High performance GPIO tool kit for raspberry pi, including quadrature_decoder, DC motor control, soft PWM, buttons, etc. Based on c wiringpi.
npm install perf-gpio --save
Note: perf-gpio depend on dynamic-linked wiringPi at run-time, make sure you have wiringPi installed (/usr/local/lib/libwiringPi.so
file).
https://pinout.xyz/pinout/wiringpi# is the best doc I can find for wiringpi Pin number mappings.
var onoff = require('perf-gpio').onoff;
// wiring-pi 2 = GPIO27 = PIN13
var led = onoff(2);
led.set(1);
var onoff = require('perf-gpio').onoff;
// wiring-pi 2 = GPIO27 = PIN13
var led = onoff(2);
var current = false;
setTimeout(timeout, 1000);
function timeout() {
setTimeout(timeout, 1000);
current = !current;
led.set(current);
console.log(current);
}
var button = require('perf-gpio').button;
// wiring-pi 3 = GPIO22 = PIN15
var b = button(3, button.PUD_UP); // use raspberry pi build-in 50k pull-up resistor
setTimeout(timeout, 1000);
function timeout() {
setTimeout(timeout, 1000);
var current = b.get();
console.log(current);
}
var button = require('perf-gpio').button;
// wiring-pi 3 = GPIO22 = PIN15
var b = button(3, button.PUD_UP);
b.watch(function(err, status) {
console.log(status? 'UP' : 'DOWN');
});
var inputBank = require('perf-gpio').inputBank();
// wiring-pi 25/24/23 = GPIO26/19/13 = PIN37/35/33
var bank = inputBank([25, 24, 23], "PUD_DOWN");
setTimeout(timeout, 1000);
function timeout() {
setTimeout(timeout, 1000);
var val = bank();
// bit mask: bit 0 <= wp25, bit 1 <= wp24, bit 2 <= wp23
console.log(val);
}
- Note:
inputBank
support batch read, but don't support edge-triggered callback. If you need callback, consider usingbutton
. - Note:
inputBank
andbutton
can share the same pin. Under the hood they are both "input" mode, thus no conflict.
var qd = require('perf-gpio').quadrature_decoder;
// quadrature_decoder you need 2 pins, phase A and B
// wiringpi PIN 0 and 1, maps to BCM GPIO 17 and 18
var counter = qd(0,1);
timeout();
function timeout() {
setTimeout(timeout, 1000);
console.log(counter.getCounter());
}
var led = require('perf-gpio').led();
var pin = led(25); // wiringPi 25, GPIO 26
pin(0.5); // 50% on
var led = require('perf-gpio').led();
var pin = led(25); // wiringPi 25, GPIO 26
pin(1);
setTimeout(function() {
pin(0.5);
setTimeout(function() {
pin.close(); // turn off led before quit
led.shutdown(); // shutdown DMA device before quit
process.exit(0);
}, 2000);
}, 2000);
var motor = require('perf-gpio').motor();
// Need 2 pin to control a DC motor (forward/backword)
// you need a H-bridge module to drive a DC motor
var pin = motor(23, 25);
pin(-0.5); // anywhere range from [-1.0, +1.0]
function timeout() {
pin.close(); // turn off motor before quit
motor.shutdown(); // shutdown DMA device before quit
process.exit(0);
}
setTimeout(timeout, 2000);
Note: DC motor and LED shares the same DMA channel (14 for pi2/3/zero and 7 for pi4), 5ms cycle with 2us step size.
var servo = require('perf-gpio').servo();
var pin = servo(29); // wiringpi_25=gpio_21=Phys_40
pin(1500); // 1.5ms (mid)
setTimeout(function () {
pin(500); // 0.5ms (min)
setTimeout(function () {
pin(2500); // 2.5ms (max)
setTimeout(function () {
pin(1500); // 1.5ms (mid)
setTimeout(function () {
servo.shutdown();
process.exit(0);
}, 500);
}, 1000);
}, 1000);
}, 1000);
Note: Servo runs on it's own DMA channel (13 for pi2/3/zero and 6 for pi4), 20ms cycle with 10us step size.
var clockOut = require('./index').clockOut();
// wiring-pi 22 = GPIO6 = PIN31
var pinNum = 22;
var pin = clockOut(pinNum);
pin.setFeq(10000); // 10kHz
.....
pin.shutdown();
- Note: This hardware clock, only available from a few pin.
- Note: If don't shutdown, pi continue output clock even after your programe exits!
- Note: valid range from [4.7k, 19.2M] (Hz)
- Performance is the main reason I write this library.
- perf-gpio is based on c wiringPi, most of the interrupt handling is done in c code. This is especially important for quadrature_decoder, so far perf-gpio is probably the best quadrature decoder available on raspberry-pi.
- The DMA-PWM is based on rpio-pwm, which is the best (if not the only) DMA-PWM solution on node.js (that's the reason I spend my time created it).
- perf-gpio also supports pull-up/down resistors (which is a must-have for my project).
MIT