNvmeSubsystems "{}"
grpc_cli call --json_input --json_output $BRIDGE_ADDR GetNvmeSubsystem "{name : 'nvmeSubsystems/subsystem2'}"
grpc_cli call --json_input --json_output $BRIDGE_ADDR CreateNvmeController "{parent: 'nvmeSubsystems/subsystem2', nvme_controller : {spec : {nvme_controller_id: 2, pcie_id : {physical_function : 0, virtual_function : 0, port_id: 0}, max_nsq:5, max_ncq:5, 'trtype': 'NVME_TRANSPORT_TYPE_PCIE' } }, nvme_controller_id : 'controller1'}"
grpc_cli call --json_input --json_output $BRIDGE_ADDR ListNvmeControllers "{parent : 'nvmeSubsystems/subsystem2'}"
grpc_cli call --json_input --json_output $BRIDGE_ADDR GetNvmeController "{name : 'nvmeSubsystems/subsystem2/nvmeControllers/controller1'}"

# Nvme VF creation on PF0
grpc_cli call --json_input --json_output $BRIDGE_ADDR CreateNvmeSubsystem "{nvme_subsystem : {spec : {nqn: 'nqn.2022-09.io.spdk:opitest3', serial_number: 'mev-opi-serial', model_number: 'mev-opi-model', max_namespaces: 11} }, nvme_subsystem_id : 'subsystem03' }"
grpc_cli call --json_input --json_output $BRIDGE_ADDR CreateNvmeController "{parent: 'nvmeSubsystems/subsystem03', nvme_controller : {spec : {nvme_controller_id: 2, pcie_id : {physical_function : 0, virtual_function : 3, port_id: 0 }, max_nsq:5, max_ncq:5, 'trtype': 'NVME_TRANSPORT_TYPE_PCIE' } }, nvme_controller_id : 'controller3'}"

# Create Nvme/TCP controller
grpc_cli call --json_input --json_output $BRIDGE_ADDR CreateNvmeSubsystem "{nvme_subsystem : {spec : {nqn: 'nqn.2022-09.io.spdk:opitest4', serial_number: 'myserial2', model_number: 'mymodel2', max_namespaces: 11} }, nvme_subsystem_id : 'subsystem4' }"
grpc_cli call --json_input --json_output $BRIDGE_ADDR CreateNvmeController "{'parent':'nvmeSubsystems/subsystem4','nvme_controller':{'spec':{'nvme_controller_id':2,'fabrics_id':{'traddr': '127.0.0.1', trsvcid: '4421', adrfam: 'NVME_ADDRESS_FAMILY_IPV4'}, 'max_nsq':5,'max_ncq':5, 'trtype': 'NVME_TRANSPORT_TYPE_TCP'}},'nvme_controller_id':'controller4'}"
grpc_cli call --json_input --json_output $BRIDGE_ADDR GetNvmeController "{name : 'nvmeSubsystems/subsystem4/nvmeControllers/controller4'}"

# Connect to remote storage-target
grpc_cli call --json_input --json_output $BRIDGE_ADDR CreateNvmeRemoteController "{nvme_remote_controller : {multipath: 'NVME_MULTIPATH_MULTIPATH'}, nvme_remote_controller_id: 'nvmetcp12'}"
grpc_cli call --json_input --json_output $BRIDGE_ADDR ListNvmeRemoteControllers "{}"
grpc_cli call --json_input --json_output $BRIDGE_ADDR GetNvmeRemoteController "{name: 'nvmeRemoteControllers/nvmetcp12'}"
grpc_cli call --json_input --json_output $BRIDGE_ADDR CreateNvmePath "{parent: 'nvmeRemoteControllers/nvmetcp12', nvme_path : {traddr:'11.11.11.2', trtype:'NVME_TRANSPORT_TYPE_TCP', fabrics:{subnqn:'nqn.2016-06.com.opi.spdk:target0', trsvcid:'4444', adrfam:'NVME_ADDRESS_FAMILY_IPV4', hostnqn:'nqn.2014-08.org.nvmexpress:uuid:feb98abe-d51f-40c8-b348-2753f3571d3c'}}, nvme_path_id: 'nvmetcp12path0'}"
grpc_cli call --json_input --json_output $BRIDGE_ADDR ListNvmePaths "{parent : 'nvmeRemoteControllers/nvmetcp12'}"
grpc_cli call --json_input --json_output $BRIDGE_ADDR GetNvmePath "{name: 'nvmeRemoteControllers/nvmetcp12/nvmePaths/nvmetcp12path0'}"

# Connect to local PCIe storage-target
grpc_cli call --json_input --json_output $BRIDGE_ADDR CreateNvmeRemoteController "{nvme_remote_controller : {multipath: 'NVME_MULTIPATH_DISABLE'}, nvme_remote_controller_id: 'nvmepcie13'}"
grpc_cli call --json_input --json_output $BRIDGE_ADDR CreateNvmePath "{parent: 'nvmeRemoteControllers/nvmepcie13', nvme_path : {traddr:'0000:01:00.0', trtype:'NVME_TRANSPORT_TYPE_PCIE'}, nvme_path_id: 'nvmepcie13path0'}"

# Virtio-blk PF creation (virtio-blk requires a volume, that's why it is created after connection to storage-target)
grpc_cli --json_input --json_output call $BRIDGE_ADDR CreateVirtioBlk "{virtio_blk_id: 'virtioblk0', virtio_blk : { volume_name_ref: 'nvmetcp12n0', pcie_id: { physical_function: '0', virtual_function: '0', port_id: '0'}}}"

# Create QoS volume
grpc_cli call --json_input --json_output $BRIDGE_ADDR CreateQosVolume "{'qos_volume' : {'volume_name_ref' :'nvmetcp12n1', 'limits' : { 'max': {'rw_iops_kiops': 3} } }, 'qos_volume_id' : 'qosnvmetcp12n1' }"

# Create encrypted volume
grpc_cli call --json_input --json_output $BRIDGE_ADDR CreateEncryptedVolume "{'encrypted_volume': { 'cipher': 'ENCRYPTION_TYPE_AES_XTS_128', 'volume_name_ref': 'nvmetcp12n1', 'key': 'MDAwMTAyMDMwNDA1MDYwNzA4MDkwYTBiMGMwZDBlMGY='}, 'encrypted_volume_id': 'encnvmetcp12n1' }"

# Create namespace
grpc_cli call --json_input --json_output $BRIDGE_ADDR CreateNvmeNamespace "{parent: 'nvmeSubsystems/subsystem2', nvme_namespace : {spec : {volume_name_ref : 'nvmetcp12n1', 'host_nsid' : '10', uuid:'1b4e28ba-2fa1-11d2-883f-b9a761bde3fb', nguid: '1b4e28ba-2fa1-11d2-883f-b9a761bde3fb', eui64: 1967554867335598546 } }, nvme_namespace_id: 'namespace1'}"
grpc_cli call --json_input --json_output $BRIDGE_ADDR ListNvmeNamespaces "{parent : 'nvmeSubsystems/subsystem2'}"
grpc_cli call --json_input --json_output $BRIDGE_ADDR GetNvmeNamespace "{name : 'nvmeSubsystems/subsystem2/nvmeNamespaces/namespace1'}"
grpc_cli call --json_input --json_output $BRIDGE_ADDR StatsNvmeNamespace "{name : 'nvmeSubsystems/subsystem2/nvmeNamespaces/namespace1'}"

# Delete namespace
grpc_cli call --json_input --json_output $BRIDGE_ADDR DeleteNvmeNamespace "{name : 'nvmeSubsystems/subsystem2/nvmeNamespaces/namespace1'}"

# Delete encrypted volume
grpc_cli call --json_input --json_output $BRIDGE_ADDR DeleteEncryptedVolume "{'name': 'volumes/encnvmetcp12n1'}"

# Delete QoS volume
grpc_cli call --json_input --json_output $BRIDGE_ADDR DeleteQosVolume "{name : 'volumes/qosnvmetcp12n1'}"

# Delete virtio-blk PF
grpc_cli call --json_input --json_output $BRIDGE_ADDR DeleteVirtioBlk "{name: 'volumes/virtioblk0'}"

# Disconnect from local PCIe storage-target
grpc_cli call --json_input --json_output $BRIDGE_ADDR DeleteNvmePath "{name: 'nvmeRemoteControllers/nvmepcie13/nvmePaths/nvmepcie13path0'}"
grpc_cli call --json_input --json_output $BRIDGE_ADDR DeleteNvmeRemoteController "{name: 'nvmeRemoteControllers/nvmepcie13'}"

# Disconnect from remote storage-target
grpc_cli call --json_input --json_output $BRIDGE_ADDR DeleteNvmePath "{name: 'nvmeRemoteControllers/nvmetcp12/nvmePaths/nvmetcp12path0'}"
grpc_cli call --json_input --json_output $BRIDGE_ADDR DeleteNvmeRemoteController "{name: 'nvmeRemoteControllers/nvmetcp12'}"

# Delete Nvme VF
grpc_cli call --json_input --json_output $BRIDGE_ADDR DeleteNvmeController "{name : 'nvmeSubsystems/subsystem03/nvmeControllers/controller3'}"
grpc_cli call --json_input --json_output $BRIDGE_ADDR DeleteNvmeSubsystem "{name : 'nvmeSubsystems/subsystem03'}"

# Delete Nvme PF
grpc_cli call --json_input --json_output $BRIDGE_ADDR DeleteNvmeController "{name : 'nvmeSubsystems/subsystem2/nvmeControllers/controller1'}"
grpc_cli call --json_input --json_output $BRIDGE_ADDR DeleteNvmeSubsystem "{name : 'nvmeSubsystems/subsystem2'}"

# Delete Nvme/TCP
grpc_cli call --json_input --json_output $BRIDGE_ADDR DeleteNvmeController "{name : 'nvmeSubsystems/subsystem4/nvmeControllers/controller4'}"
grpc_cli call --json_input --json_output $BRIDGE_ADDR DeleteNvmeSubsystem "{name : 'nvmeSubsystems/subsystem4'}"

# HTTP requests
# inventory
curl -kL http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/inventory/1/inventory/2

# Nvme
# create
curl -X POST -f http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeRemoteControllers?nvme_remote_controller_id=nvmetcp12 -d '{"multipath": "NVME_MULTIPATH_MULTIPATH"}'
curl -X POST -f http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeRemoteControllers/nvmetcp12/nvmePaths?nvme_path_id=nvmetcp12path0 -d "{\"traddr\":\"$TARGET_IP\", \"trtype\":\"NVME_TRANSPORT_TYPE_TCP\", \"fabrics\":{\"subnqn\":\"nqn.2016-06.com.opi.spdk:target0\", \"trsvcid\":\"$TARGET_PORT\", \"adrfam\":\"NVME_ADDRESS_FAMILY_IPV4\", \"hostnqn\":\"nqn.2014-08.org.nvmexpress:uuid:feb98abe-d51f-40c8-b348-2753f3571d3c\"}}"
curl -X POST -f http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeSubsystems?nvme_subsystem_id=subsys0 -d '{"spec": {"nqn": "nqn.2022-09.io.spdk:opitest1"}}'
curl -X POST -f http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeSubsystems/subsys0/nvmeNamespaces?nvme_namespace_id=namespace0 -d '{"spec": {"volume_name_ref": "Malloc0", "host_nsid": 10}}'
curl -X POST -f http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeSubsystems/subsys0/nvmeControllers?nvme_controller_id=ctrl0 -d '{"spec": {"trtype": "NVME_TRANSPORT_TYPE_TCP", "fabrics_id":{"traddr": "127.0.0.1", "trsvcid": "4421", "adrfam": "NVME_ADDRESS_FAMILY_IPV4"}}}'
# get
curl -X GET -f http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeRemoteControllers/nvmetcp12
curl -X GET -f http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeRemoteControllers/nvmetcp12/nvmePaths/nvmetcp12path0
curl -X GET -f http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeSubsystems/subsys0
curl -X GET -f http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeSubsystems/subsys0/nvmeNamespaces/namespace0
curl -X GET -f http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeSubsystems/subsys0/nvmeControllers/ctrl0
# list
curl -X GET -f http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeRemoteControllers
curl -X GET -f http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeRemoteControllers/nvmetcp12/nvmePaths
curl -X GET -f http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeSubsystems
curl -X GET -f http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeSubsystems/subsys0/nvmeNamespaces
curl -X GET -f http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeSubsystems/subsys0/nvmeControllers
# stats
curl -X GET -f http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeRemoteControllers/nvmetcp12:stats
curl -X GET -f http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeRemoteControllers/nvmetcp12/nvmePaths/nvmetcp12path0:stats
curl -X GET -f http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeSubsystems/subsys0:stats
curl -X GET -f http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeSubsystems/subsys0/nvmeNamespaces/namespace0:stats
curl -X GET -f http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeSubsystems/subsys0/nvmeControllers/ctrl0:stats
# update
curl -X PATCH -f http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeRemoteControllers/nvmetcp12 -d '{"multipath": "NVME_MULTIPATH_MULTIPATH"}'
curl -X PATCH -f http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeRemoteControllers/nvmetcp12/nvmePaths/nvmetcp12path0 -d "{\"traddr\":\"$TARGET_ADDR\", \"trtype\":\"NVME_TRANSPORT_TYPE_TCP\", \"fabrics\":{\"subnqn\":\"nqn.2016-06.com.opi.spdk:target0\", \"trsvcid\":\"$TARGET_PORT\", \"adrfam\":\"NVME_ADDRESS_FAMILY_IPV4\", \"hostnqn\":\"nqn.2014-08.org.nvmexpress:uuid:feb98abe-d51f-40c8-b348-2753f3571d3c\"}}"
curl -X PATCH -k http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeSubsystems/subsys0/nvmeNamespaces/namespace0 -d '{"spec": {"volume_name_ref": "Malloc1", "host_nsid": 10}}'
curl -X PATCH -k http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeSubsystems/subsys0/nvmeControllers/ctrl0 -d '{"spec": {"trtype": "NVME_TRANSPORT_TYPE_TCP", "fabrics_id":{"traddr": "127.0.0.1", "trsvcid": "4421", "adrfam": "NVME_ADDRESS_FAMILY_IPV4"}}}'
# delete
curl -X DELETE -f http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeSubsystems/subsys0/nvmeControllers/ctrl0
curl -X DELETE -f http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeSubsystems/subsys0/nvmeNamespaces/namespace0
curl -X DELETE -f http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeSubsystems/subsys0
curl -X DELETE -f http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeRemoteControllers/nvmetcp12/nvmePaths/nvmetcp12path0
curl -X DELETE -f http://$BRIDGE_IP:$BRIDGE_HTTP_PORT/v1/nvmeRemoteControllers/nvmetcp12

To observe Nvme devices on host:

After PF is created

# Bind driver to PF
modprobe nvme
cd /sys/bus/pci/devices/$NVME_PF_BDF
echo 'nvme' > ./driver_override
echo $NVME_PF_BDF > /sys/bus/pci/drivers/nvme/bind

# Allocate resources and prepare for VF creation
echo 0 > ./sriov_drivers_autoprobe
echo 4 > ./sriov_numvfs

After VF is created

cd /sys/bus/pci/devices/$NVME_PF_BDF
echo 'nvme' > ./virtfn0/driver_override
echo $NVME_VF_BDF > /sys/bus/pci/drivers/nvme/bind

Before VF is deleted

cd /sys/bus/pci/devices/$NVME_PF_BDF
echo $NVME_VF_BDF > /sys/bus/pci/drivers/nvme/unbind
echo '(null)' > ./virtfn2/driver_override

Before PF is deleted

cd /sys/bus/pci/devices/$NVME_PF_BDF
echo $NVME_PF_BDF > /sys/bus/pci/drivers/nvme/unbind
echo '(null)' > ./driver_override

To observe Virtio-blk devices on host:

After PF is created

echo 1 > /sys/bus/pci/devices/$BLK_PF_BDF/remove
echo 1 > /sys/bus/pci/rescan

Mutual TLS setup

In order to pass configuration data to the xPU securely and only by authenticated/allowed clients it is recommended to secure the gRPC port with mutual TLS.

Warning
The steps outlined below use self-signed certificates and serve only demonstration purposes. It is up to the integrator of the solution to securely provision the keys and certificates to the server and follow up-to-date crypto recommendations, e.g. NIST TLS Guidelines and NIST Cryptographic Standards and Guidelines.

The following variables are used in the instructions below:

Variable	Description
SAN_IP	subject alternative name in form of ip address e.g. 10.10.10.10 for TLS certificate
SERVER_CERT	server certificate file path e.g. /etc/opi/server-cert.pem
SERVER_KEY	server key file path e.g. /etc/opi/server-key.pem
CA_CERT	server CA certificate file path e.g. /etc/opi/ca-cert.pem
CLIENT_CERT	client certificate file path e.g. /etc/opi/client-cert.pem
CLIENT_KEY	client key file path e.g. /etc/opi/client-key.pem

Generate certificates/keys

This section describes how to generate TLS self-signed certificates. The root level Certificate Authority (CA) is used to generate server-side key and cert files, and client-side key and cert files. This results in a 1-depth level certificate chain, which will suffice for verification and validation purposes but may not provide sufficient security for production systems. It is highly recommended to use well-known CAs, and generate certificates at multiple depth levels in order to conform to higher security standards.

# create config files
echo "subjectAltName=IP:$SAN_IP" > server-ext.cnf
echo "subjectAltName=IP:$SAN_IP" > client-ext.cnf
# generate CA certificate
openssl req -x509 -newkey rsa:4096 -days 365 -nodes -keyout ca-key.pem -out ca-cert.pem -sha384
# generate server private key and signing request
openssl req -newkey rsa:4096 -nodes -keyout server-key.pem -out server-req.pem -sha384
# use CA's private key to get signed server certificate
openssl x509 -req -in server-req.pem -days 365 -CA ca-cert.pem -CAkey ca-key.pem -CAcreateserial -out server-cert.pem -extfile server-ext.cnf
# generate client private key and signing request
openssl req -newkey rsa:4096 -nodes -keyout client-key.pem -out client-req.pem -sha384
# use CA's private key to get signed client certificate
openssl x509 -req -in client-req.pem -days 365 -CA ca-cert.pem -CAkey ca-key.pem -CAcreateserial -out client-cert.pem -extfile client-ext.cnf

copy server related certificates/keys to a dedicated secure location on xPU

mkdir /etc/opi
cp server-cert.pem /etc/opi
cp server-key.pem /etc/opi
cp ca-cert.pem /etc/opi

make sure to follow the principle of least privilege for access permissions and change ownership to a dedicated user.

Run server

Run bridge binary specifying TLS-related server key/certificate and CA cert

./opi-intel-bridge -grpc_port=$BRIDGE_PORT -http_port=$BRIDGE_HTTP_PORT -tls $SERVER_CERT:$SERVER_KEY:$CA_CERT

for container

docker run --network=host -v "/var/tmp:/var/tmp" -v "/etc/opi:/etc/opi" ghcr.io/opiproject/opi-intel-bridge:main /opi-intel-bridge -grpc_port=$BRIDGE_PORT -http_port=$BRIDGE_HTTP_PORT -tls $SERVER_CERT:$SERVER_KEY:$CA_CERT

Send client commands

To send by means of not-containerized grpc_cli:

GRPC_DEFAULT_SSL_ROOTS_FILE_PATH="$CA_CERT" grpc_cli --json_input --json_output --channel_creds_type=ssl --ssl_client_cert="$CLIENT_CERT" --ssl_client_key="$CLIENT_KEY" call $BRIDGE_ADDR ListAioControllers "{}"

I Want To Contribute

This project welcomes contributions and suggestions. We are happy to have the Community involved via submission of Issues and Pull Requests (with substantive content or even just fixes). We are hoping for the documents, test framework, etc. to become a community process with active engagement. PRs can be reviewed by any number of people, and a maintainer may accept.

See CONTRIBUTING and GitHub Basic Process for more details.

For reporting security vulnerabilities see SECURITY.md.

Name		Name	Last commit message	Last commit date
Latest commit History 572 Commits
.github		.github
cmd		cmd
doc/images		doc/images
pkg		pkg
.editorconfig		.editorconfig
.gitignore		.gitignore
.golangci.yml		.golangci.yml
.markdownlintrc		.markdownlintrc
.pre-commit-config.yaml		.pre-commit-config.yaml
CHANGELOG.md		CHANGELOG.md
Dockerfile		Dockerfile
LICENSE		LICENSE
Makefile		Makefile
README.md		README.md
SECURITY.md		SECURITY.md
docker-compose.yml		docker-compose.yml
go.mod		go.mod
go.sum		go.sum

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

Repository files navigation

OPI gRPC to Intel SDK bridge

Quickstart

Build and import

Usage

Mutual TLS setup

Generate certificates/keys

Run server

Send client commands

I Want To Contribute

About

Releases

Packages

Languages

License

artek-koltun/opi-intel-bridge

Folders and files

Latest commit

History

Repository files navigation

OPI gRPC to Intel SDK bridge

Quickstart

Build and import

Usage

Mutual TLS setup

Generate certificates/keys

Run server

Send client commands

I Want To Contribute

About

Resources

License

Security policy

Stars

Watchers

Forks

Releases

Packages 0

Languages

Packages