Repository navigation
Methods
Each method returns t, which is used to compute the next point with the formula
x = x2 + t ( x1 - x2 )
Three edge cases are considered.
-
If x1 - x2 leads to overflow, t = 0.5 is set to indicated binary search is used, and x = 0 is set.
-
If f ( x ) is infinite, t = 0.5 is set to indicate binary search is used because interpolation is unreliable in this situation.
-
If t = 0.5 is set, then Binary Search is used.
Finally, an adjustment is made so that searching over intervals smaller than the desired error is avoided. This is done by rounding towards the midpoint of the interval.
x = x + 0.25 ( error + 10-14 | x | ) sign( ( x1 - x ) + ( x2 - x ) )
At the end of each iteration, a new value of t is chosen. To guarantee convergence, several additional measures are checked.
- If the bracketing interval fails to halve for 3 iterations, then
- The Illinois method is tried by using 0.25 f ( x1 ).
- If a quarter of the limit of iterations for the given method are used up, or the Illinois method has no effect, then t is quadrupled.
- If t > 0.5, then t = 0.5 to avoid going too far.
- If the bracketing interval fails to halve for 4 iterations, or t is out of bounds, then
- t = 0.5 is forced.
- This may be run twice in a row if the geometric mean is used first but the interval does not halve.
a.k.a. bisection
order = 1.000
A midpoint of the bracketing interval is used to halve either the absolute or relative errors. To halve the absolute error, the traditional arithmetic mean is used. To halve the relative error, the geometric mean is used. To ensure both are eventually halved, the two types of means used are alternated. See Binary Search for more details.
return t = 0.5
a.k.a. Regula Falsi and Secant
order = 1.414
The root is estimated using a secant line through x1 and x2.
return t = f ( x2 ) / ( f ( x2 ) - f ( x1 ) )
a.k.a. Quadratic
order = 1.731
The root is estimated using a quadratic interpolation through x1, x2, and x3. The root of the interpolating quadratic is computed with 2 iterations of Newton's method from the side of [ x1, x2] that is guaranteed to converge to the bracketed root.
a = ( f ( x1 ) - f ( x2 ) ) / ( x1 - x2 )
c = ( f ( x3 ) - f ( x2 ) ) / ( x3 - x2 )
b = ( a - c ) / ( x1 - x3 )
if b is 0:
- return t = f ( x2 ) / ( f ( x2 ) - f ( x1 ) )
if b and f ( x1 ) have the same sign:
- r = x1
else:
- r = x2
repeat two times:
- r -= ( f ( x2 ) + a ( r - x1 ) + b ( r - x1 ) ( r - x2 ) ) / ( a + b ( ( r - x1 ) + ( r - x2 ) ) )
return t = ( r - x2 ) / ( x1 - x2 )
order = 1.618
The root is estimated using a secant line through x2 and either x1 or x3. If x1 is closer to x2 than x1 or f ( x2 ) = f ( x3 ), then x1 is used. Otherwise x3 is used.
if f ( x2 ) = f ( x3 ) or t ≥ 0.5: return t = f ( x2 ) / ( f ( x2 ) - f ( x1 ) )
else: return t = ( f ( x2 ) / ( f ( x2 ) - f ( x3 ) ) ) ( ( x2 - x3 ) / ( x2 - x1 ) )
a.k.a. Brent-Dekker and fzeroin
order = 1.731
When possible, inverse quadratic interpolation through x1, x2, and x3 is used. If division by zero would occur, a secant line through x1 and x2 is used instead. Some conditions are then checked to use binary search instead if interpolation does not appear to be converging fast enough.
l = ( x3 - x2 ) / ( x1 - x2 )
a = f ( x2 ) / ( f ( x1 ) - f ( x2 ) )
b = f ( x3 ) / ( f ( x1 ) - f ( x3 ) )
c = f ( x2 ) / ( f ( x3 ) - f ( x2 ) )
d = f ( x1 ) / ( f ( x3 ) - f ( x1 ) )
t = a b + c d l
if division by zero occurs:
- t = f ( x2 ) / ( f ( x2 ) - f ( x1 ) )
if t < 0 or t > 1 or either
-
(binary search was last used and t | x1 - x2 | > 0.5 | x2 - x3 | )
-
(interpolation was last used and t | x1 - x2 | > 0.5 | x3 - x4 |)
- t = 0.5
return t
order = 1.731
Chandrupatla's method is very similar to Brent's method. The main difference is its more intelligent attempt at deciding when to use interpolation or binary search. Often Chandrupatla's method will be found to be more robust than Brent's method because it requires the three points ( x1, x2, x3 ) to be close to a straight line in order to use inverse quadratic interpolation.
ξ = ( x2 - x1 ) / ( x3 - x1 )
ϕ = ( f ( x2 ) - f ( x1 ) ) / ( f ( x3 ) - f ( x1 ) )
- If ξ2 < ϕ and ( 1 - ξ )2 < 1 - ϕ, then inverse quadratic interpolation is used.
- Otherwise t = 0.5 is used to indicate binary search should be used.




