v13.1.0

[dalathegreat]

What's Changed 📦

New batteries supported 🔋

This version adds support for Stellantis Pro One 110kWh packs , Ennoid Maxkgo batteries, and OEM BYD Battery-Box can now be used on inverters not even supporting BYD house batteries!

DTC Descriptions even when offline 🚫

In this version, DTC descriptions are baked into the software. This means you will get full DTC description decoding even on an offline system, as long as you are on large flash memory Battery-Emulator hardware (<4MB) Sorry T-CAN485 users, another good reason to update to newer BE hardware!

Optional super accurate current measurement 🔬

We now support using a "QNHCK2-16 Hall current sensor" directly with Battery-Emulator to get super precise current measurement data in the system, and into MQTT.

General fixes 🔧

Apart from all this, there are several other bugfixes and enhancements. Please check out the full list of changes below before updating

Taking this release into use ⚙️

Important

In order to OTA update to this version, you already need to be on a v10 release!

Note that v10 was a major new release of the Battery-Emulator software. The first time when taking a version > v10.0.0 into use, you are required to perform an initial one time USB setup via this webpage! This is because we changed the flash frequencies, partitioning layouts and other under the hood changes to ensure longterm system stability. After any v10 has been installed via USB, following 10.X.X releases can be updated over the air.

Quickstart video: https://youtu.be/sR3t7j0R9Z0

Batteries 🔋

• New battery 🔋 Stellantis Pro One: Add support for 110kWh (E-Ducato/ProMaster/Proace) by @dalathegreat & @TPPS999 in Stellantis Pro One: Add support for 110kWh (E-Ducato/ProMaster/Proace) #2543
• New battery 🔋 Update ENNOID protocol to support with Maxkgo batteries by @dalathegreat in New battery 🔋 Update ENNOID with Maxkgo data #3054
• New battery 🔋 Add support for BYD Battery-Box Premium by @dalathegreat in New battery 🔋 Add support for BYD Battery-Box Premium #2887
• PylonHV/Rivian/GrowattHV/SimpBMS: Fix unintended rounding on low current by @ngehrsitz in PylonHV/Rivian/GrowattHV/SimpBMS: Fix unintended rounding on low current #3070
• Geely SEA: Avoid fake warning events related to temperature by @dalathegreat in Geely SEA: Avoid fake warning events related to temperature #3073
• MG Gen1: Tweak autodetection to correctly cover another 69.9kWh pack by @jonny5532 in MG Gen1: Tweak autodetection to correctly cover another 69.9kWh pack #3096
• All batteries: Reduce likelyhood of false positive temperature events on startup by @dalathegreat in Batteries: Avoid false positive temperature events on boot #3084
• DTC: Improve mappings for ECMP and Ford by @dalathegreat in DTC: Improve mappings for ECMP and Ford #3068
• Improvement: Battery 2/3 safeties ⚠️ by @nagyrobi in Improvement: Battery 2/3 safeties ⚠️ #3071
• Kia-Hyundai 64/40kWh: Avoid spamming battery with CAN messages when it is not started up by @dalathegreat in Kia64: Avoid spamming battery with CAN messages when it is not started up #3085
• Kia-Hyundai 64/40kWh: Fixed regression introduced in v13.0 where battery would fail to poll UDS values by @dalathegreat in Kia64: Avoid spamming battery with CAN messages when it is not started up #3085

Inverters ⚡

• Pylon LV RS485: Fix CID2/RTN mixup and wrong command codes by @schmellic in Fix PYLON-LV-RS485 CID2/RTN mixup and wrong command codes #3003
• Pylon LV RS485: Fix temperature tests after the RTN change by @nagyrobi in Fix Pylon LV RS485 temperature tests after the RTN change #3079
• Pylon LV RS485: Honor manual charge/discharge voltages by @triangledog in Honor manual charge/discharge voltages in Pylon LV RS485 #3074

Connectivity

• MQTT: add SET_SCALESOC command to change SOC scaling limits at runtime by @nagyrobi in MQTT: add SET_SCALESOC command to change SOC scaling limits at runtime #3050
• Support DNS lookup for Syslog servers by @ngehrsitz in Support DNS lookup for Syslog servers #2930

Hardware 🤖

• Shunt: Add QNHCK2-16 Hall current sensor as a measurement peripheral by @nagyrobi in Shunt: Add QNHCK2-16 Hall current sensor as a measurement peripheral #3059
• Improvement: QNHCK2-16 temperature compensation by @nagyrobi in Improvement: QNHCK2-16 temperature compensation #3086

Housekeeping 🧹

• Improvement: Settings reject sharing one CAN interface between batteries by @nagyrobi in Improvement: Settings reject sharing one CAN interface between batteries #3072
• Improvement: Initialize battery3 override charge/discharge power from NVM by @nizmot in Initialize battery3 override charge/discharge power from NVM #3093
• Improvement: Embed the DTC descriptions in big flash builds by @nagyrobi in Improvement: Embed the DTC descriptions in big flash builds #3078
• Optimization: Leave CHAdeMO out of the small flash builds by @nagyrobi in Leave CHAdeMO out of the small flash builds #3080
• Github: [pre-commit.ci] pre-commit autoupdate by @pre-commit-ci[bot] in [pre-commit.ci] pre-commit autoupdate #3088

Full Changelog: v13.0.0...v13.1.0

---

This discussion was created from the release v13.1.0.